• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.843-852
• /
• 2009

In this paper, we present design, fabrication, and measured results for a frequency upconverter for a wireless communication system of UAV(Unmanned Aerial Vehicle). The specifications of such wireless communication system requires the special features of maximum range of communication as well as deployment in UAV and repairing. The frequency upconverter operating at $5.25{\sim}5.45\;GHz$ in C-band was designed and fabricated considering such special features. The AGC function was included because the required output power should be constant for optimal system operation. The fabricated upconverter showed a constant output power of $+2{\pm}0.5\;dBm$ for the $-15{\sim}-10\;dBm$ input. Spuriouses were below -60 dBc and the adjacent leakage power was below -40 dBc. In addition, LO sources in the upconverter was implemented using the frequency synthesizer with step 1 MHz. This is for the application to the situation where multiple UAVs employed and the possible change of the permitted frequency band. The synthesizer showed a phase noise of -100 dBc/Hz at the 100 kHz frequency offset.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.5
• /
• pp.366-372
• /
• 2017

In this paper, the analysis of baluns that are inevitably required to design a differential low noise amplifier, The balun converts a single signal input from the antenna into a differential signal, which serves as an input to the differential amplifier. In addition, it protects the circuit from ESD(Electrostatic Discharge) coming through the antenna and helps with input matching. However, in the case of a passive balun used in general, since the AC signal is transmitted through electromagnetic coupling formed between two metal lines, it not only has loss without gain but also has the greatest influence on the total noise figure of the receiving end. Therefore, the design of a balun in a low-noise amplifier is very important, and it is important to design a balun in consideration of line width, line spacing, winding, radius, and layout symmetry that are necessary. In this paper, the factors to be considered for improving the quality factor of balun are summarized, and the tendency of variation of resistance, inductance, and capacitance of the balun according to design element change is analyzed. Based on the analysis results, it is proved that the design of input balun allows the design of low noise, high gain differential amplifier with gain of 24 dB and noise figure of 2.51 dB.

• Journal of The Korean Association For Science Education
• /
• v.36 no.6
• /
• pp.815-833
• /
• 2016

This study investigated children's (grade 3 to 9) responses to assessment items on energy as a cross-cutting concept in order to get basic information for a learning progression. The assessment consisted of 8 ordered multiple-choice items at the contexts of electric circuit, mechanical energy of falling objects, phase change of matter, dissolution, biological phenomena of a lizard, food chain, radiative equilibrium between Sun and Earth, and the system of water cycling. Children's responses to each item were analyzed with using cross-tabulations in terms of grades and item option levels and Wright map and Differential item functioning based on Rasch modeled item response analysis. The results offered empirical evidence of children's development of understanding energy from relation between energy and its phenomena, types of energy, transfer and conversion of energy, towards conservation and equilibrium of energy for all of eight contexts. Children of each grade did not fully understand energy conservation. As grade goes up, their understandings of energy transfer and conversion were differentiated across the contexts and topics of energy. According to Rasch analysis, children had easier understanding of energy on dissolution and poorer understanding of energy on water cycling than that on other contexts. It was discussed and suggested that the results of this study help us organize science topics with regard to energy when developing new national science curriculum.

• Korean Journal of Construction Engineering and Management
• /
• v.14 no.6
• /
• pp.49-60
• /
• 2013

Evacuation process has been considered as one of the most important elements to be managed in public facilities. Although the importance is highlighted through numerous literatures, disaster evacuation planning, particularly fire accidents, faces a number of human behavior related limitations for a similar application to different types of facilities/occupants. To overcome the obstacles including complexity in human behaviors, a number of simulation techniques with limited consideration on human behaviors are utilized to predict foreseeable problems in evacuation process. Therefore, this research aims to propose system dynamics models incorporating human behaviors considering different types of occupants under disaster evacuation events. Analysis on emergent human behaviors such as group forming and interactions under urgent situation are conducted based on the main stream theories in social science field. The results suggest the influences of human behavior factors including cooperative intention, information sharing, and mobility change to evacuation behavior. The implications are expected to provide safety consideration at planning/designing phase of buildings and help facility safety managers for evacuation planning with more realistic management approaches.

