휴대용 단말에 간편하게 구현 가능하도록 GPS의 코드의사거리 관측치 기반의 정밀단독측위(PPP; Precise Point Positioning) 알고리즘을 개발하고 그 성능을 검증하였다. PPP에 필요한 기본 모델로 그룹 딜레이, 상대성 효과, 위성안테나 위상중심오프셋 보정모델을 적용하였다. 위성 궤도와 시계오차는 IGS(International GNSS Service) 공식 산출물에 최적의 알고리즘을 통해 보간하고, 대류권과 전리층 오차는 각각 과학기술용 GPS 자료처리 소프트웨어로 산출한 참값과 GIM(Global Ionosphere Model)을 사상함수를 적용해 시선방향 오차로 변환해 적용하였다. 개발된 알고리즘을 4일간 테스트한 결과 수평오차는 0.8~1.6m, 수직오차는 1.6~2.2m 수준으로 나타났다. 이는 DGPS 측위결과와 유사한 성능으로 향후 PPP 알고리즘의 추가개선이 이루어질 경우 다양한 측량 및 위치기반서비스 분야에 활용 가능할 것으로 기대된다.
본 논문에서는 마이크로스트립 헤어핀 형태의 링 공진기를 이용하여 저위상 잡음을 개선한 소형화된 S 대역에 사용가능한 발진기를 설계 및 제작하였다. 기판은 고조파 특성이 우수한 유전율 ${\varepsilon}_r$=3.5 기판두께 h=20mil 금속두께 t=17um 손실 탄젠트 $tan{\delta}$=0.0025 인 TACONIC사의 RF-35를 사용하였다. 측정된 결과 발진 주파수는 2.45 GHz에서 출력전력은 20.9 dBm으로서 기존의 발진기에 비하여 상당히 높은 출력을 얻었고, 위상 잡음 특성은 100 kHz offset에서 -100.5 dBc/Hz 로서 기존의 발진기 성능과 비교하면 우수한 특성이 있음을 확인할 수 있었고, 고조파 억압 특성은 32 dBc 이상으로서 우수한 특성을 갖는 발진기임을 보여주었다. 본 논문에서 제안된 발진기의 형태를 이용하여 RFIC, MIC, MMIC 형태로 제작한다면 발진기를 소형화할 수 있을 것이며, 이 제작된 발진기는 S-밴드의 주파수원으로 이용 가능할 수 있을 것으로 사료된다.
KSII Transactions on Internet and Information Systems (TIIS)
/
제6권2호
/
pp.702-721
/
2012
In the DVB-T2 system with a multiple-input single-output (MISO) transmission mode, Alamouti coded orthogonal frequency division multiplexing (OFDM) signals are transmitted simultaneously from two spatially separated transmitters in a single frequency network (SFN). In such systems, each transmit-receive link may have a distinct carrier frequency offset (CFO) due to the Doppler shift and/or frequency mismatch between the local oscillators. Thus, the received signal experiences dual CFOs. This not only causes dual phase errors in desired data but also introduces inter-carrier interference (ICI), which cannot be removed completely by simply performing a CFO compensation. To overcome this problem, this paper proposes an iterative detection with dual phase errors compensation technique. In addition, we propose a successive-iterative ICI cancellation technique. This technique successively eliminates ICI in the initial iteration by exploiting pre-detected data pairs. Then, in subsequent iterations, it performs a fine interference cancellation using a priori information, iteratively fed back from the channel decoder. In contrast to previous works, the proposed techniques do not require estimates of dual CFOs. Their performances are evaluated via a full DVB-T2 simulator. Simulation results show that the DVB-T2 receiver equipped with the proposed dual phase errors compensation and the successive-iterative ICI cancellation techniques achieves almost the same performance as ideal dual CFOs-free systems, even for large dual CFOs.
