• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.204-211
• /
• 2020

The high-velocity oxy-fuel (HVOF) thermal spraying coating technique has been considered a promising replacement for traditional electrolytic hard chrome plating (EHC), which caused environmental pollution and lung cancer due to toxic Cr⁶⁺. In this paper, two types of cermet coatings were prepared by HVOF spraying: WC-CoCr and WC-CrC-Ni coatings. The produced coatings were analyzed extensively in terms of the micro-hardness, porosity, crystalline phase and microstructure using a hardness tester, optical microscopy, X-ray diffraction, and scanning electron microscopy (including energy dispersed spectroscopy (EDS)), respectively. The wear and friction behaviors of the coatings were evaluated comparatively by reciprocating sliding wear tests at 25 ℃, 250 ℃, and 450 ℃. The results revealed correlations among the microstructures, metallic binder matrixes, porosities, and wear performance of the coatings. For example, WC-CoCr coatings showed better sliding wear resistance than WC-CrC-Ni coatings, regardless of the test temperature due to the more homogeneous microstructure, Co-rich, Cr-rich metallic binder matrix, and lower porosity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.6
• /
• pp.237-241
• /
• 2008

Hot-press sintering of AlN ceramics were carried out with $Y_2O_3$ as sintering additive at a sintering temperature $1,750{\sim}1,850^{\circ}C$. The effect of $Y_2O_3$ addition and sintering time on sintering behavior and thermal conductivity of AlN ceramics was investigated. $Y_2O_3$ added AlN showed noticeably higher denazification rate than pure AlN. The thermal conductivity of AlN specimens was promoted by the addition of $Y_2O_3$ in spite of the formation of YAG secondary phase in AlN grain boundaries and grain boundary triple junction because $Y_2O_3$ addition could reduced the oxygen contents in AlN lattice which is primary factor of thermal conductivity. Typically, the thermal conductivity of 5 wt% $Y_2O_3$ added specimen was dramatically improved by the increase of sintering time because the elimination of YAG secondary phases from the grain boundary due to the evaporation, as well as the grain-growth of AlN grains.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.308-314
• /
• 2016

Cobalt-, zinc-, and nickel-zinc-substituted nano-size manganese ferrite powders, $MnFe_2O_4$, $Mn_{0.8}Co_{0.2}Fe_2O_4$, $Mn_{0.8}Zn_{0.2}Fe_2O_4$ and $Mn_{0.8}Ni_{0.1}Zn_{0.1}Fe_2O_4$, were fabricated using a sol-gel method, and their crystallographic and magnetic properties were subsequently studied. The $MnFe_2O_4$ ferrite powder annealed at temperatures above 523 K exhibited a spinel structure, and the particle size increased as the annealing temperature increased. All ferrites annealed at 773 K showed a single spinel structure, and the lattice constants and particle size decreased with the substitution of Co, Zn, and Ni-Zn. The $M{\ddot{o}}ssbauer$ spectrum of the $MnFe_2O_4$ ferrite powder annealed at 523 K only showed a doublet due to its superparamagnetic phase, and the $M{\ddot{o}}ssbauer$ spectra of the $MnFe_2O_4$, $Mn_{0.8}Co_{0.2}Fe_2O_4$, and $Mn_{0.8}Zn_{0.2}Fe_2O_4$ ferrite powders annealed at 773 K could be fitted as the superposition of two Zeeman sextets due to the tetrahedral and octahedral sites of the $Fe^{3+}$ ions. However, the $M{\ddot{o}}ssbauer$ spectrum of the $Mn_{0.8}Ni_{0.1}Zn_{0.1}Fe_2O_4$ ferrite powder annealed at 773 K consisted of two Zeeman sextets and one quadrupole doublet due to its ferrimagnetic and paramagnetic behavior. The area ratio of the $M{\ddot{o}}ssbauer$ spectra could be used to determine the cation distribution equation, and we also explained the variation in the $M{\ddot{o}}ssbauer$ parameters by using this cation distribution equation, the superexchange interaction and the particle size. Relative to pure $MnFe_2O_4$, the saturation magnetizations and coercivities were larger in $Mn_{0.8}Co_{0.2}Fe_2O_4$ and smaller in $Mn_{0.8}Zn_{0.2}Fe_2O_4$, and $Mn_{0.8}Ni_{0.1}Zn_{0.1}Fe_2O_4$. These variations could be explained using the site distribution equations, particle sizes and magnetic moments of the substituted ions.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.175-182
• /
• 2015

