• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.1
• /
• pp.78-91
• /
• 2005

Performance limiting factors (PLFs) derived from 161 drinking water treatment plants (DWTPs), assessed by International Technical Diagnosis & Assistance Center, were analyzed and evaluated in more detail in this study. In order to conduct study, 161 DWTPs were divided into five categories depending on their capacity, and into twelve groups according to processes and facilities. From the results of analysis, PLFs and their distribution ratio derived from each category were significantly different. Filtration was the most important performance limiting process in all DWTPs of five categories, and the PLFs in filtration were backwashing velocity, media configuration, bed depth, and formation of mud-ball. The PLFs in coagulation-flocculation process were found out to be coagulant dosage, mixing speed, mechanical problems, and others in the order of frequency of occurrence. Also, insufficient disinfection ability that is resulted from insufficient hydraulic detention time and improper chlorine dose and injection point, is the most significant among PLFs in a clear well. In the case of sedimentation, inappropriate baffle structure and excessive upward velocity were PLFs. In addition, the results showed that high turbid water and low alkalinity in a rainy season, ferric and manganese ions, and ammonia nitrogen have been contributed significantly on the performance of DWTPs.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.577-580
• /
• 1996

LQ-servo is a stability-robustness guaranteed multivariable controller design method based on the LQR structure to improve command following performance with output feedback. In this paper, a new type of PI controller based on LQ-servo is introduced. Then, Command following performance is improved using the limiting behavior of the control gain and weighting factors on the low frequency part of design parameter Q that is the state weighting matrix in the cost function.

• Asian-Australasian Journal of Animal Sciences
• /
• v.32 no.4
• /
• pp.519-526
• /
• 2019

Objective: We determined the risk factors limiting first service conception (FSC) rate in dairy cows and their economic impact. Methods: Data were collected from 790 lactations regarding cow parity, peri- and postpartum disorders, body condition score (BCS), reproductive performance, and expenses associated with reproductive management (treatment, culling, and others). Initially, we identified the risk factors limiting FSC rate in dairy cows. Various biological and environmental factors, such as herd, cow parity, BCS at 1 month postpartum and first artificial insemination (AI), resumption of cyclicity within 1 month of calving, year, AI season, insemination at detected estrus or timed AI, peri- and postpartum disorders, and calving to first AI interval, were evaluated. Next, we evaluated the economic impact of the success or failure of FSC by comparing the expense associated with reproductive management until conception between cows that did or did not conceive at their first service. Results: Cows with BCS <3.0 had a lower probability of conceiving at first insemination (odds ratio [OR] = 0.64, p<0.05) than cows with $BCS{\geq}3.0$. Cows inseminated during summer were less likely to conceive (OR = 0.44, p<0.001) than cows inseminated during spring. Cows with peri- or postpartum disorders were less likely to conceive (OR = 0.55, p<0.001) than cows without disorders. Survival curves generated using MedCalc showed an 81 day extension in the mean interval between calving and conception in cows that failed to conceive over those that did conceive at first insemination. Cows failing conceive required additional expenditure on reproductive treatment ($55.40) and other management ($567.00) than cows that conceived at first insemination. Conclusion: Lower BCS, hot weather at first insemination, and peri- and postpartum disorders are risk factors limiting FSC, which result in an economic loss of $622.40 per dairy cow.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1129-1129
• /
• 2009

Here the improved performance of polymer/polymer solar cells, which are of importance to achieve real plastic solar cells in the near future, is reported. First, the progress in polymer/polymer solar cells is briefly reviewed and then the limiting factors are discussed in terms of charge transport.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.11
• /
• pp.1013-1020
• /
• 2004

The hybrid system of gas turbine and fuel cell is expected to produce electricity more efficiently than conventional methods, especially in small power applications such as distributed generation. The solid oxide fuel cell (SOFC) is currently the most promising fuel cell for the hybrid system. To realize the conceptual advantages resulting from the hybridization of gas turbine and fuel cell, optimized construction of the whole system must be the most important. In this study, parametric design analyses for pressurized GT/SOFC systems have been peformed considering probable practical limiting design factors such as turbine inlet temperature, fuel cell operating temperature, temperature rise in the fuel cell and soon. Analyzed systems include various configurations depending on fuel reforming type and fuel supply method.

