• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.235-238
• /
• 1997

Basic properties of new cement pastes based on the system $CaO-Al_2O_3-P_O_5-H_2O$were studied Phosphoric acid solutions and calcium dialuminate clinkers synthesized by the hydration-burning method were used for liquid and powder components of the paste, respectively Variation in the compositions of the paste was achieved by changing the liquid/powder ratio and the concentration of phosphoric acid solution. The hardening rate of the paste was so largely affected by the amount of phosphoric acid that hardening was inhibited with the low-concentrated solution but was explosively accelerated with the high-concentrated solution. The phosphoric acid solutions of concentration of 45~50% and the liquid/powder ratio of 0.5~1.5 were favoured for the high early-strength cement paste with the reasonable hardening rate and high strength. The binding phase of hardened paste was the dense amorphous gel of the system $CaO-Al_2O_3-P_O_5-H_2O$. in which the unreacted calcium dialuminate grains were embeded.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.141-161
• /
• 1998

The depth and patterns of demineralization according to the difference in concentration and application time of phosphoric acid were observed through the transmission electron microscope, and shear bond strengths to the acid -conditioned dentin were then measured and compared with the TEM results. To investigate the influence of polymer addition into the phosphoric acid and the effect of difference in concentration and application time of the acid, the specimens were randomly divided into 9 groups. Among the specimens, the exposed dentin surfaces were acid-conditioned with 10% polymer-thickened phosphoric acid(All Bond 2, Bisco, U.S.A.) and aqueous 10%, 20%, 30%, 40% phosphoric acid for 20 seconds, The rest of the specimens were acid-conditioned with 10% phosphoric acid for 15s, 30s, 60s, 120s respectively. The specimens were immersed in 4% glutaraldehyde in 0.1M sodium cacodylate buffer and postfixed with 1 % osmium tetroxide without decalcification and then observed under a JEOL Transmission Electron Microscope(JEM 1200 EX II, Japan). After the specimens were acid-conditioned as the above, primer and adhesive resin were applied to blot-dried dentin and shear bond strengths were then measured and analysed. The results were as follows : 1. The intertubular demineralization depth of 4.0-$5.0{\mu}m$ in 10% polymer-thickened phosphoric acid gels was similar or slightly deeper than that of 4.0-$4.5{\mu}m$ in aqueous 10% phosphoric acid solution. 2. The intertubular demineralization depth of aqueous 20%, 30% and 40% phosphoric acid solution was 6.5-$7.0{\mu}m$, 6.5-$7.5{\mu}m$ and 9.0-$15.0{\mu}m$ respectively. It showed that the depth of dentin demineralization is partly related to the concentration of phosphoric acid solution. 3. The intertubular demineralization depth of aqueous 10% phosphoric acid solution in application time for 15s, 30s, 60s and 120s was 2.5-$3.0{\mu}m$, 4.0-$6.0{\mu}m$, 6.5-$7.0{\mu}m$ and 8.5-$14.0{\mu}m$ respectively. It showed that the depth of dentin demineralization is directly related to the application time of phosphoric acid solution. 4. The partially demineralized dentin layer between demineralized collagen layer and unaffected dentin was showed to a width of 0.5-$1.0{\mu}m$ in lower concentration groups treated with aqueous 10% phosphoric acid for 20s, 60s, 120s and 20% phosphoric acid for 20s. 5. The demineralization effect at the border of intertubular-peritubular junction was less evident than that in the peritubular and intertubular dentin. The collagen fibers in the intertubular dentin had a random orientation, whereas those that lined the tubules were circumferentially aligned. The cross-linkage of dentinal collagen in demineralized collagen layer was clearly seen. 6. A statistically significant difference of bond strengths according to the difference in phosphoric acid concentration did not exist among the groups treated with 10%, 20%, 30% and 40% acid solution (P>0.05). However, bond strengths to the treated dentin with 10% phosphoric acid solution for 30s were significantly higher than that for 120s (P<0.05).

