• Journal of the Semiconductor & Display Technology
• /
• v.12 no.4
• /
• pp.15-20
• /
• 2013

Nanoimprint lithography (NIL) is the next generation photolithography process in which the photoresist is dispensed onto the substrate in its liquid form and then imprinted and cured into a desired pattern instead of using traditional optical system. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. In this paper, a pressure vessel type imprinting system was used to imprint patterns with two type pressure values (25 bar, 30 bar) and two type pressure keeping times (5 min, 10 min). The height of transferred pattern and the thickness of residual layer were measured and effects of pressurization conditions - pressure and pressure keeping time - on the pattern transfer in thermal NIL were investigated.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.288-290
• /
• 1997

Pulsed laser ablation has been used to fabricate superconducting $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The epitaxial YBCO thin films were grown at $750^{\circ}C$ and oxygen partial pressure of 200 mTorr. The electrical property and the characteristics of the YBCO thin films have been studied by R-T measurement. scanning electron microscopy (SEM) and X-ray diffraction (XRD). A microstrip line resonator has been fabricated using YBCO superconducting thin films by photolithography and wet-etch process. The resonator has linear microstrip line separated by a gap of 0.278 mm. We observed a fundamental resonance peak at the frequency of 10.007 GHz.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.402-407
• /
• 2011

The current paper describes a simpler ground-type, single-plate electrowetting configuration for droplet transport in digital microfluidics without performance degradation. The simplified fabrication process is achieved with two photolithography steps. The first step simultaneously patterns both a control electrode array and a reference electrode on a substrate. The second step patterns a dielectric layer at the top to expose the reference electrode for grounding the liquid droplet. In the experiment, a $5{\mu}m$ thick photo-imageable polyimide, with a 3.3 dielectric constant, is used as the dielectric layer. A 10 nm Teflon-AF is coated to obtain a hydrophobic surface with a high water advancing angle of $116^{\circ}$ and a small contact angle hysteresis of $5^{\circ}$. The droplet movement of 1 mM methylene blue on this simplified device is successfully demonstrated at control voltages above the required 45 V to overcome the contact angle hysteresis.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.12
• /
• pp.42-47
• /
• 2003

The laser direct writing method has some advantages of being maskless, allowing rapid and inexpensive prototyping in comparison to conventional mask-based photolithography. In general, there are two kinds of laser direct writing methods such as the laser ablation method and the laser polymerization method. The laser polymerization method was studied fur manufacturing waveguide in this paper. It is important to reduce line width for image mode waveguides, so some investigations will be carried out in various conditions of process parameters such as laser power, writing speed, focusing height and optical properties of polymer. Experimentally, the optical waveguide was manufactured trapezoid shape. Through SEM the waveguide was 20 ${\mu}{\textrm}{m}$ width and 7.4 ${\mu}{\textrm}{m}$ height.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.574-574
• /
• 2012

We report a simple way of fabricating high-quality carbon nanoscrolls (CNSs) by taking advantage of strain relief due to large difference in strain at the interface of graphene and underlying layer. This method allows strain-controlled self rolling-up of monolayer graphene during etching process at predefined positions on SiO2/Si substrates by photolithography. The size and the length of the CNSs can be easily controlled by adjusting the thickness of the underlying layer and by pre-patterning. Raman spectroscopy studies show that the CNSs is free of significant defects, and the electronic structure and phonon dispersion are slightly different from those of two-dimensional graphene. The preparation of high-quality CNSs may open up new opportunities for both fundamental and applied research of CNSs.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1314-1316
• /
• 1997

In this study, We fabricated thin film magnetic core inductors by using thin film manufacturing techniques such as photolithography and wet etching process. The inductors were prepared using multi-layered CoNbZr/Cu/CoNbZr. These devices are measured at high frequency range of $1\;MHz{\sim}1\;GHz$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.41-44
• /
• 1998

Dual mode resonators were fabricated using high temperature superconductor. The deposited material was $Y_1Ba_2Cu_3O_{7-x}$(YBCO) on MgO(100) substrate using pulsed laser deposition. Dual mode resonators were patterned by standard photolithography process and wet etching. At the back-side of the substrate, the ground plane with the metal layer of Ti and Ag was fabricated. The transition temperatures of YBCO films were 85-88 K, and network analyzer was used for testing the performance of the resonators. The input/output feedline angles of each resonator were $60^{\circ}$and $100^{\circ}$. The resonant frequency of resonators was 10 GHz. In this paper, dual mode resonator was fabricated for the application of satellite communication.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2004.05a
• /
• pp.229-233
• /
• 2004

The application of focused ion beam (FIB) technology in micro/nano machining has become increasingly popular. Its use in micro/nano machining has advantages over contemporary photolithography or other micro/nano machining technologies such as small feature resolution, the ability to process without masks and being accommodating for a variety of materials and geometries. This paper was carried out some experiments of the micro plasma electrode fabrications using FIB. The sputtering of FIB has one major problem that is redeposited by sputtered material including $Ga^+$ ion source. Therefore we have verified the effect of the reposition by EDX. And the optimal condition is suggested to machine the micro plasma electrode.

• Applied Science and Convergence Technology
• /
• v.23 no.1
• /
• pp.54-59
• /
• 2014

The roll-to-roll (R2R) fabrication method to make micro-scale pillar arrays for biomimetic functionalization of surfaces is presented. Inspired by the micro-structure of plants in nature, a surface with a synthetic micro-scale pillar array is fabricated via maskless photolithography. After the surface is SAM (self-assembled monolayer) coated with trichlorosilane in a vacuum desiccator, it displays a hydrophobic property even in R2R replicas of original substrate, whose properties are further characterized using various pitches and diameters. In order to perform a comparison between the original micro-pattern and its replicas, surface morphology was analyzed using scanning electron microscopy and wetting characteristics were measured via a contact angle measurement tool with a $10{\mu}L$ water droplet. Efficient roll-to-roll imprinting for a biomimetic functionalized surface has the potential for use in many fields ranging from water repelling and self-cleaning to microfluidic chips.

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.1-7
• /
• 1997

SAW filter has been used in mobile communication device, bandpass filter and resonator for merits )f miniaturization and high reliability. Materials for substrate mainly used single crystal such as LiNbO$_{3}$, LiTaO$_{3}$, ZnO. In this study, it was attempted that LiNbO$_{3}$ was substituted for piezoelectric ceramics(PZT4, PZT5A and PZT8) which had simple fabrication process because fabrication of crystal is difficult and it's cost is high. SAW filters were fabricated by the photolithography on piezoelectric ceramics substrates in order to compare their characteristics with LiNbO$_{3}$'s. The experimental value of center frequency was compared with theoretical one. The average difference of center frequency was 3.7%. PZT8 showed the best bandwidth properties among them. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than others.