• Journal of Electrical Engineering and Technology
• /
• v.12 no.3
• /
• pp.1090-1100
• /
• 2017

This paper presents the comparison of starting current characteristics of a three-phase induction motor fed by two types of soft starters. The first soft starter under investigation is a conventional AC voltage controller on the basis of a phase-control technique. The other is the proposed asynchronous PWM AC chopper which is developed from the conventional synchronous PWM AC chopper. In this paper, the proposed asynchronous PWM AC chopper control scheme is developed by generating only two asynchronous PWM signals for a three-phase main power circuit (6 switching devices) from a single voltage control signal which is compared with a single sawtooth carrier signal. By this approach, the PWM signals are independent and easy to implement since the PWM signals do not need to be synchronized with a three-phase voltage source. Details of both soft starters are discussed. The experimental and simulation results of the starting currents are shown. It is found that the asynchronous PWM AC chopper efficiently works as a suitable soft starter for the three-phase induction motor due to that the starting currents are reduced and are sinusoidal with less harmonic contents, when being compared with the starting current waveforms using the conventional phase-control starting technique. Also the proposed soft starter offers low starting electromagnetic torque pulsation.

• Korean Journal of Applied Biomechanics
• /
• v.30 no.1
• /
• pp.7-16
• /
• 2020

Objective: It is to find factors related to stability through analysis of plantar pressure factors according to the level of instability when performing Snatch. Method: Foot pressure analysis was performed while 10 weightlifters performed 80% of the highest level of Snatch, and motion was classified and analyzed in 3 grades according to the level of instability. Results: First, in Bad Motion, the movement distance of the pressure center in the direction of ML and AP was larger significantly in Phase 2. Second, in Phase 2, the number of zero-crossing in the AP direction was larger statistically significantly in Good Motion. Third, in the bad motion in Phase 3, the number of zero-crossing in the ML direction showed a significantly larger value. Fourth, in Phase 4, it was found that the more stable the lock out motion, the greater the activity of foot controlling in the left and right directions. Fifth, Phase 3, the greater the Maximum/Mean foot pressure value, the more stable the pulling action. Sixth, in Phase 2, the foot pressure was concentrated with a wide distribution in the midfoot and rearfoot. Seventh, the triggering number of the forefoot region was small in the last pull phase. Eighth, the number of triggers in the toe area was significantly higher during Good Motion in Phase 4. Conclusion: Summarizing the factors of instability in Snatch, there was no significant difference in Phase 1 for each condition. In order to enhance the stability in Phase 2, the sensory control ability in the AP direction is required, and focusing the foot pressing motion with a wide distribution in the middle and rear parts increases the instability. In Phase 3, it was found that the more unstable, the more sensory control activity was performed in the ML direction, the stronger the forefoot pressing action should be performed for a stable Snatch. In Phase 4, It is important that the feet sensory control activity in ML directions and the control ability of the toes in order to have stable Lock out motion.

• Biomedical Science Letters
• /
• v.5 no.1
• /
• pp.67-74
• /
• 1999

To investigate the effect of the circadian variations on the toluene metabolism, 50％ toluene in olive oil (0.2 m1/100 g body weight) was intraperitoneally administered to the rats every other day for 6 days both in the night; 24:00 and the day; 12:00. Each group of animals was sacrificed at 8 hr after last injection of toluene. Hepatic microsomal aniline hydroxylase activity was more increased in control rats of night phase than those of day phase. On the other hand, the activities of hepatic benzylalcohol dehydrogenase in control rats of night phase showed the similiar value with that in those of day phase and in case of toluene treatment, these enzyme activities in rats of night phase were rather more decreased than those of day phase. Furthermore, hepatic benzaldehyde dehydrogenase activities were more or less higher in the control rats of night phase than those of day phase and by toluene treatment, enzyme activities of rats of night phase were somewhat decreased than those of day phase. in vitro, benzylalcohol or benzaldehyde inhibited the activities of benzylalcohol or aldehyde dehydrngenase prepared from the rats liver supematant. There were no differences in urinary hippuric acid contents between the night phase and day phase both in the control and toluene treated group. The increasing rate of liver weight per body weight (％), serum xanthine oxidase activities were higher in rats of night phase than in those of day phase by toluene treatment. In conclusion, these results indicate that the producing rate of benzylalcohol and benzaldehyde from toluene may be higher in rats of night phase than those of day phase.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.3
• /
• pp.231-239
• /
• 2017

A novel current control technique with fast response and application in an unbalanced system is proposed in this paper. Contrary to the conventional PI and dead-beat current control techniques, the proposed method is adopted to the valley current mode control (VCMC) and average current mode control (ACMC) methods to overcome the phase delay caused by conventional methods. The advantages of the proposed system are simplicity of structure and ease of implementation. The VCMC and ACMC methods are established and applied to the buck converter, boost converter, three-phase PWM converter, and three-phase inverter. The control performances of the proposed systems are shown by computer simulations and verified by experimental results.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.954-960
• /
• 2020

This paper proposes a speed variable proportional resonant current control method for a single-phase permanent magnet synchronous motor(PMSM). Due to the electromagnetic characteristics of a single-phase PMSM, negative and zero torques are generated in the part corresponding to the phase difference between the stator current and the back electromotive force. In addition, overcurrent limitation is required because of the low stator resistance and inductance in sensorless operation. When using the vector control for current control of single-phase PMSM under these conditions, processes of coordinate transformation, inverse coordinate transformation, and generation of virtual dq-axis components are required. However, the proposed variable speed proportional resonant current control method does not need the coordinate transformation used for AC motors. In this paper, we have confirmed stable maneuverability by using variable proportional resonant current control algorithm, and proposed sensorless control based on a mathematical model of a single-phase PMSM without a position sensor when reaching a constant speed. The usefulness of the current control method was verified through several experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.129-135
• /
• 2010

