• Ocean Systems Engineering
• /
• v.14 no.1
• /
• pp.17-52
• /
• 2024

In this paper, the authors explore the modeling and control of a point absorber wave energy converter, which is connected to the electric grid via a power converter that is based on a linear permanent magnet synchronous generator (LPMSG). The device utilizes a buoyant mechanism to convert the energy of ocean waves into electrical power, and the LPMSG-based power converter is utilized to change the variable frequency and voltage output from the wave energy converter to a fixed frequency and voltage suitable for the electric grid. The article concentrates on the creation of a predictive control system that regulates the speed, voltage, and current of the LPMSG, and the modeling of the system to simulate its behavior and optimize its design. The predictive model control is created to guarantee maximum energy output and stable grid connection, using Matlab Simulink to validate the proposed strategy, including control side generator and predictive current grid-side converter loops.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.23-30
• /
• 2014

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.106.1-106.1
• /
• 2013

When strong static magnetic field is applied to the TMP, it is expected that the presence of the magnetic field might retard the velocity of the blades which results in the change of the pumping speed of the TMP. However, such effect of the magnetic field on the TMP has not been well characterized. Thus, under the strong magnetic field, monitoring pumping speed as well as generated heat, pressure, and vibration of the TMP may be an important issue to understand the magnetic field tolerance of the TMP and the development of magnetic shielding technique for the key components of the pump. For this purpose, magnetic field generation system to the vertical direction by a circular current source was firstly designed and suggested [K. Baik et al., 44th Annual Conf. KVS, 22(1), 153, (2012)]. In the current study, another magnetic field generation systems are presented to apply the magnetic field to the horizontal and radial directions by the rectangular current sources and the permanent magnets respectively. Such systems were made to generate at least 50 Gauss of magnetic field along the vertical direction and at least 25 Gauss of magnetic field along the horizontal or radial direction. Current study introduces the evaluation system of the magnetic field along the vertical, horizontal, and radial directions and presents the measured experimental results of the magnetic field when such systems are combined with the equipment where TMP will be installed.

• Archives of Craniofacial Surgery
• /
• v.14 no.2
• /
• pp.133-136
• /
• 2013

Retrobulbar hemorrhage is a rare but serious complication after blepharoplasty, mid-face injury, and treatment of facial bone fractures. The incidence of postoperative retrobulbar hemorrhage is 0.055% with an incidence of associated permanent blindness of 0.005%. A 69-year-old male came to the emergency room with pain on both orbital areas and uncontrolled bleeding after cosmetic lower blepharoplasty performed at a private clinic. He had not been evaluated preoperatively by the private clinic, but we found that he had undergone percutaneous transluminal coronary angioplasty and taken anticoagulants for 10 years. We performed an emergency operation to evacuate the hematoma. However, after surgery, he persistently complained of orbital pain, pressure and diminished visual acuity. Intraocular pressure was increased, and computed tomography demonstrated a retrobulbar hemorrhage with globe displacement. Emergent lateral canthotomy and cantholysis were performed. Intraocular pressure was decreased to 48/30 mm Hg immediately after the operation, falling within the normal range the next day. We recommend three points to minimize loss of vision by retrobulbar hematoma. Firstly, careful preoperative evaluation must be conducted including current medications, underlying diseases and previous history of surgeries. Secondly, cautious postoperative observation is important for the early diagnosis of retrobulbar hematoma. Lastly, immediate treatment is crucial to prevent permanent blindness.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.10
• /
• pp.361-372
• /
• 2016

Identity Privacy issues such as exposures of IMSIs(International Mobile Subscriber Identities) in access network have been consistently raised throughout GSM, UMTS, LTE in 3GPP. The 3GPP specification uses temporary identities instead of IMSI to ensure anonymity of the user. Even if temporary identities are disclosed, Identity Privacy may be maintained at a safe level by security policies such as no linkability and periodic update. But in case of IMSI, it cannot be changed even though it is exposed. There still exist some situations that IMSI is used in clear text for the authentication. Therefore, a protective mechanism for the identity confidentiality is needed. In this paper we propose a protocol based on IBE(Identity-based Encryption) to protect permanent identities in access network. By simplifying the scheme, this protocol has minimized the system impact on current 3GPP environment. And this scheme can be applied to all kind of permanent identities and 3GPP AKA(Authentication and Key Agreement) protocols in access network.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.8
• /
• pp.67-73
• /
• 2009

The magnetic saliency effect in surface-mounted permanent-magnet (SMPM) motors on the torque control at high speeds is first presented and analyzed in this paper. The d- and q- axes impedance are measured by proposed State-Filter. Measurement of the d- and q- axes impedance difference is performed to prove the existence of the magnetic saliency. Then, the saliency effects on the torque control performance in the flux weakening region are discussed. Based on the developed motor modeling with the reluctance torque, the proposed control adjusts the d- and q-axis current toward the operating point to track the commanded torque. The feasibility of the presented idea is verified by experimental results on a commercial 600[W] SMPM motor.