• Proceedings of the SAREK Conference
• /
• 2004.06a
• /
• pp.177-177
• /
• 2004

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.8
• /
• pp.1298-1309
• /
• 1999

The nutritional value of protein varies between feedstuffs. It is possible to feed animals using crystalline amino acids as a sole nitrogen source, but in practice only some limiting amino acids are added to the diet. In order to use feedstuffs efficiently, it is important to determine exact amino acid requirements. Reported values differ widely because the requirements are affected by various factors. In this report, therefore, the factors affecting amino acid requirements are reviewed as follows: 1) availability of dietary amino acids, conversion factors of nitrogen to protein, interaction of amino acids, and strain, sex and age of animals; 2) amino acid requirements for maximum performance and maintenance, usefulness of non-essential amino acids; 3) plasma amino acid concentration as a parameter to determine amino acid requirements; and 4) nitrogen excretion to reduce environmental pollution. These factors should be considered, it is to improve the dietary efficiency, which is to reduce excess nitrogen excretion for environmental pollution.

• IE interfaces
• /
• v.13 no.4
• /
• pp.751-758
• /
• 2000

Situation awareness is defined as a person's perception of the elements of the environment within a volume of time and space, the comprehension of their meaning and the projection of their status in the near future. Situation awareness is important in attempting to evaluate human behavior in operating complex systems such as aircraft, air traffic control, and nuclear power plant systems. From the literatures this study reviews the relationship between situation awareness and numerous individual, system and environmental factors, and also reviews the methodologies for the empirical measurement of situation awareness applicable to Korea Next Generation Reactor (KNGR) design project. Attention, working memory, workload, stress, system complexity, and automation are presented as critical factors limiting operator's situation awareness. Mental models and goal-directed behavior are hypothesized as important mechanisms overcoming these limits. This study summarized hypothesized guidelines for interface design to improve situation awareness of reactor operators. Some of the guidelines should be tested in the KNGR evaluation experiments in the future.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.11
• /
• pp.15-21
• /
• 1999

The scalability of optical cross-connect nodes is analyzed based on the limiting factor of transmission performance. The limiting factors considered are ASE noise accumulation and gain saturation in the optical amplifiers, and crosstalk in both wavelength multiplexers/demultiplexers and optical switches. When the wavelength multiplexer/demultiplexers crosstalk is lower than 25dB, Power Penalty is below 1dB for the cascaded transmission of 10 nodes with 4 input/output ports. When 10Gbps signals are transmitted through nodes with 4 and 16 input/output Ports, performance degradation due to switch crosstalk is dominant compared to that due to ASE noise accumulation if the switch crosstalk is larger than 30dB and 45dB, respectively. For the single stage transmission of 10Gbps signal with 21dB fiber link loss, the maximum loss of optical cross-connect nodes must be under 34dB to achieve the BER of $10^{-12}$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.72-72
• /
• 2011

Surface science is intrinsically related to the performance of solar cells. In solar cells the generation and collection of charge carriers determines their efficiency. Effective transport of charge carriers across interfaces and minimization of their recombination at surfaces and interfaces is of utmost importance. Thus, the chemistry at the surfaces and interfaces of these devices must be determined, and related to their performance. In this talk we will discuss the role of two important interfaces, First, the role of surface passivation is very important in limiting the rate of carrier of recombination. Here we will combine x-ray photoelectron spectroscopy of the surface of a Si device with electrical measurements to ascertain what factors determine the quality of a solar cell passivation. In addition, the quality of the heterojunction interface in a ZnSe/CdTe solar cell affects the output voltage of this device. X-ray photoelectron spectroscopy gives some insight into the composition of the interface, while ultraviolet photoemission yields the relative energy of the two materials' valence bands at the junction, which controls the open circuit voltage of the solar cell. The relative energies of ZnSe and CdTe at the interface is directly affected by the material quality of the interface through processing.