• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.5
• /
• pp.115-121
• /
• 2014

The intrinsic simplicity, ruggedness, and simple power electronic drive requirement of a Switched Reluctance Motor(SRM) make it possible to use in many commercial adjustable speed application. The simple magnetic circuit results in a high efficiency drive and low temperature rise, and the drive system provides a good drive characteristics. This paper is provides two phase 4/3 SRM that is similar to two phase 6/3 SRM as aspect to magnetic structure. Although 6/3 SRM does not experience any flux reversal as the flux is in the same direction whether phase A or B is excited, but two phase 4/3 SRM experiences a flux reversal in small part of stator yoke. The flux reversal in two phase 4/3 SRM could be relieved by an adjustment of stator yoke structure. The magnetic analysis and design considerations of the two phase 4/3 SRM have been obtained by the finite element method analysis (FEM).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.11-16
• /
• 2006

The object of this study is to develop new examination techniques for detecting the debonds in adhesive interface of different kinds of the material. Ultrasonic signal was modeled by theoretically analyzing ultrasonic propagation phenomenon of the adhesive interface and debonding interface. The test method using the phase reversal of the debonding interface applied to the FRP/Rubber test block. Aluminum/Rubber test block with the flat bottom hole was manufactured to quantitatively evaluate the minimum detection ability of the defects. The pulse echo reflection method and the phase reversal method were mutually compared and it was estimated that the phase reversal method could detect the debonds on the basis of the theoretically predicted ultrasonic signal and ultrasonic test data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.2
• /
• pp.9-16
• /
• 2009

The object of this study is to develop new examination technique for detecting debond in adhesive interface of different kinds of materials. Ultrasonic signal was modeled by theoretically analyzing ultrasonic propagation phenomenon of the adhesive interface and debonding interface. The test method using the phase reversal of the debonding interface applied to the FRP/Rubber test block. Aluminum/Rubber test block with the flat bottom hole was manufactured to evaluate quantitatively the minimum detection ability of defects. The pulse echo reflection method and the phase reversal method were mutually compared and it was estimated that the phase reversal method could detect the debond on the basis of the theoretically predicted ultrasonic signal and ultrasonic test data.

• Journal of the Optical Society of Korea
• /
• v.5 no.3
• /
• pp.76-82
• /
• 2001

The optical response for traveling-wave Mach-Zehnder modulators without-with phased reversal is successfully derived in more concise and succinct form than any other equations before. The obtained equation is applied to a bandpass traveling-wave modulator with 3-section phase reversal and is confirmed to be in reasonable agreement with the experimental data.

• Smart Structures and Systems
• /
• v.8 no.3
• /
• pp.303-320
• /
• 2011

Comparing to active damage monitoring, impact localization on composite by using time reversal focusing method has several difficulties. First, the transfer function of the actuator-sensor path is difficult to be obtained because of the limitation that no impact experiment is permitted to perform on the real structure and the difficulty to model it because the performance of real aircraft composite is much more complicated comparing to metal structure. Second, the position of impact is unknown and can not be controlled as the excitation signal used in the active monitoring. This makes it not applicable to compare the difference between the excitation and the focused signal. Another difficulty is that impact signal is frequency broadband, giving rise to the difficulty to process virtual synthesis because of the highly dispersion nature of frequency broadband Lamb wave in plate-like structure. Aiming at developing a practical method for on-line localization of impact on aircraft composite structure which can take advantage of time reversal focusing and does not rely on the transfer function, a PZT sensor array based phase synthesis time reversal impact imaging method is proposed. The complex Shannon wavelet transform is presented to extract the frequency narrow-band signals from the impact responded signals of PZT sensors. A phase synthesis process of the frequency narrow-band signals is implemented to search the time reversal focusing position on the structure which represents the impact position. Evaluation experiments on a carbon fiber composite structure show that the proposed method realizes the impact imaging and localization with an error less than 1.5 cm. Discussion of the influence of velocity errors and measurement noise is also given in detail.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.745-750
• /
• 2018

A Slot array antenna with a phase reversal device is presented for WLAN operation. The array factor and radiation characteristics of the antenna are investigated. For practical application of the radiation pattern, the phase reversal device is used. The antenna is formed on both sides of the substrate ($30mm{\times}96mm{\times}0.2mm$). The measured results show that the proposed antenna has a 10 dB return loss bandwidth of 156 MHz (2.392 - 2.548 GHz) and the measured maximum gain was 8.31 dBi.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.1
• /
• pp.515-520
• /
• 2020

The design and actual implementation of the four-bar parallel link was studied in the paper. The parallel four-section link is widely used as a basic kinematic mechanism for transmitting the rotation of one axis to the rotational motion of the other axis. However, the parallel 4 link has a problem that phase reversal occurs at the turning point during the movement. In order to prevent the link reversal, it is known that a double parallelogram-type link is formed by attaching an additional phase reversal suppression link with an offset. However, as a result of the actual fabrication experiment, the movement is not smooth at the transition point. In order to solve this problem, in this study, a link for smooth movement is added in addition to a link that provides an offset to prevent phase reversal, so that the phase reversal does not occur at a specific point when the driven shaft rotates along the drive shaft. The test result confirms the validity of our suggestion.

• Korean Journal of Optics and Photonics
• /
• v.12 no.4
• /
• pp.327-333
• /
• 2001

Estimation of the frequency response of Ti:LiNb03 traveling-wave optical modulator with phase reversal electrodes is succinctly presented. The fact that such devices may have bandpass characteristics is demonstrated through simulations based on the derived equations. The influence of each parameter of traveling-wave electrodes on the frequency response is investigated in detail. It is shown that the center frequency and the bandwidth of response curves can be effectively adjustable by changing the MW effective index and the interaction length of the electrodes. rodes.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.884-886
• /
• 2004

This paper introduces Flux-Reversal Machine(FRM) and presents the design of a single phase FRM to improve its starting torque. The effects of the design parameters on the characteristic and starting torque are analyzed by Finite Element Method(FEM). The considered design parameters are tapered airgap, stewed airgap, asymmetric PM width and slotted teeth. As a result, we can find the best model in producing starting torque of a single phase 2/3 FRM

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.866-868
• /
• 2004

The flux-reversal machine(FRM) is a new brushless doubly-salient permanent-magnet machine combining the advantages of the switched-reluctance machine(SRM) and the permanent-magnet machine(PMM) into one machine. FRM has a naturally low inductance, therefore, a low electrical time constant. This feature, combined with its simple construction and low rotor inertia appear to make the FRM attractive as a low-cost high-speed machine. For high-speed applications, two alternative commutation strategies are studied, one using the phase commutation advancing technique and another using the conducting pulse-width control. This paper describes the techniques and reports the corresponding simulated and experimented performance