• Journal of Korean Society of Forest Science
• /
• v.9 no.1
• /
• pp.49-54
• /
• 1969

As one phase of the biological control of the Pine gall-midge, Thecodiplosis japonensis Uchida et Inouye, this investigation on birds as a vertebrte predator of the larvae of Pine gall-midge was carried out. Species of the birds as predator, number of the larvae as prey for individual birds and seasonal trends of the prey quantity were studied. This work was carried out during the late fall of 1967 and 1968 at Kwang Nueng Forest which is one of the heavily infested districts by the Pine gall-midge. 1. Korean Great-Tit, East China Marsh-Tit, Quelpart Coal-Tit, White-headed Long-tailed Tit, Varied Tit, Kamchatkan Rustic Bunting, Yellow-thrated Bunting, Chestnut Bunting and Korean Goldcrest were found to be the predator of the larvae of Pine gall-midge. 2. The average number of larvae as prey found from individual predator bird species were approximatly 108 for Kamchatkan Rustic Bunting, 17-64 for East China Marsh-Tit, 25-28 for Korean Great Tit and 36 for Quelpart Coal Tit. 3. The seasonal change in the number of the larvae which fell into the ground affected the seasonal trends of the prey quantity of the predator birds 4. Among the 380 birds examined, 157 birds were found to attack the larvae of Pine gall-midge.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.57-63
• /
• 2012

$Al_2TiO_5$ ceramics were sintered by a solid-state reaction. LAS (${\beta}$-spodumene) and $Fe_2O_3$ were added to the $Al_2TiO_5$ composition for enhancement of sintering behavior such as mechanical strength and thermal shock resistance. The sintered body was much densified by addition of LAS and $Fe_2O_3$ because LAS formed the liquid-phase and $Fe_2O_3$ suppressed the grain growth. We have systematically investigated the sintering characteristics, microstructures, mechanical properties, and thermal shock resistance according to the change of the amount of additive. When the additive of LAS (20 wt%)-$Fe_2O_3$ was added to $Al_2TiO_5$, it confirmed that superior mechanical properties of the fracture strength of over 120 MPa and the thermal shock resistance of over $1,200^{\circ}C$ were achieved.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.10
• /
• pp.21-26
• /
• 2018

Soil-water characteristic curve, which is called soil retention curve, is required to explore water flows in unsaturated soils, relative permeability of water in multi-phase fluids flow, and change to stiffness and volume of soils. Thus, the understanding of soil-water characteristic curves of soils help us explore the behavior of soils inclduing fluids. Biopolymers are environmental-friendly materials, which can be completely degraded by microbes and have been believed not to affect the nature. Thus, various biopolymers such as deacetylated power, polyethylene oxide, xanthan gum, alginic acid sodium salt, and polyacrylic acid have been studies for the application to soil remediation, soil improvement, and enhanced oil recovery. PAA (polyacrylic acid) is one of biopolymers, which have shown a great effect in enhanced oil recovery as well as soil remediation because of the improvement of water-flood performance by mobility control. The study on soil-water characteristic curves of sandy soils containing PAA (polyacrylic acid) has been conducted through experimentations and theoretical models. The results show that both capillary entry pressure and residual water saturation dramatically increase according to the increased concentration of PAA (polyacrylic acid). Also, soil-water characteristic curves by theoretical models are quite well consistent with the results by experimental studies. Thus, soil-water characteristic curves of sandy soils containing biopolymers such as PAA (polyacrylic acid) can be estimated using fitting parameters for the theoretical model.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.410-416
• /
• 2004