• Steel and Composite Structures
• /
• v.6 no.2
• /
• pp.159-182
• /
• 2006

Current fire design codes for determining the temperature within the structural elements that form part of a complete building are based on isolated member tests subjected to the standard fire. However, the standard time-temperature response bears little relation to real fires and doesn't include the effects of differing ventilation conditions or the influence of the thermal properties of compartment linings. The degree to which temperature uniformity is present in real compartments is not addressed and direct flame impingement may also have an influence, which is not considered. It is clear that the complex thermal environmental that occurs within a real building subject to a natural fire can only be addressed using realistic full-scale tests. To study global structural and thermal behaviour, a research project was conducted on the eight storey steel frame building at the Building Research Establishment's Cardington laboratory. The fire compartment was 11 m long by 7 m wide. A fire load of $40kg/m^2$ was applied together with 100% of the permanent actions and variable permanent actions and 56% of live actions. This paper summarises the experimental programme and presents the time-temperature development in the fire compartment and in the main supporting structural elements. Comparisons are also made between the test results and the temperatures predicted by the structural fire Eurocodes.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.855-864
• /
• 2011

In this paper, a nonlinear controller based on adaptive back-stepping method is proposed for high performance operation of IPMSM(Interior Permanent Magnet Synchronous Motor). First, in order to improve the performance of speed tracking a nonlinear back-stepping controller is designed. Since it is difficult to control the high performance driving without considering parameter variation, a parameter estimator is included to adapt to the variation of load torque in real time. In addition, for the efficiency of power consumption of the motor, controller is designed to operate motor with minimum current for maximum torque. The proposed controller is applied through simulation to the a 2-hp IPMSM for the angular velocity reference tracking performance and load torque volatility estimation, and to test the MTPA(Maximum Torque per Ampere) operation in constant torque operation region. The result verifies the efficacy of the proposed controller.

• Journal of Labour Economics
• /
• v.25 no.2
• /
• pp.1-32
• /
• 2002

This paper investigates how real wages adjust to regional and cyclical shocks in the Korean labor market. Major findings are as follows. First, like most longitudinal studies in this literature, we find that real wages are strongly procyclical and more procyclical for men than for women. Second, consistent with the theory prediction of efficiency wages, both permanent and transitory components of real wages are negatively correlated with the local unemployment rate. Third, when overall and local unemployment rates compete in a wage equation (our preferred specification), current wages are dominantly affected by the overall rate, and the effect of the local rate is rather small. This rejects the Blanchflower and Oswald's hypothesis that wages are primarily determined by local labor market conditions. Finally, no lagged effects on wages are detected in the overall or local unemployment rate.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.12
• /
• pp.1828-1835
• /
• 2012

In this paper, a conceptual design and a detailed design of novel cylindrical magnetic levitation stage is introduced. This is came from planar-typed magnetic levitation stage. The proposed stage is composed of cylinder-typed permanent magnet array and semi-cylinder-typed 3 phase winding module. When a proper current is induced at winding module, a magnetic levitation force between the permanent magnet array and winding module is generated. The proposed stage can precisely move the cylinder to rotations and translations as well as levitations with the magnetic levitation force. This advantage is useful to make a nano patterning on the surface of cylindrical specimen by using electron beam lithography under vacuum. Two methods are used to calculate required magnetic levitation forces. The one is 2D FEM analysis, the other is mathematical modeling. This paper shown that results of two methods are similar. An assistant plate is introduced to reduce required currents of winding module for levitations in vacuum. The mathematical model of cylindrical magnetic levitation stage is used for dynamic simulation of magnetic levitations. A lead-lag compensator is used for control of the model. Simulation results shown that the detail designed model of the cylindrical magnetic levitation stage with the assistant plate can be controlled very well.