• 비파괴검사학회지
• /
• 제26권3호
• /
• pp.162-168
• /
• 2006

Speckle interferometry with phase-shifting method has been applied to measurement of micro-scale displacement through optical signal processing. Four-step phase-shifting method by PZT is used to measure out-of-plane displacement in spot-welded cantilever and results of optical experiments are comparable to those of FEM. Phase-shifting method using Fourier transform by PZT is applied to measurement of in-plane displacement on rectangular steel plate with a circular hole. The results of optical experiment agree well with theoretical calculation. New phase-shifting method in speckle interferometry has been implemented with a quarter wave plate. In-plane displacement of specimen is measured by the new phase-shifting method. Results of optical experiment show that the quarter wave plate can be used for phase-shifting method that is cheap and easy to use in speckle interferometry.

• 비파괴검사학회지
• /
• 제30권6호
• /
• pp.527-538
• /
• 2010

This paper presents a nondestructive evaluation approach for system identification (SID) of real railway bridges using field vibration test results. First, a multi-phase SID scheme designed on the basis of eigenvalue sensitivity concept is presented. Next, the proposed multi-phase approach is evaluated from field vibration tests on a real railway bridge (Wondongcheon bridge) located in Yangsan, Korea. On the steel girder bridge, a few natural frequencies and mode shapes are experimentally measured under the ambient vibration condition. The corresponding modal parameters are numerically calculated from a three-dimensional finite element (FE) model established for the target bridge. Eigenvalue sensitivities are analyzed for potential model-updating parameters of the FE model. Then, structural subsystems are identified phase-by-phase using the proposed model-updating procedure. Based on model-updating results, a baseline model and a nondestructive evaluation of test bridge are identified.

• 비파괴검사학회지
• /
• 제30권4호
• /
• pp.352-358
• /
• 2010

전기적인 장치를 기반으로 한 테라헤르츠 송신기(terahertz transmitter; Tx)를 이용하여 0.34 THz의 전자기파를 발생시키는 소형 CW sub-THz 이미징 시스템을 제시하였다. Tx에 의해 발생된 0.34 THz의 전자기파를 point by point 스캔방식으로 샘플에 투과시켰고, 여기서 얻어진 데이터는 테라헤르츠 수신기(terahertz receiver; Rx)를 이용하여 진폭(magnitude)과 위상(phase) 정보로 측정한 후 이를 영상화하였다. 이 논문에서는 보다 좋은 이미지 해상도를 얻기 위하여 데이터 수집 시 이미지의 분해능(resolution)에 영향을 미치는 주사 스테이지(scanning stage)의 시간지연과 스텝거리를 변수로 두어 다양한 샘플들을 주사하여 그 결과를 측정, 비교하였다. 또한 플라스틱, 종이, 나무 등 다양한 샘플들의 이미징 측정을 통해 테라헤르츠 파의 응용 가능성을 확인하였다.

• 비파괴검사학회지
• /
• 제36권4호
• /
• pp.259-265
• /
• 2016

This paper presents a study on the use of pulsed phase thermography in the measurement of thermal barrier coating thickness with a numerical simulation. A multilayer heat transfer model was ussed to analyze the surface temperature response acquired from one-sided pulsed thermal imaging. The test sample comprised four layers: the metal substrate, bond coat, thermally grown oxide and the top coat. The finite element software, ANSYS, was used to model and predict the temperature distribution in the test sample under an imposed heat flux on the exterior of the TBC. The phase image was computed with the use of the software MATLAB and Thermofit Pro using a Fourier transform. The relationship between the coating thickness and the corresponding phase angle was then established with the coating thickness being expressed as a function of the phase angle. The method is successfully applied to measure the coating thickness that varied from 0.25 mm to 1.5 mm.

• 비파괴검사학회지
• /
• 제35권6호
• /
• pp.414-420
• /
• 2015

Concrete undergoes significant phase changes from liquid to solid states as hydration progresses. These phase changes are known as the setting process. A liquid state concrete is electrically conductive because of the presence of water and ions. However, since the conductive elements in the liquid state of concrete are consumed to produce non-conductive hydration products, the electrical conductivity of hydrating concrete decreases during the setting process. Therefore, the electrical properties of hydrating concrete can be used to monitor the setting process of concrete. In this study, a parameter identification method to estimate electrical parameters such as ohmic resistance of concrete is proposed. The effectiveness of the proposed method for monitoring the setting process of concrete is experimentally validated.

