• Journal of Navigation and Port Research
• /
• v.39 no.6
• /
• pp.457-463
• /
• 2015

A gas turbine engine plays an important role as a prime mover that is used in the marine transportation field as well as the space/aviation and power plant fields. However, it has a complicated structure and there is a time delay element in the combustion process. Therefore, an elaborate mathematical model needs to be developed to control a gas turbine engine. In this study, a modeling technique for a gas generator, a PLA actuator, and a metering valve, which are major components of a gas turbine engine, is explained. In addition, sub-models are obtained at several operating points in a steady state based on the trial running data of a gas turbine engine, and a method for controlling the engine speed is proposed by designing an NPID controller for each sub-model. The proposed NPID controller uses three kinds of gains that are implemented with a nonlinear function. The parameters of the NPID controller are tuned using real-coded genetic algorithms in terms of minimizing the objective function. The validity of the proposed method is examined by applying to a gas turbine engine and by conducting a simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.438-447
• /
• 2004

A new multilevel PWM inverter using a half-bridge and full-bridge cells is proposed for the use of stand-alone photovoltaic inverters. The configuration of the proposed multilevel PWM inverter is based on a prior 11-level shaped PWM inverter. Among three full-bridge cells employed in the prior inverter, one cell is substituted by a half-bridge cell. Owing to this simple alteration, the proposed inverter has three promising merits. First it increases the number of output voltage levels resulted in high quality output voltages. Second, it reduces two power switching devices by means of employing a half-bridge cell. Third, it reduces power imposed on a transformer connected with the half-bridge unit. That is to say, most power is transferred to loads via cascaded transformers connected with low switching inverters, which are used to synthesize the fundamental output voltage levels whereas the output of a transformer linked to a high switching inverter is used to improve the final output voltage waves; thus, it is desirable in the point of the improvement of the system efficiency. By comparing to the prior 11-level PWM inverter, it assesses the performance of the proposed inverter as a stand-alone photovoltaic inverter. The validity of the proposed inverter is verified by computer-aided simulations and experimental results.

• Journal of KIISE
• /
• v.43 no.1
• /
• pp.106-118
• /
• 2016

Recently, as the generation and sharing of web data have increased, the importance of a social semantic web that combines the semantic web and the social web has also been increasing. In this paper, we propose a trust evaluation scheme based on provenance by extending the PROV model in the social semantic web environment. The proposed scheme manages the provenance of web data and adds the necessary elements for trust evaluation in the PROV model of W3C. The extended PROV model supports data management and provenance tracing. The proposed trust evaluation scheme considers various parameters such as user trust, original data trust, and user evaluation. The evaluated trust is managed as provenance. When processing a query, the proposed scheme generates a result by considering the trust. Therefore, the proposed scheme can manage the provenance of web data and compute data trust correctly by using such various parameters. The evaluated trust becomes a criterion to determine whether the query result can be trusted or not. In order to show the validity of the proposed scheme, we verify its performance using SPARQL queries.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.3
• /
• pp.931-942
• /
• 2010

A home network provides users with a variety of information services. The kind and quality of the services can be substantially enhanced by utilizing a variety of data from sensors. However, home networks currently limit their potential by focusing on providing multimedia services rather than services utilizing sensor data. Outdoor electronics are frequently made in a form that emphasizes only certain limited functions in contrast to home appliances. Thus, sensors with one or two functions rather than many can be used in outdoor systems and their use will be more economical than using sensor nodes indoors with more complex home appliances. In this study, we chose to work with motion sensors as they have many potential uses, and we selected a parking lot control system with to use the motion sensors. This parking lot control system was implemented and applied as part of a home network. For this purpose, we defined and implemented a protocol to manage the network in a ubiquitous sensor network environment for the wireless home network in this study. Although a network management system in a Ubiquitous Sensor Network (USN) related to this study is being advanced for other projects, the protocol interface and message system have not yet been clearly defined for use in a general purpose network or in an extension into heterogeneous kinds of networks, communication support, etc. Therefore, USN network management should be conducted for management of faults, composition, power, and applications. To verify the performance of the protocol interface designed in this study, we designed and implemented the necessary units (sensor nodes, sensor gateway, and server) for each network section and, with them, proved the validity of this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1451-1458
• /
• 2013

This paper deals with the programs and algorithms that generate the full data set that satisfy the basic combinatorial requirement of combination, permutation, partial permutation or shortly r-permutation, which are used in the application of the total data testing or the simulation input. We search the programs able to meet the rules which is permutations and combinations, r-permutations, select the fastest program by field. With further study, we developed a new program reducing the time required to processing. Our research performs the following pre-study. Firstly, hundreds of algorithms and programs in the internet are collected and corrected to be executable. Secondly, we measure running time for all completed programs and select a few fast ones. Thirdly, the fast programs are analyzed in depth and its pseudo-code programs are provided. We succeeded in developing two programs that run faster. Firstly, the combination program can save the running time by removing recursive function and the r-permutation program become faster by combining the best combination program and the best permutation program. According to our performance test, the former and later program enhance the running speed by 22% to 34% and 62% to 226% respectively compared with the fastest collected program. The programs suggested in this study could apply to a particular cases easily based on Pseudo-code., Predicts the execution time spent on data processing, determine the validity of the processing, and also generates total data with minimum access programming.

