• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.202-206
• /
• 2001

In this paper a novel dielectric resonator (DR) bandpass filter (BPF) with flexible arrangement of attenuation poles is proposed. This DR filter is similar to a conventional DR filter except adding a microstrip line below a DR, which not only shifts the location of attenuation poles, but also improves skirt characteristics. The duplexer with the proposed DR BPF has been yielded better isolation and sharper skirt behavior than that with a conventional DR alter. The implemented duplexer has shown a good performance and been well agreed with the simulation.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.319-322
• /
• 1998

In this paper we further propose to add a very simple regenerative clamping circuit to SSIPP to reduce the voltage stress and to recycle the energy trapped in the leakage inductance of the isolation transformer, thus eliminating the need for a lossy snubber circuit. In addition, this proposed clamping circuit also provides a mechanism to reset the magnetizing current of the output transformer of SSIPP employing a Forward converter as the output stage. Simulations and experimental results are reported to verify the operation and performance of the SSIPP with regenerative clamping.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.430-431
• /
• 2011

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.5
• /
• pp.370-374
• /
• 1991

A high performance fully ion-implanted InP JFET was characterized for high speed switching elements. The switch has an insertion loss of 5.5dB with 31.6dB isolation at 1GHz. This device can effectively swithc a byte-multiplexed 2Gb/s signal and an eye-diagram taken at 2Gb/s shows an error-free eye pattern. Therefore, this device can be used as a switching element for high transmission data rate for monolithic integration of optoelectronic circuit in the long-wavelength region.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.129-130
• /
• 2007

I/Q demodulator is designed using RC-CR quadrature divider with two balanced mixer for WLAN applications. The I/Q demodulator has low power dissipation, good I/Q mismatch, a good isolation and conversion loss. The measured results shows close agreement with the predicted performance.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.98-100
• /
• 1987

A granite optical table with a vibration isolator system is designed and constrvcted. The table top is made with granite and the vibration isolation system is constrvcted using a pneumatic isolator. The performance of the table is evalvated by the vibration measurement.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10a
• /
• pp.652-654
• /
• 2004

클라이언트와 서비스 제공자간의 서비스 수준 계약인 SLA(Service Level Agreement)를 만족시키기 위해서는 클라이언트 요청을 우선순위 클래스로 구분하여, 낮은 수준의 서비스를 요청하는 클라이언트보다는 고수준의 서비스를 요구하는 클라이언트에게 우선적으로 서비스를 제공할 수 있는 기술이 필요하다. 본 논문에서는 서비스 제공자의 웹 서버 노드를 우선 순위에 따라 정적.동적으로 분할하는 방법을 연구하였으며, 시뮬레이션을 통해 SLA를 고려할 수 있는 응답시간 성능을 분석하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.134-138
• /
• 2006

The isolation performance of the S-band single-pole single-throw(SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide(GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9 dB is obtained with the coplanar wire-bond interconnection(CWBI) at a 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion(IMD3) are less than 1.94 dB over $3.2{\sim}3.6\;GHz$ and greater than 64 dBc.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4A
• /
• pp.303-309
• /
• 2011

Laminated rubber bearing is the most commonly used device for seismic base isolation of bridge structures. It is important to know performance and behavior characteristics of the laminated rubber bearings. The main evaluation factors of the rubber bearing are classified as compressive, shear and tensile behavior characteristics. The reference data of compressive and shear characteristics are rich, but the reference data of tensile characteristics is scarce. In this study, tensile test results of the rubber bearing with variation of shape factor and shear deformation are investigated for mechanical property. When tensile deformation in normal condition is increasing, tensile cycle behavior curve becomes non-linear and tensile breaking point is 300%. On the other hand, tensile breaking point is shear deformation condition is about 40%. Furthermore, when shape factor is lower, tensile breaking point is decrease. This results mean that tensile breaking point is decreased in triaxial tensile deformation because of cracks caused by internal void of the rubber bearings. This experimental data can be used as the reference data of tensile characteristics for designing seismic isolation of structures.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.366-376
• /
• 2002

A sensor fault detection and isolation scheme(SFDIS) is adopted to improve the reliability of direct torque controlled induction motor drives and the experimental results are discussed. Major contributions include: experimental analysis of a few important sensor faults. design and implementation of the proposed SFDIS, and the fault tolerant control system(FTCS). Although the adopted SFDIS employs only one observer for residual generation, the system has the function of fault isolation that only multiple observer schemes can have. To verify the performance of the proposed scheme, the speed control system is designed for the 2.2kW direct torque controlled Induction motor. Hardware of the control system consists of a control board using TMS320OVC33 and a power stack using IPM. Experimental results for various type of sensor faults show the effectiveness of the SFDIS and the FTCS.