In this study, we fabricated magnetite coated on a cordierite honeycomb which has complex shape by ultrasound-enhanced ferrite plating. The effects of the plating condition on the formation of the magnetite and its microstructure were investigated. The magnetite coated on the honeycomb became an oxygen-deficient ferrite by H$_2$ gas reduction, then the effects of the molar concentrations of ammonium acetate for $CO_2$ gas decomposition have been studied. As the molar concentration of a pH buffer($CH_3$COONH$_4$, 0.1946∼0.3892 M) solution increased, the average particle size increased about 200∼250 nm. The magnetite coated on the honeycomb was reduced by H$_2$ gas for 2 h at 30$0^{\circ}C$. The inner pressure change in the cell began to occur at 315∼34$0^{\circ}C$. The H$_2$-Reduced magnetite coated on the honeycomb at 35$0^{\circ}C$ contained an oxygen deficient magnetite and $\alpha$-Fe phase. The thermogravimetric analysis with H$_2$ reduction and $CO_2$ decomposition were carried out with the magnetite coated on the honeycomb. A weight loss in process of H$_2$ reduction occurred between 32$0^{\circ}C$ and 34$0^{\circ}C$, while a weight gain was observed during the $CO_2$ decomposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.35-36
• /
• 2008

PTC thermistor are characterized by an increase in the electrical resistance with temperature. The PTC materials of middle Curie point were produced or that of high Curie point (above $200^{\circ}C$), it was determined that compositional modifications of $Pb^{2+}$ for $Ba^{2+}$ produce change sin the Curie point to higher temperature. PTC ceramic materials with the Curie point above $120^{\circ}C$ were prepared by adding $PbTiO_3$, PbO or $Pb_3O_4$ into $BaTiO_3$. Thereby, adding $Pb^{2+}$ into $BaTiO_3$-based PTC material to improve Tc was studied broadly, however, weal know that PbO was poisonous and prone to volatilize, then to pollute the circumstance and hurt to people, so we should dope other innocuous additives instead of lead to increase Tc of composite PTC material. In order to prepare lead-free $BaTiO_3$-based PTC with middle Curie point, the incorporation on $Bi_{1/2}K_{1/2}TiO_3$ into $BaTiO_3$-based ceramics was investigated on samples containing 0, 1, 2, 3, 4, and 50mol% of $Bi_{1/2}K_{1/2}TiO_3$. $Bi_{1/2}K_{1/2}TiO_3$ was compounded as standby material by conventional solid-state reaction technique. The starting materials were $Bi_2O_3$, $K_2CO_3$, $BaCO_3$ and $TiO_2$ powder, and using solid-state reaction method, too. The microstructures of samples were investigated by SEM, DSC, XRD and dielectric properties. Phase composition and lattice parameters were investigated by X-ray diffraction.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.299-308
• /
• 2016

This paper presents an investigation of the mechanical and microstructural properties on hardened samples that were synthesized using blended binder(fly ash(FA) and blast furnace slag cement(BFSC)), alkali activator and sea water or distilled water. Binders were prepared by mixing the FA and BFSC in different blend weight ratios of 6:4, 7:3 and 8:2. Sodium hydroxide and sodium silicate were used 5 wt% of binder, respectively, as an alkaline activator. The compressive strength and absorption were measured at the age of 3, 7 and 28 days, and the XRD, TGA and MIP tests were performed at the age of 28 days. An increase in the content of BFSC leads to an increase in the quantities of ettringite and C-S-H formed, regardless of the type of mixing water. And it also shows higher strength due to the reduction of pores larger than ~50 nm. All hardened samples in this study have common hydration products of C-S-H, $Ca(OH)_2$ and calcite. Hydrocalumite of all reaction products formed was only present in hardened sample mixed with sea water. For each FA/BFSC mixing ratio, the compressive strength of hardened sample mixed with sea water was similar to that mixed with distilled water. It is proposed that the slight increase of strength of samples mixed with sea water is mainly due to the presence of hydrocalumite phase containing chlorine ion, contributing to the change of total porosity and pore size distribution in samples.