It is well known that distributed generation(DG) system using renewable energy is an alternative to solve the problems which result from the exhaustion of fossil fuel and the environmental pollution. A PWM inverter is required for a power flow control in the DG systems. This paper proposes a SRF power flow control method considering grid impedance in grid-connected single-phase inverter systems. The proposed SRF power flow control method can provide a voltage-reference for the single-phase inverter even without any grid impedance estimation so that the single-phase inverter system could operate in stand-alone mode and grid-connected mode based on the known nominal value of grid impedance. Also independent controls of active and reactive power are achieved by the proposed control method. The effectiveness and the validity of the proposed control method are demonstrated through simulations. The simulation results show that the proposed control method can control properly power flow in grid-connected single-phase inverter systems.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.12
• /
• pp.541-554
• /
• 1986

This paper presents the results of driving performance analysis of permanent magnet synchronous motor using a microprocessor based control system. The system consists of three phase power transistor inverters, three phase controlled rectifier, three central processing units, and sensors. The three CPUs are, respectively, used to generate PWM control signals for the inverter generating three phase sine wave, to generate the gate control signals for firing the converter, and to supervise other two CPUs. The supervisor is used to compute PI control algtorithm to three phase reference sine wave for the inverter. It is also used to maintain a constant voltage frequency ratio for the converter operating as a constant torque controller. The inverter CPU retrieves precomputed PWM patterns from look up tables because of computation speed limitations found in almost available microprocessors. The converter CPU also retrieves precomputed gate control patterns from another look-up tables. For protecting the control ststem from any damage by extraordinary over currents, the supervisor receives the data from current sensor, CT, and break down the CB to isolate the circuits from source. A resolver has a good performance characteristics of overall speed range, especially on low speed range. Therefor the speed control accuracy is impoved. The microprocessor based PM synchronous motor control system, thus, has many advantages such as constant torque characteristics, improvement of wave, limitation on extraordinary over currents, improvement of speed control accuracy, and fast response speed control using multi-CPU and look-up tables.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1438-1454
• /
• 2016

Because the nonlinear and time-varying characteristics of continuously variable transmission (CVT) systems driven by means of a six-phase copper rotor induction motor (CRIM) are unconscious, the control performance obtained for classical linear controllers is disappointing, when compared to more complex, nonlinear control methods. A blend modified recurrent Gegenbauer orthogonal polynomial neural network (OPNN) control system which has the online learning capability to come back to a nonlinear time-varying system, was complied to overcome difficulty in the design of a linear controller for six-phase CRIM driving CVT systems with lumped nonlinear load disturbances. The blend modified recurrent Gegenbauer OPNN control system can carry out examiner control, modified recurrent Gegenbauer OPNN control, and reimbursed control. Additionally, the adaptation law of the online parameters in the modified recurrent Gegenbauer OPNN is established on the Lyapunov stability theorem. The use of an amended artificial bee colony (ABC) optimization technique brought about two optimal learning rates for the parameters, which helped reform convergence. Finally, a comparison of the experimental results of the present study with those of previous studies demonstrates the high control performance of the proposed control scheme.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.974-986
• /
• 2015

A novel inverter fault-tolerant control scheme is proposed to drive brushless DC motor. A fault-tolerant inverter and its three fault-tolerant schemes (i.e., phase A fault-tolerant, phase B fault-tolerant, and phase C fault-tolerant) are analyzed. Eight voltage vectors are summarized and a voltage vector selection table is used in the control scheme to improve the midpoint current of the split capacitors. A stator flux observer is proposed. The observer can improve flux estimation, which does not require any speed adaptation mechanism and is immune to speed estimation error. Global stability of the flux observer is guaranteed by the Lyapunov stability analysis. A novel stator resistance estimator is incorporated into the sensorless drive to compensate for the effects of stator resistance variation. DC offset effects are mitigated by introducing an integral component in the observer gains. Finally, a control system based on the control scheme is established. Simulation and experiment results show that the method is correct and feasible.

• Journal of the Korean Society of Physical Medicine
• /
• v.4 no.3
• /
• pp.193-200
• /
• 2009

Purpose：In this study is to verify the effects postural control training based on Bobath approach for body schema and visual perception on Middle Cerebral Artery(MCA) Infarcts. Methods：The subject was a 46 years old man with MCA infaction, lives in B city. An AB design for a single-subject research was used for this study. The procedures consisted of 1 time of baseline phase(A), 20 times of treatment phase(B). We applied the Bobath approach at the subject. Treatments included to facilitate trunk alignment and stability, and to train weight bearing and shifting, to facilitate pelvis movement, and to train walk especially stance phase and assist up-down stairs locomotion in environment similar to actual daily life. Results：With this treatment, the majority of body schema and visual perception and postural control was improved in treatment phase compared with in baseline phase. Therefore, this study supported the effectiveness of postural control training based on Bobath approach for body sechma and visual perception of hemiplegia. Conculusion：This study is integrated postural control training with Bobath approach that are widespread for hemiplegia and measured outcomes based on individualized therapy goals. Consequently the study is suggested the meaning of quality effectiveness of Bobath approach.