Objective : The purpose of this study was to investigate difference in fascicle behavior of the medial gastrocnemius during the locomotion with varying intensities, such as gait and one-legged and two-legged vertical jumping. Methods : Six subjects (3 males and 3 females; age: $27.2{\pm}1.6yrs.$, body mass: $62.8{\pm}9.8kg$, height: $169.6{\pm}8.5cm$) performed normal gait (G) at preferred speed and maximum vertical jumping with one (OJ) and two (TJ) legs. While subjects were performing the given tasks, the hip, knee and ankle joint motion and ground reaction force was monitored using a 8-infrared camera motion analysis system with two forceplates. Simultaneously, electromyography of the triceps surae muscles, and the fascicle length of the medial gastrocnemius were recorded using a real-time ultrasound imaging machine. Results : Comparing to gait, the kinematic and kinetic parameters of TJ and OJ were found to be significantly different. Along with those parameters, change in the medial gastrocnemius (MG) muscle-tendon complex (MTC) length ($50.57{\pm}6.20mm$ for TJ and $44.14{\pm}5.39mm$ for OJ) and changes in the fascicle length of the MG ($18.97{\pm}3.58mm$ for TJ and $20.31{\pm}4.59mm$ for OJ) were observed. Although the total excursion of the MTC and the MG fascicle length during the two types of jump were not significantly different, however the pattern of length changes were found to be different. For TJ, the fascicle length maintained isometric longer during the propulsive phase than OJ. Conclusion : One-legged and two-legged vertical jumping use different muscle-tendon interaction strategies.

• Archives of design research
• /
• v.13 no.3
• /
• pp.281-292
• /
• 2000

Today, the rapid economic growth and emerging new trends have been changed radically throughout the society and they especially have affected the changes of life-style and the diversity of residents'demands in housing life. This changes of life have brought the shift in family form from traditional type, thus new phase of nuclear family means that it makes on the whole, variable family forms such as single family, non-blood one, a generation one and so on. It therefore is time that we should not only explore current housing plans, but envisage concept of new living space to satisfy latent need of the occupants. But the forms, in spite of the diversity of user's needs and the change of life-style, of many houses as many apartment and tenement houses supplied so far have been clearly limted, and housing policy of the mass-supply causes monotonous space composition, over-occupation and non-changeability. Now, the collective houses have some limits owing to the commoness and assemblage, but they have failed to keep up with the variable and changeable life-style of residents. These problems, to put it concretely, lead to increasing needs for the number of rooms in proportion to family members, for the change of behavior using the space. We therefore need to propose the new living space. As the current plans for designing house are based on the average life-style of people, they can not cope with variable demands of the resident. For that reason, this paper will propose the manual space system as an alternative for it and the goal is to suggest new furniture system which we need to create the flexibility of living space.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1090-1096
• /
• 2002

Six different composition of water-swellable bentonite rheology modifiers(WSB-1~WSB-6) were prepared by the compounding of peptizers and anionic surfactants as an additives with Bentonite(BEN) of montmorillonite group. Average particle size, particle morphology and water-swellability of WSB and the viscosity with additives were measured, respectively. And the rheological behavior of WSB were investigated using the rheometer. The viscosity of WSB-1 increased with decreasing both pH and average particle size of BEN, WSB-2 treated $Na_2CO_3$ as a peptizer showed the maximum viscosity. These results can be interpretated cause for rearrangment as the edge-to-face structure of BEN particles containing WSB. Also, WSB-4∼WSB-6 containing both peptizer and anionic surfactant was sol phase that their viscosity was not nearly with the shear rate, however, WSB-3 containing Tetrasodium Pyrophosphate(TSPP) as an anionic surfactant showed the thixotropy by the viscosity difference of 1000 times with the shear rate. From this result, the anions of TSPP can be explained to arrange in edge of BEN particles containing WSB-3.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.599-604
• /
• 2004

The LTCCs (Low-Temperature Co-fired Ceramics) are very important for electronic industry to build smaller RF modules and to fulfill the necessity for miniaturization of devices in wireless communication industry. The dielectric materials with sintering temperature $T_{sint}$＜90$0^{\circ}C$ are required. In this study, BaO-N $d_2$ $O_3$-Ti $O_2$ (BNT ： 20∼40 wt％) for ceramic materials and L $a_2$ $O_3$- $B_2$ $O_3$-Ti $O_2$ (LBT ： 80∼60 wt％) for crystallizable glasses were used. The glass/ceramic composites were investigated for sintering behavior, phase evaluation, densities, interface reaction and microwave dielectric properties. It was found that the addition LBT glass frist significantly lowered the sintering temperature to below 90$0^{\circ}C$ and the densification with increasing addition LBT glass frist developed rapidly which was meant to be namely 90％ of relative density. The sintered bodies ekhibited applicable dielectric properties, namely 15 for $\varepsilon$$_{r}$,, 10000 GHz for Q＊ $f_{0}$. The results suggest that the composites have good potential as a new candidate for LTCC materials.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.6
• /
• pp.751-763
• /
• 2005