• 한국세라믹학회지
• /
• 제18권3호
• /
• pp.192-200
• /
• 1981

This study deals with the low temperature ($25^{\circ}C$-$600^{\circ}C$) properties of Kaolin-Phosphate-water systems. Phosphoric acid, mono aluminum phosphate, mono ammonium phosphate, the mixture of phosphoric acid and mono aluminum phosphate, and the mixture of phosphoric acid and mono ammonium phosphate were used to characterize the M.O.R. of the systems with to quantity of phosphates, curing time, and firing temperature. Firing shrinkage, viscosity, surface tension, DTA, TGA, and X-ray diffraction patterns were also measured in order to investigated the factors of strengthening. The results of this study were summarized as follows: 1. The M.O.R. of kaolin-phosphate systems were stronger than that of Kaolin-water system at room temperature or low temperature($25^{\circ}C$-$600^{\circ}C$). Though it was increased according to the longer curing time, the higher temperature, and the more addition of phosphate, the M.O.R. were decreased in the case of 10 wt% phosphate addition in the system of phosphoric acid, mono aluminum phosphate and phosphoric acid-mono aluminum phosphate. 2. When the concentration of Phosphate was at 4 wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid was strongest among the specimens in added to the others phosphates. Whereas, when the concentration of phosphate was above 6wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid mono ammonium phosphate system cured at $25^{\circ}C$ was the strongest. 3. The M.O.R. of the specimen heated, in the temperature range of 15$0^{\circ}C$-1$600^{\circ}C$, and added to the mixture of phosphoric acid-mono aluminum phosphate system or phosphoric acid-mono ammonium phosphate system was stronger than that of specimen added to Phosphoric acid, mono-aluminum Phosphate or mono-ammonium phosphate alone. 4. The bonding force of phosphate binders was more closely related to surface tension than viscosity and it tended to be inversely proportional to surface tension. The bonding force after heating treatment seemed to be caused by the change of structure of phosphate according to heating.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.602-618
• /
• 1996

The purpose of this study was to investigate the effect of acid treatment of fluoride applied dentin surface with various concentrations of phosphoric acid for various periods of time on dentin bonding. Dentin specimens prepared from freshly extracted bovine mandibular anterior teeth were divided into fluoridated and nonfluoridated groups. Specimens of nonfluoridated group were pretreated with 10% phosphoric acid for 15 seconds. Those of fluoridated groups were treated with 2% sodium fluoride or 2% stannous fluoride solution for 5 minutes and stored in $37^{\circ}C$ distilled water for 3 days, followed by phosphoric acid treatment. The concentrations of phosphoric acid were 10%, 32% or 50% and the treatment periods of time were 15, 30 or 60 seconds. All the specimens were bonded with All Bond$^{(R)}$ 2 and Bisfil$^{TM}$ composite resin. After bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, tensile bond strengths of each specimens were measured and the pretreated dentin and the fractured dentin surfaces were examined under the scanning electron microscope. The results were as follows : The tensile bond strengths from the fluoridated groups were significantly lower than those from the nonfluoridated group when the concentrations of phosphoric acid and the treatment periods of time were equal in all the groups (p<0.05). In general, the higher the concentration of phosphoric acid and the longer the treatment period of time for acid etching on the fluoride applied dentin surface, the higher were the bond strength values. Recovery of bond strength of the dentin bonding agent was better in the NaF applied group than in the $SnF_2$ applied one. SEM findings of NaF applied and $SnF_2$ applied dentin surfaces demonstrated reaction product-covered and partially or completely obstructed dentinal tubules. SEM findings of dentin surfaces fluoridated for 5 minutes followed by etching showed wider tubular openings and more clean dentin surfaces when dentin was etched with higher concentration of phosphoric acid for longer period of time. On the SEM observations of the fractured dentin-resin interface, the etched specimens of fluoridated group showed an adhesive failure mode when the concentration of phosphoric acid and the treatment period of time were same as in the nonfluoridated group. As the concentration of phosphoric acid and the treatment period of time increase during acid etching, the cohesive failure area increased. However, excessive acid etching caused adhesive failure.