본 논문에서는 VCDRO, GaAs MESFET, 반사기 등을 이용하여 주파수 체배기 형테로 구성한 K-대역 국부발진기를 설계하고 제작하여 특성을 실험하였다. VCDRO은 위상잡음특성을 개선하기 위하여 저잡음 특성을 가지며 플리커 잡음이 적은 MESFET를 선택하였으며 Q값이 큰 유전체 공진기를 사용하여 선택도를 높였다. 특히, 제안된 주파수 체배기는 반사기와 대역저지필터를 사용함으로써, 일반적인 체배기에 비해 회로의 크기를 줄이고, 고조파 억압특성을 개선했을 뿐만 아니라 더 좋은 변환이득을 얻었다. 제작된 VCDRO의 특성을 측정한 결과, 중심 주파수 12.05 Uh에서 5.8 dRm의 출력 전력과 -37.98 dBc의 고조파 억압, 100 Khz offest 주파수에서 -114 dBc의 위상잡음 특성을 얻을 수 있었으며, 주파수 체배기의 특성을 측정한 결과, 5.8 dBm의 입력신호에 대해 출력 주파수인 24.10 GHz에서 출력 전력은 1.755 dBm이고, 변환이득은 1.482 dB, 고조파 억압은 -33.09 dBc, 100 kHz offset 주파수에서 -98.23dBc의 위상잡음 특성을 얻었다. 주파수 체배 기법을 이용하여 제작된 발진기는 K-대역에서 국부발진기로 이용될 수 있음을 확인하였다.
본 논문에서는 FMCW(frequency modulation continuos wave) 응용에서 사용 가능한 우수한 성능의 W-band 도파관 전압조정발진기를 구현하였다. 중심주파수가 94 GHz인 도파관 전압조정발진기(VCO, voltage controlled oscillator)를 구현하기 위하여 GaAs 건 다이오드(Gunn diode) 및 버렉터 다이오드(varactor diode)와 저역통과필터(LPF, low pass filter)를 적용한 두 개의 바이어스 포스트(bias post)를 이용하였으며, 발진기의 동공(cavity)을 47 GHz에서 발진하도록 설계하여 2체배된 신호를 사용하였다. 제작된 전압조정발진기는 1.095 GHz의 대역폭, 1.69%의 오차율 특성을 갖는 590 MHz의 선형성 구간과 14.86~15.93 dBm의 출력전력 특성을 나타내었다. 위상잡음은 전 구간에서 -95 dBc/Hz(at 1 MHz offset) 이하의 우수한 특성을 얻었다.
This paper provides an efficient model predictive control for the output voltage control of three-phase inverter system which includes output LC filters. Use of SVPWM (Space Vector Pulse-Width-Modulation) and the rotating d-q frame is made to obtain an input constrained dynamic model of the inverter system. From the measured/estimated output current and reference output voltage, corresponding equilibrium values of the inductor current and the control input are computed. Derivation of a feasible and invariant set around the equilibrium state is made and then a receding horizon strategy which steers the current state deep into the invariant set is proposed. In order to remove offset error, use of disturbance observer is made in the form of state estimator. The efficacy of the proposed method is verified through simulations.
This paper presents the control algorithm of a single-phase AC/DC/AC PWM converter for the linear compressor of a refrigerator. The AC/DC/AC converter consists of a full-bridge PWM converter for the control of the input power factor and a half-bridge PWM inverter for the control of the single-phase linear compressor. At the DC-link of this topology, two capacitors are connected in series. These DC-link voltages must be balanced for safe operation. Thus, a new control method of DC voltage balancing for the half-bridge PWM inverter is proposed. The balancing algorithm uses the Integral-Proportional controller and inserts the DC-offset current at the Proportional-Resonant current controller of the inverter to solve the DC-link unbalanced voltages between the two capacitors. The proposed algorithm can be easily implemented without much computation and additional hardware circuit. The usefulness of the proposed algorithm is verified through several experiments.