• Tunnel and Underground Space
• /
• v.21 no.5
• /
• pp.394-405
• /
• 2011

In this paper, we applied coupled non-isothermal, multiphase fluid flow and geomechanical numerical modeling using TOUGH-FLAC coupled analysis to study the complex thermodynamic and geomechanical performance of underground lined rock caverns (LRC) for compressed air energy storage (CAES). Mechanical stress in concrete linings as well as pressure and temperature within a storage cavern were examined during initial and long-term operation of the storage cavern for CAES. Our geomechanical analysis showed that effective stresses could decrease due to air penetration pressure, and tangential tensile stress could develop in the linings as a result of the air pressure exerted on the inner surface of the lining, which would result in tensile fracturing. According to the simulation in which the tensile tangential stresses resulted in radial cracks, increment of linings' permeability and air leakage though the linings, tensile fracturing occurred at the top and at the side wall of the cavern, and the permeability could increase to $5.0{\times}10^{-13}m^2$ from initially prescribed $10{\times}10^{-20}m^2$. However, this air leakage was minor (about 0.02% of the daily air injection rate) and did not significantly impact the overall storage pressure that was kept constant thanks to sufficiently air tight surrounding rocks, which supports the validity of the concrete-lined underground caverns for CAES.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.8
• /
• pp.65-75
• /
• 2013

This paper proposes a method of tracking the hand region and detecting the fingertip using only depth images. In order to eliminate the influence of lighting conditions and obtain information quickly and stably, this paper proposes a tracking method that relies only on depth information, as well as a method of using region growing to identify errors that can occur during the tracking process and a method of detecting the fingertip that can be applied for the recognition of various gestures. First, the closest point of approach is identified through the process of transferring the center point in order to locate the tracking point, and the region is grown from that point to detect the hand region and boundary line. Next, the ratio of the invalid boundary, obtained by means of region growing, is used to calculate the validity of the tracking region and thereby judge whether the tracking is normal. If tracking is normal, the contour line is extracted from the detected hand region and the curvature and RANSAC and Convex-Hull are used to detect the fingertip. Lastly, quantitative and qualitative analyses are performed to verify the performance in various situations and prove the efficiency of the proposed algorithm for tracking and detecting the fingertip.

• Journal of the Korea Convergence Society
• /
• v.10 no.1
• /
• pp.163-176
• /
• 2019

The purpose of this study is to examine the impact of PM consultant leadership competence on consulting repurchase intention and the impact of SME CEO participation on consulting repurchase intention. The validity of the measurement model was secured through CFA (Confirmative Factor Analysis) for the questionnaire data, and consistency was secured through the same method convenience, and significant results were obtained. In other words, not only the ability of PM consultant in repurchase of consulting is important, but also confirms that repurchase intention differs according to the participation of manager. Therefore, the performance that manager feels depends on the degree of manager's interest in repurchase and plays an important role in repurchase. As a result, it is important for PM to report to manager and / or make the manager participate in consulting process so that manager can be interested. In this study, it is difficult to generalize the relationship between PM's leadership role and manager's involvement in the repurchase intention. However, it is meaningful that PM's competence as well as management's participation are very important, and that this study figured out which drection PM's leadership should focus on. The purpose of this study is to investigate the effect of the variables on the repurchase intention.

• Journal of vocational education research
• /
• v.37 no.3
• /
• pp.1-23
• /
• 2018

The purpose of this study was to develop evaluation indicators which can help decision making in the quality control and improvement of the job capability strengthening program for the vocational high school depending on the situation, input, process and output of CIPP evaluation model. For this purpose, through the literature review and the research of expert opinions, the evaluation indicators for the job capability strengthening program in the vocational high school was designed. In addition, the Delphi research was conducted to 15 teachers in charge of job searching in specialized high schools and education related experts to validate it. The CVR value which indicates the value of validity was analyzed through the findings of the collected Delphi questionnaires and the degree of opinion consistency was analyzed through the degrees of agreement and convergence. Through the correction and complementation, the final evaluation criteria and evaluation indicators was decided. The evaluation criteria developed from the findings include 7 references such as requirement analysis, objective setting, implementation plan, implementation contents, program activities, program control & evaluation and program performance. Each Criteria has 41 evaluation indicators. It is expected that the finally decided evaluation indicators would be used by the people concerned with the job capability strengthening program at the vocational high schools and contribute to the quality improvement of the job capability strengthening program at the vocational high schools as well as its future directions.

• Korean Journal of Construction Engineering and Management
• /
• v.20 no.1
• /
• pp.114-123
• /
• 2019

Tracking ICT applications on construction business processes is critical to the success of ICT-applied construction projects. Existing IDEF0 is a representative modeling method for visualizing and analyzing business processes. It defines a construction production process into a visual information model, hence, encouraging the project participant to understand the activities, their deliverable, and control flow of the process. However, IDEF0 dose not lend itself to ICT-applied construction processes, because it does not provide a mean to define how, in what order, by which each and every activity that ICT applied implements. This paper presents a new business modeling method that improves the traceability of ICT application (IAMB: ICT Application tracking Model for Business process) for construction management. The IAMB contributes to handle the sophisticated features of construction management processes to which ICT are applied. The method categorizes the process into three types: management, construction, and information exchange. The validity of IAMB was confirmed by analyzing the performance when it is used for tracking each modeling step of lift reservation process which making use of ICT. The test case provides an admissible evidence that the method encourage to define who, what, how, which order, and by which ICT tools the construction process exchanges production information.