• 한국환경복원기술학회지
• /
• 제7권5호
• /
• pp.57-65
• /
• 2004

This study was carried out to measure the growth and photosynthesis of Iris pseudoacorus, the reduction rate of nitrogen(T-N) and phosphoric acid($P_2O_5$) from soils, and the increase rate of two substance into plants which cultivated at waterway soils of different concentration of two substance. The results are summarized as follows; 1. The contents of nitrogen and phosphoric acid at waterway soils of Mangyeong river showed the highest level in the around Samrye railway bridge where was located in the downstream and sewage of stock raising flowed in 2. The Iris pseudoacorus which cultivated at waterway soils showed the leaf and root growth of 43~50 and 9~13cm, respectively. And the growth was higher in the waterway soils contained high level of nitrogen The rate of photosynthesis was $3.5-5.9{\mu}mol\;m^{-2}s^{-1}$ ranges and this rate increased from the end of June to August and then decreased. The rate of photosynthesis was higher in waterway soils contained high nitrogen regardless of seasons. 4. The Iris pseudoacorus removed nitrogen and phosphoric acid from waterway soils about 19~21% and 13~15%, respectively. The Iris pseudoacorus was effective to remove nitrogen more than phosphoric acid. And the waterway soil which included high concentration of two substance showed highly removal 5. The results of Iris pseudoacorus vegetation in the waterway soils showed that nitrogen and phosphoric acid of inside plant increased with 0.2-1.0% and 0.01-0.10% ranges, respectively. The contents of nitrogen and phosphoric acid in plants were increase in the soils of higher contents of nitrogen and phosphoric acid, and the rate of increase of nitrogen and phosphoric acid was higher at roots than leaves.

• 한국환경복원기술학회지
• /
• 제14권6호
• /
• pp.17-27
• /
• 2011

Prunus serrulata var. serrulata f. spontanea (E. H. Wilson) C. S. Chang was treated with dried swine excrement at various concentration levels, and their growth reactions and the contents of total kjeldahl nitrogen and total phosphoric acid were analyzed. The result is as follows; 1. When the plants were treated with 0.25% of dried swine excrement, the seed germination rate of Prunus serrulata var. serrulata f. spontanea was higher than that of the control. However, it showed a tendency to decrease when the treatment concentration got higher than 0.25%. 2. The growth rate of species was highest when they were treated with 0.25% of dried swine excrement. It tended to decrease with higher treatment concentration than 0.25%. Significant difference was clear between the control and the experimental plants of Prunus serrulata var. serrulata f. spontanea. 3. The contents of nitrogen and phosphoric acid in Prunus serrulata var. serrulata f. spontanea also got higher as the concentration of dried swine excrement increased. However, the content of total kjeldahl nitrogen was highest in the leaves, and followed by the roots and stems. In contrast, the content of total phosphoric acid were highest in the roots, and followed by the leaves and stems. Therefore, stems had the lowest contents of both nitrogen and phosphoric acid. 4. The contents of total kjeldahl nitrogen and total phosphoric acid in the soil were measured before and after the growth experiment of Prunus serrulata var. serrulata f. spontanea treated with dried swine excrement. The contents of nitrogen and phosphoric acid significantly decreased after the experiment. In conclusion, the contents of total kjeldahl nitrogen and total phosphoric acid accumulated in the plants increased as the concentration level of dried swine excrement got higher. The seed germination and plant growth rates were best at 0.25% treatment of dried swine excrement. The treatment of dried swine excrement may bring high effects on increasing the plant growth rate but could damage the plants with higher concentration than they need. Different optimal concentration levels of dried swine excrement for different plants should be found before it is used as fertilizer.

• 자원리싸이클링
• /
• 제14권5호
• /
• pp.18-23
• /
• 2005

초산, 질산, 인산이 함유된 폐혼산으로부터 인산을 분리하여 재활용하기 위한 방법으로 용매추출법을 이용하였다. 폐혼산에서 초산과 질산을 선택적으로 분리하고, 추출 잔류액에서 인산을 회수하고자 하였다. 주요 실험 변수로는 추출제 농도, 교반시간, 교반속도 등의 변화에 따른 초산, 질산, 인산의 추출거동을 조사하였다. 또한, McCabe-Thiele diagram으로부터 초산, 질산 성분의 추출 및 탈거에 필요한 이론적 단수를 조사하였다. 실험결과 인산염계 추출제를 사용할 경우 초산과 질산을 선택적으로 분리 추출이 가능하였으며, 추출제의 함량은 유기상의 50%가 적합하였다. 교반속도와 교반시간의 영향은 크게 없었으며, 상비(A/O)=1/3, 6단에서 초산과 질산을 완전히 추출 분리하여 인산을 추출잔류액에서 회수가 가능하였다.