• 비파괴검사학회지
• /
• 제25권3호
• /
• pp.171-177
• /
• 2005

Phase-shifting method using Fourier transform (PSM/FT) has been applied to measurement of in-plane displacement of a specimen. Thirty-two interference fringe patterns each of which has different phase of ${\pi}/16$ radian have been gathered from a specimen with in-plane displacement. Low-pass filtering by 2-D Fourier transform is used to suppress spatial noise of the fringe patterns. ${\alpha}-directional$ Fourier transform for PSM/FT is performed by use of the low-pass filtered 32 fringe patterns. Two kinds of specimens are used for experiment. One is a rectangular steel plate and the other one is a rectangular steel plate containing a circular hole at the center. In-plane displacement of each specimen is measured by PSM/FT, and calculated by finite element method (ANSYS) for comparison. The results are quite comparable, so that PSM/FT can be applied to measurement of in-plane displacement.

• 비파괴검사학회지
• /
• 제30권3호
• /
• pp.181-193
• /
• 2010

The paper presents an alternative way to classical stereocorrelation. First, 2D image processing of random patterns is described. Sub-pixel displacements are determined using phase analysis. Then distortion evaluation is presented. The distortion is identified without any assumption on the lens model because of the use of a grid technique approach. Last, shape measurement and shape variation is caught by fringe projection. Analysis is based on two pin-hole assumptions for the video-projector and the camera. Then, fringe projection is coupled to in-plane displacement to give rise to 3D measurement set-up. Metrological characterization shows a resolution comparable to classical (stereo) correlation technique ($1/100^{th}$ pixel). Spatial resolution seems to be an advantage of the method, because of the use of temporal phase stepping (shape measurement, 1 pixel) and windowed Fourier transform (in plane displacements measurement, 9 pixels). Two examples are given. First one is the study of skin properties; second one is a study on leather fabric. In both cases, results are convincing, and have been exploited to give mechanical interpretation.

• 비파괴검사학회지
• /
• 제22권4호
• /
• pp.369-376
• /
• 2002

마이크로파 자유공간전송기법을 이용하여 생물자원인 곡류의 유전특성을 비파괴 방법으로 측정하였다. 마이크로파를 송신하고 수신할 수 있는 혼 안테나, 샘플홀더, network analyzer 를 이용하여 9.5 GHz에서의 마이크로파 측정 시스템을 구성하였다. 여러 가지 수분함량에서 산물밀도가 서로 다른 시료를 투과하여 나오는 마이크로파의 감쇠와 위상 변이로부터 유전상수와 유전손실을 측정하였다. 시료의 유전상수와 유전손실은 샘플홀더 내에 충진되는 시료의 수분함량과 산물밀도가 증가함에 따라 증가하였으며 수분함량과 산물밀도의 팝으로 표시되는 수분밀도를 이용할 경우 산물밀도와 시료 품종의 변이를 보정할 수 있는 것으로 나타났다.

• 비파괴검사학회지
• /
• 제35권6호
• /
• pp.398-406
• /
• 2015

This paper explored the results of experimental investigation on carbon fiber reinforced polymer (CFRP) composite sample with thermal wave technique. The thermal wave technique combines the advantages of both conventional thermal wave measurement and thermography using a commercial Infrared camera. The sample comprises the artificial inclusions of foreign material to simulate defects of different shape and size at different depths. Lock-in thermography is employed for the detection of defects. The temperature field of the front surface of sample was observed and analysed at several excitation frequencies ranging from 0.562 Hz down to 0.032 Hz. Four-point methodology was applied to extract the amplitude and phase of thermal wave's harmonic component. The phase images are analyzed to find qualitative and quantitative information about the defects.

• 비파괴검사학회지
• /
• 제37권2호
• /
• pp.75-83
• /
• 2017

In this paper, we investigate the capacity of the lock-in infrared thermography technique for the evaluation of non-uniform top layers of a silicon carbide coating with a nickel based superalloy sample. The method utilized a multilayer heat transfer model to analyze the surface temperature response. The modelling of the sample was done in ANSYS. The sample consists of three layers, namely, the metal substrate, bond coat and top coat. A sinusoidal heating at different excitation frequencies was imposed upon the top layer of the sample according to the experimental procedures. The thermal response of the excited surface was recorded, and the phase angle image was computed by Fourier transform using the image processing software, MATLAB and Thermofit Pro. The correlation between the coating thickness and phase angle was established for each excitation frequency. The most appropriate excitation frequency was found to be 0.05 Hz. The method demonstrated potential in the evaluation of coating thickness and it was successfully applied to measure the non-uniform top layers ranging from 0.05 mm to 1 mm with an accuracy of 0.000002 mm to 0.045 mm.