본 논문에서는 유전체 공진기와 마이크로스트립 라인 간의 결합 구조를 개선시켜 저위상 잡음을 갖는 전압제어 유전체 공진기 발진기(Vt-DRO: Voltage-tuned Dielectric Resonator Oscillator)를 설계, 제작하였다. 설계된 발진기는 유전체 공진기, 위상천이기, 증폭기로 구성된다. 발진기의 위상 잡음은 공진기의 군지연과 밀접하게 관계되며, 이러한 관계를 수식적으로 도출하고, 이를 예측하는 방법을 제안하였다. 유전체 공진기와 마이크로스트립 라인간의 결합 구조를 조정하여 약 53 nsec의 높은 군지연을 갖도록 설계하였다. 각 부의 측정은 측정의 편의성을 위해 웨이퍼 프로브를 이용하였으며, 이를 위하여 각 부의 입출력 포트를 CPW(Coplanar Waveguide)로 설계하였다. 각 부를 연결하여 측정한 S-파라미터는 개루프 발진 조건을 만족하였다. 설계된 개루프의 입출력을 연결하고 폐루프로 구성하여 전압 제어 유전체 공진기 발진기를 구현하였다. 측정 결과, 5.3 GHz의 발진 주파수에서 위상 잡음은 수식으로부터 도출한 값과 근사한, 100 kHz offset 주파수에서 -132.7 dBc/Hz를 얻었다. 이때 출력 전력은 약 4.5 dBm, 전기적 주파수 조정 범위는 0~10 V의 조정 전압에서 약 5 MHz를 보였다. PFTN-FOM(Power Frequency Tuning Normalized Figure of Merit)은 약 -31 dB를 보였다.
본 논문에서는 모바일 RFID 시스템 환경을 제시하였고, 그 환경에 적합한 저 잡음 차동 콜피츠 전압 제어 발진기를 구현하였다. 밀집 리더 환경에 맞춘 전압 제어 발진기는 $0.35{\mu}m$ 공정을 사용하였고, 주파수 범위는 RFID 주파수 범위인 $860{\sim}960 MHz$를 포함시킬 수 있도록 $1.55{sim}2.053 GHz$로 설계하였다. 2분주기 출력에서 측정한 위상 잡음은 오프셋 주파수가 40 kHz일 때 -106 dBc/Hz로 측정되었고, 1MHz일 때에는 -135 dBc/Hz로 측정되었다. 5 비트의 디지털 튜닝을 이용하여 낮은 발진기 이득(<45 MHz/V)을 갖게 하여 주파수 합성기에서의 위상 잡음 특성을 좋게 하였다. 설계한 차동 콜피츠 발진기의 FOM은 1.93 dB로 타 2 GHz 대역의 발진기들 보다 높게 측정되었다.
Handling precise timing in high-speed transceivers has always been a primary design target to achieve better performance. Many different approaches have been tried, and one of those is utilizing the beneficial nature of injection locking. Though the phenomenon was not intended for building integrated circuits at first, its coupling effect between neighboring oscillators has been utilized deliberately. Consequently, the dynamics of the injection-locked oscillator (ILO) have been explored, starting from R. Adler. As many aspects of the ILO were revealed, further studies followed to utilize the technique in practice, suggesting alternatives to the conventional frequency syntheses, which tend to be complicated and expensive. In this review, the historical analysis techniques from R. Adler are studied for better comprehension with proper notation of the variables, resulting in numerical results. In addition, how the timing jitter or phase noise in the ILO is attenuated from noise sources is presented in contrast to the clock generators based on the phase-locked loop (PLL). Although the ILO is very promising with higher cost effectiveness and better noise immunity than other schemes, unless correctly controlled or tuned, the promises above might not be realized. In order to present the favorable conditions, several strategies have been explored in diverse applications like frequency multiplication, data recovery, frequency division, clock distribution, etc. This paper reviews those research results for clock multiplication and data recovery in detail with their advantages and disadvantages they are referring to. Through this review, the readers will hopefully grasp the overall insight of the ILO, as well as its practical issues, in order to incorporate it on silicon successfully.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.