• 분석과학
• /
• 제14권1호
• /
• pp.34-43
• /
• 2001

수소화물생성법-유도결합플라스마-원자방출분광법으로 게르마늄을 분석할 때 보조산으로 phosphoric acid의 사용은 nitric acid, hydrochloric acid, sulfuric acid, perchloric acid, boric acid, tartaric acid, malic acid, oxalic acid, acetic acid, tannic acid, citric acid의 사용보다 높은 수소화물 생성효율을 보였고, 같은 pH영역이라도 phosphate ion이 존재하는 buffer의 사용이 더 높은 생성효율을 보였다. 또한, 2.5M phosphoric acid를 이용한 결과, 시료용액 내에 잔류하는 산이나 공존원소의 영향이 감소하였다. 환원제와 안정제의 농도가 증가할수록 수소화물 생성효율은 증가되었으며, 최대방출세기를 나타내는 산의 세기는 높은 쪽으로 이동했고 농도영역은 넓어졌다. 인산 존재 하에서의 게르마늄의 검출한계는 $0.03{\mu}g/L$이었다.

• 대한치과교정학회지
• /
• 제25권3호
• /
• pp.341-353
• /
• 1995

이 연구는 부식농도가 전단결합강도와 법랑질 표면의 부식깊이에 미치는 영향을 관찰하기 위하여 표면을 편평하게 연마한 소의 법랑질을 $0%,\;5%,\;10%,\;20%,\;30%,\;40%,\;50%,\;60%,\;70%,\;80%$ 및 $85\%$ 인산용액으로 60초간 부식시키고, 브라켓 접착의 전단결합강도와 법랑질 표면의 부식깊이와 조도를 측정하고, 주사전자현미경으로 부식면을 검경하였으며, 이상에서 얻은 자료를 통계처리하고 평가하여 다음과 같은 결론을 얻었다. 법랑질 표면의 부식깊이는 인산액의 농도가 $40\%$ 내지 $50\%$에 도달할 때까지 증가하다가 그 이후의 농도증가와 함께 점진적으로 감소하였다. 법랑질 표면의 부식깊이와 부식면의 조도 사이에 상관성이 없었으며, 부식면의 조도와 전단결합강도 사이에 중등도의 상관성($\gamma$=0.63)을 보였다. 인산액의 농도가 $5\%$에서 $40\%$에 도달할때까지 균질의 편평한 부식면을 나타내는 소견을 보였으나 $50\%$와 $60\%$에서 불균질의 과도한 그리고 편평하지 못한 부식면소견을 보였으며, $10\%$에서 $60\%$까지의 인산액에 의한 법랑질 부식 후 레진 접착제의 전단결합강도 사이에는 유의차가 얼었으며, $5\%$와 $70\%$의 인산액에 의한 것은 전자보다 작았으나 구강내에서 교정력에 견딜수 있는 전단결합강도를 나타낼 것으로 추정된다.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.559-568
• /
• 1996

The purpose of this study was to evaluate the micro leakage of composite resin when various phosphoric acid agents were used to etch the enamel and dentin. In this study, class V cavities were prepared on the buccal surfaces of fourty extracted human molar teeth, and they were randomly assigned into 4 groups with 10 teeth. The cavities of each groups were etched with 10%, 32%, 35% and 37% phosphoric acids for 15 seconds, washed and dried and the cavities were restored with composite resin after application of the adhesive. The specimens were immersed in 2% methylene blue solution for 3 days. And then, the specimens were sectioned buccoligually. Degree of dye penetration at tooth-restoration interfaces was examined by Inverted Metallurgical Microscope at the occlusal and gingival margins. The result were as follows : 1. The degree of microleakage at occlusal and gingival margin in all group was statistically difference among 10% and 35% (P<0.01), 10% and 37% (P<0.01), 32% and 35% (P<0.05) and 32% and 37% (P<0.05) acid concentrations, but was not statistically difference between 10% and 32%, 35% and 37% acid concentrations (P>0.05). The degree of microleakage was showed to dimish with increase of acid concentration. 2. The degree of microleakage at the occlusal margin was statistically significant difference among 10% and 32%,10% and 35%, 10% and 37% acid concentrations(P<0.05). The degree of microleakage among 32% and 35%, 32% and 37% and 32% and 37% acid concentrations was not statistically significant difference. 3. In comparison of microleakage at the gingival margin, the degree of microleakage above 32% acid concentration was not showed less than 10% acid concentration (P>0.05). In comparison of 32%, 35%, 37% acid concentrations, the degree of microleakage at 35% and 37% acid concentrations was showed less than 32% acid concentration(P<0.05).