Statement of problem. To improve a direct implant fixation to the bone, various strategies have been developed focusing on the surface of materials. The surface quality of the implant depends on the chemical, physical, mechanical and topographical properties of the surface. The different properties will interact with each other and a change in thickness of the oxide layer may also result in a change in surface energy, the surface topography and surface, chemical composition. However, there is limited the comprehensive study with regard to changed surface and biologic behavior of osteoblast by anodization. Purpose of study. The aim of this study was to analyze the characteristics of an oxide layer formed and to evaluate the cellular biologic behaviors on titanium by anodic oxidation (anodization) by cellular proliferation, differentiation, ECM formation and gene expression. And the phospholipase activity was measured on the anodized surface as preliminary study to understand how surface properties of Ti implant are transduced into downstream cellular events. Methods and Materials. The surface of a commercially pure titanium(Grade 2) was modified by anodic oxidation. The group 1 samples had a machined surface and other three experimental specimens were anodized under a constant voltage of 270 V(Group 2), 350 V(Group 3), and 450 V(Group 4). The specimen characteristics were inspected using the following five categories; the surface morphology, the surface roughness, the thickness of oxide layer, the crystallinity, and the chemical composition of the oxide layer. Cell numbers were taken as a marker for cell proliferation. While the expression of alkaline phosphatase and Runx2 (Cbfa1) was used as early differentiation marker for osteoblast. The type I collagen production was determined, which constitutes the main structural protein of the extracellular matrix. Phospholipase $A_2$ and D activity were detected. Results. (1) The anodized titanium had a porous oxide layer, and there was increase in both the size and number of pores with increasing anodizing voltage. (2) With increasing voltage, the surface roughness and thickness of the oxide film increased significantly (p<0.01), the $TiO_2$phase changed from anatase to rutile. During the anodic oxidization, Ca and P ions were more incorporated into the oxide layer. (3) The in vitro cell responses of the specimen were also dependant on the oxidation conditions. With increasing voltage, the ALP activity, type I collagen production, and Cbfa 1 gene expression increased significantly (p<0.01), while the cell proliferation decreased. (4) In preliminary study on the relation of surface property and phospholipase, PLD activity was increased but $PLA_2$ activity did not changed according to applied voltage. Conclusion. The anodized titanium shows improved surface characteristics than the machined titanium. The surface properties acquired by anodization appear to give rise more mature osteoblast characteristics and might result in increased bone growth, and contribute to the achievement of a tight fixation. The precise mechanism of surface property signaling is not known, may be related to phospholipase D.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.14 no.6
• /
• pp.119-130
• /
• 2019

Although a well-established line of research has addressed the funding decision, the activities of investee startups to receive funding have been overlooked because prior research has been conduced from investor's point of view. In addition, funding does not result from one off decisions but from decision process with many stages. Moreover, the emphasis placed on specific investment criteria varies by different stages during the process. Therefore, understanding the initial funding of startups requires to analyze the strategic behaviors of startups throughout the entire funding decision process from first meeting with investors to funding success. This study investigates the initial funding process of startups, and the analysis is based on a case study of LetinAR one of the successful startups founded by students in South Korea. This study investigates how early start-ups were able to receive funding from startup's point of view, and the analysis is based on a case study of LetinAR, an augmented reality(AR) startup using Pin mirror technology. By adding "legitimacy building" stage that had not been addressed previously, we divided funding process into four stages: 1) legitimacy building, 2) familiarization, 3) screening, and 4) bargaining phase. We did not only analyze major criteria, but also strategic activities of startup at each stage. This study makes a contribution by helping us understand complicated process of funding and the successful strategic behavior of investor backed startups.

• Korean Journal of Environmental Agriculture
• /
• v.20 no.4
• /
• pp.269-276
• /
• 2001

Several experiments including persistence, distribution, leaching, and terminal residue trials were carried out to investigate the behavior of cyclosulfamuron in rice paddies. Cyclosulfamuron was gradually dissipated in two different soils showing the first-order kinetics. Half-lives of the herbicide were calculated to be $17{\sim}30$ and $14{\sim}16$ days under field and laboratory conditions, respectively. In the paddy soil/water system, the residue tended to reside more in the soil phase as time elapsed. Cyclosulfamuron was less persistent in paddy water than in soil with half-lives of 10 and 19 days, respectively. No cyclosulfamuron was leached below 20 cm-deep soil during water percolation with 50 cm hydraulic head, while some downward mobility was observed within the soil column. When EC and SC formulations of cyclosulfamuron were applied to the paddy field at 120 or 150-day pre-harvest intervals, its terminal residues in hulled rice were all less than 0.01 mg/kg, irrespective of formulation type and application timing. In rice straw, however, some residues were found at $<0.02{\sim}0.05$ mg/kg as SC formulation was applied. Rapid dissipation, restricted mobility, and low terminal residues of cyclosulfamuron in rice paddies suggest that no significant residues would be transported or carried over to the non-target environment.