• 한국정보통신설비학회:학술대회논문집
• /
• 2004.08a
• /
• pp.386-389
• /
• 2004

This thesis complemented the weak points that the existing theses did not represented a phase characteristic as the equivalent circuit by applying 4-port simulation to DGS (Defected Ground Structure) characteristic and an equivalent circuit, which are the transmission line structure that has the defect made in the ground surface. We used a distribute device and a lumped device, obtained the equivalent circuit by applying the structure of balun to a discontinuous part. An indicated DGS (Defected Ground structure) is a dumbbells-shaped single defect, we indicated satisfying a magnitude and phase characteristics by applying this equivalent circuit.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.336-340
• /
• 1998

In this paper, an effective control scheme of a single phase UPS inverter is proposed to have no steady state error of the output voltage and the fast response for the load request. The cosine wave tranfer function is proposed to control the output voltage. This controller clearly removes errors of magnitude and phase both in the steady state. On the other hand, a current controller is proposed to reduce the transient time of the voltage control and to improve the bad distorted factor of the output voltage waveform by the load fluctuation and the presences of nonlinear parameters in the plant. The current controller is designed parallel to the voltage controller and performs separately from it.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.163-165
• /
• 1999

This work presents the performance characteristic of digital watthour meter under the harmonics of voltage and current. Each waveform involved is different in magnitude phase, and THD(Total Harmonic Distortion). It is possible to generate harmonics and control those waveforms using RTDS(Real Time Digital Simulator). Tests were performed on a selected sample of three-phase digital watthour meter which is coupled with data acquisition system via RS 485/232 converter. The percentage error rate of the watthour meter is compared for both sinusoidal and nonsinusoidal cases and the results are given.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.569-576
• /
• 1997

Electrically-induced strain and polarization studies of the (1-x)Pb(Mg1/3Nb2/3)O3-PbZrO3 crystalline solutions have been done. Dielectric constants with temperature were investigated for 0$\leq$x$\leq$0.95. With increasing PbZrO3 content the transition maxima were found to move to higher temperature region and DPT (Diffused Phase Transition) properties were decreased for x$\leq$0.60. Phase transition between ferroelectric states and antiferroelectric states was confirmed for 0.93$\times$10-3 for 0.4

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3C
• /
• pp.264-270
• /
• 2003

Application of the Filtered-X LMS adaptive filter to active noise control requires to estimate the transfer characteristics between the output and the error signal of the adaptive canceler. In this paper, we derive an adaptive control algorithm and analyze its convergence behavior when the acoustic noise is assumed to consist of multiple sinusoids. The results of the convergence analysis of the Filtered-X LMS algorithm indicate that the effects of parameter estimation inaccuracy on the convergence behavior of the algorithm are characterize by two distinct components : Phase estimation error and estimated magnitude. In particular, the convergence of the Filtered-X LMS algorithm is shown to be strongly affected by the accuracy of the phase response estimate. Simulation results of the algorithm are presented which support the theoretical convergence analysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.2000-2004
• /
• 2009

In general, for the condition monitoring of a power transformer using the UHF PD measuring technique, detection of any partial discharge, identifying the defect in the transformer and locating the insulation defect are necessary. In this paper one of the most frequent detects which can result in turn to turn fault in power transformer was examined for identifying the defect. In order to model the defect, as a discharge source, a partial discharge cell was used for experimental activity. Magnitude of electromagnetic wave signals and corresponding amount of apparent discharge were measured simultaneously against phase of applied voltage to the discharge cell. Frequency range and phase resolved partial discharge signals were measured and analyzed. The results will be contributed to build the defect database of power transformer and to decrease the occurrence of transformer faults.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1095-1097
• /
• 1993

The double excited induction motor has two sets of three-phase system : One is connected to the ac source to take care of energy convertion, and the other is to the inverter controlable frequency and/or magnitude of voltage, both of the induction mode and the synchronous mode are possible in double excitation motor, and the proposed double excitation motor can be driven as a synchronous motor by the extra three-phase input. At the synchronous mode the efficiency is improved so higher than that at induction mode or induction motor. The rating of the inverter used for speed control can be reduced upto one-fifth of that for conventional induction motor. Also the cost and maintenance fee of double excitation induction motor can be reduced compared to any other motors.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.293-296
• /
• 2008

Injection molding operation consists of filling, packing, and cooling phase. The highest pressure is involved during the packing phase among the operation phases. Cavity pressure depends upon velocity to pressure switchover time and magnitude of packing pressure. The cavity pressure is directly related to stress concentration in the cavity of mold. Thus the observation and control of cavity pressure is very important to prevent mold cracking. In this study, cavity pressures were observed for operational conditions using the commercial CAE software, Moldflow. Operational conditions were velocity to pressure switchover time and packing pressure. Cavity pressures were also measured directly during injection molding. Simulation and experimental results showed good agreement.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2043-2045
• /
• 2004

This thesis complemented the weak points that the existing theses did not represented a phase characteristic as the equivalent circuit by applying 4-port simulation to DGS (Defected Ground Structure) characteristic and an equivalent circuit, which are the transmission line structure that has the defect made in the ground surface. We used a distribute device and a lumped device, obtained the equivalent circuit by applying the structure of balun to a discontinuous part. An indicated DGS (Defected Ground structure) is a dumbbells-shaped single defect, we indicated satisfying a magnitude and phase characteristics by applying this equivalent circuit.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.2
• /
• pp.195-201
• /
• 1994

The potential ability of the Applebaum type adaptive array to suppress the multipath signals is examined. The output Signal-to-Noise Ratio is expressed in terms of (1) the input SNR. (2) relative multipath signal amplitude, and (3) ambient noise when a multipath component is present Computer simulation is done on several performance measures to learn that the performance of the array depends upon the magnitude and the phase of the correlation coefficient. It is also shown that the performance is maximized when the phase of the correlation coefficient is zero degree.