• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.2
• /
• pp.58-64
• /
• 2004

Most of the loads in industrial power distribution systems are balanced and connected to three power systems. However, in the user power distribution systems, most of the loads are single & three phase and unbalanced, generating voltage unbalance. Voltage unbalance is a condition in a polyphase system in which the rms values of the line-to-line voltages or the phase angles between consecutive line-to-line voltages, are not all equal. Slight voltage unbalance generates a disproportionately high current unbalance at the motor stator winding. This paper presents a scheme on operation states of a three-phase induction motor under unbalanced voltages. The three-phase voltages applied to the stator winding of the studied induction motor are controlled by respectively adjusting the magnitude and phase angle of each phase. The voltage unbalanced factor(VUF) of the three-phase source voltages can then be varied to examine the different values of VUF on machine's operation characteristics.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1046-1048
• /
• 2002

The increase of triplen harmonics in three-phase four-wire systems leads to overloaded neutral conductor, common-mode noise problems, derating of transformers, and so on. Various compensator has been designed to prevent the problems associated with the triplen harmonics. But these can not protect distribution system effectively because the triplen harmonic source is distributed extensively and distribution system type is diverse. This paper explain the operation and installation of single phase active power filter to eliminate triplen harmonics and then it is verified by simulation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.339-346
• /
• 2003

Molecular dynamic simulations of nano indentation on single-crystal silicon (100) surface were performed using diamond indentor. Silicon substrate and diamond indentor were modeled diamond structure with Tersoff potential model. Phase transformation of silicon, incipient plastic deformation, change of incident temperature distribution are investigated through the change of potential energy distribution, displacement-load diagram, the change of kinetic energy distribution and displacements of silicon atoms. Phase transformation is highly localized and consists of a high-density region surrounding the tip. Axial load linearly increased according to the indenting depth. Number of atoms with high kinetic energy increased at the interface between substrate and indentor tip.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.1
• /
• pp.31-37
• /
• 2006

The present study has been experimentally investigated the effect of geometric and operating parameters on the two-phase flow distribution of refrigerants in a horizontal T-junction. The operating parameters were the kind of refrigerants (R-22, R- l34a, and R-410A), saturated temperature, and the inlet mass flux and quality. The geometric parameters were the tube diameter and the tube diameter ratio. The measured data of refrigerants were compared with the values predicted using the models developed by several researchers for air/water or steani/water two-phase flow. Among the operating parameters, the inlet Quality was the most sensitive to the mass flow rate ratio. Between the geometric parameters, the tube diameter ratio was more sensitive than tube diameter.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.09a
• /
• pp.99-107
• /
• 1995

The Phase-type(PH) distribution, defined as a distribution of the time until the absorption in a finite continuous-time Markov chain state with one absorbing state, has been widely used for various stochastic modelling. But great computational burdens often make us hesitate to apply PH methods. In this paper, we propose a seemingly efficient approximation method for phase type distributions. We first describe methods to bound the first passage time distribution in continuous-time Markov chains. Next, we adapt these bounding methods to approximate phase-tupe distributions. Numerical computation results are given to verify their efficiency.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.27-31
• /
• 2007

Glass particle distribution in a stirred solid/liquid systems was investigated using computational fluid dynamics(CFD). The numerical results were compared to experimental data from the available literature which investigated the local dispersed phase volume fraction by means of an endoscope technique. Eulerian multi-phase model and applications considered high loading of solid particle was used to investigate the influence of the particle concentration and mixing tank size on the solid distribution. A good agreement was obtained between the experimental data and simulation results. The results showed different solid particle distribution in an agitator by particle concentration and mixer size.

• Journal of Mechanical Science and Technology
• /
• v.20 no.5
• /
• pp.717-727
• /
• 2006

The present study experimentally investigated the effect of flow direction and other flow parameters on two-phase flow distribution of refrigerants at a T-junction, and also suggested a prediction model for refrigerant in a T-junction by modifying previous model for air-water flow. R-22, R-134a, and R-410A were used as test refrigerants. As geometric parameters, the direction of the inlet or branch tube and the tube diameter ratio of branch to inlet tube were chosen. The measured data were compared with the values predicted by the models developed for air-water or steam-water mixture in the literature. We propose a modified model for application to the reduced T-junction and vertical tube orientation. Among the geometric parameters, the branch tube direction showed the biggest sensitivity to the mass flow rate ratio for the gas phase, while the inlet quality showed the biggest sensitivity to the mass flow rate ratio among the inlet flow parameters.

• Carbon letters
• /
• v.13 no.3
• /
• pp.133-138
• /
• 2012

According to kinetic mechanisms, liquid phase polymerization and solid phase polymerization are different in acrylonitrile (AN) polymerization, and so the relationship between the contribution ratio and molecular weight distribution (MWD) was obtained through theoretic analysis. The precipitation homopolymerization of AN was carried out in a mixture solution of dimethyl sulfoxide (DMSO) and water at $50{\sim}65^{\circ}C$ using ${\alpha}$,${\alpha}^{\prime}$-azobisisobutyronitrile as an initiator. The contribution ratio decreased and approached 0; the MWD also decreased and approached 2 with the increase of the $H_2O$/DMSO ratio from 10/90 to 90/10. The experimental data were found to coincide well with the theoretical equation derived from the mechanisms.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.2
• /
• pp.121-130
• /
• 2021

In this study, a computational fluid dynamics (CFD) simulation based on an Eulerian-Eulerian approach was used to evaluate the mixing performance of a mud agitator through the distribution of bulk particles. Firstly, the commercial CFD software Star-CCM+ was verified by performing numerical simulations of single-phase water mixing problems in an agitator with various turbulence models, and the simulation results were compared with an experiment. The standard model was selected as an appropriate turbulence model, and a grid convergence test was performed. Then, a simulation of the liquid-solid multi-phase mixing in an agitator was simulated with different multi-phase interaction models, and lift and drag models were selected. In the case of the lift model, the results were not significantly affected, but Syamlal and O'Brien's drag model showed more reasonable results with respect to the experiment. Finally, with the properly determined simulation conditions, a multi-phase flow simulation of a mud agitator was performed to predict the mixing time and spatial distribution of solid particles. The applicability of the CFD multi-phase simulation for the practical design of a mud agitator was confirmed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.466-469
• /
• 2002

In the sintering of YIG, abnormal grain growth phenomena was observed. This abnormal grain growth is related to the sintering temperature in this experiment. In the sintering below 145$0^{\circ}C$., the sintered body showed narrow size distribution. However, in the sintering at 145$0^{\circ}C$, a few grains grew rapidly with respect to other grains, and bimodal size distribution was appeared. Liquid phase was not observed far from the abnormally grown large grains, but only near the large grains. This means that the abnormal grain growth was caused by the nonuniform distribution of liquid phase which promote the grains growth. This nonuniform distribution of liquid phase was thought to be due to the nonuniform mixing of the starting materials. This abnormal grain growth was suppressed by enhance the compositional uniformity by multiple calcination.