• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.442-455
• /
• 2016

The resistance and seakeeping performance of a high-speed monohull vessel were investigated through a series of model tests in a towing tank. The hull had a slender wave-piercing bow, round bilge, and small deadrise angle on stern. Tests on the bare hull in calm water were first conducted and tests on spray rails followed. The spray rails were designed to control the flow direction and induce a hydrodynamic lift force on the hull bottom to reduce trim angle and increase rise of the hull. The maximum trim of the bare hull was $4.65^{\circ}$ at the designed speed, but the spray rails at optimum location reduced trim by $0.97^{\circ}$. The ship motion in head seas was examined after the calm water tests. Attaching the rails on the optimum location effectively reduced the pitch and heave motion responses. The vertical acceleration at the fore perpendicular reduced by 11.3%. The effective power in full scale was extrapolated from the model test results and it was revealed that the spray rails did not have any negative effects on the resistance performance of the hull, while they effectively stabilized the vessel in calm water and waves.

• Journal of Korean Association for Spatial Structures
• /
• v.19 no.2
• /
• pp.63-72
• /
• 2019

Wireless sensors are more favorable in measuring structural response compared to conventional sensors in terms of them being easier to use with no issues with cables and them being considerably cheaper. Previous tests have been conducted to analyze the performance of MEMS (Micro Electro Mechanical Systems) sensor in sinusoidal excitation tests. This paper analyzes the performance of in-built MEMS sensors in devices by comparing with an ICP sensor as the reference. Earthquake input amplitude excitation in shaking table tests was done. Results show that MEMS sensors are more accurate in measuring higher input amplitude measurements which range from 100gal to 250gal than at lower input amplitudes which range from 10gal to 50gal. This confirms the results obtained in previous sinusoidal tests. It was also seen that natural frequency results have lower error values which range from 0% to 3.92% in comparison to the response spectra results. This also confirms that in-built MEMS sensors in mobile devices are good at estimating natural frequency of structures. In addition, it was also seen that earthquake input amplitudes with more frequency contents (Gyeongju) had considerably higher error values than Pohang excitation tests which has less frequency contents.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.389-392
• /
• 2011

In this study, the engine performance data was extracted and analyzed through the flight test of Smart UAV which is tilt rotor aircraft. The flight test was conducted for the transition flight regime where the tilt angle of prop-rotor varies from 90 degree to 0 degree and vice versa. The engine performance data such as engine power and specific fuel consumption gathered from flight tests were compared well with the results of engine performance analysis program.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.2
• /
• pp.229-234
• /
• 2011

For Lift-type Vertical Axis Wind Turbine (VAWT), it is difficult to evaluate the performance through the scale-model wind tunnel tests, because of the scale effect relating to Reynolds number. However, it is beneficial to figure out the critical value of Reynolds number or minimum size of the Lift-type VAWT, when designing this type of micro wind turbine. Therefore, in this study, the performance of several scale-models of Lift-type VAWT (Reynolds number : $1.5{\times}10^4$ to $4.6{\times}10^4$) was investigated. As a result, the Reynolds number effect depends on the blade chord rather than the inlet velocity. In addition, there was a transition point of the Reynolds number to change the dominant driving force from Drag to Lift.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1117-1122
• /
• 2006

The PEM type regenerative fuel cell(RFC) for the ground simulator of the regeneration electric power system has been designed, manufactured, and tested. In this paper, the designing and manufacturing procedures of the RFC were presented. Also, the performance test results were showed briefly. The RFC consists of PEM type stack, humidifier, pressure and flow control valve, storage tanks, pump and controller. The performance tests were carried out with stack and system performance tests. The performance targets are more than 50% stack efficiency, 1.5kW stack power, less 400W parasitic power in design condition. Most of the performances required are satisfied.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.2
• /
• pp.190-201
• /
• 1985

Direct cutting tests was carried out to evaluate the dynamic performance of lathes under various cutting conditions. Significant factors influencing the chatter limits were identified through use of analysis of variance. Dynamic performances of two lathes were compared and the merits and drawbacks of the direct cutting test were discussed. Exciting-direct-cutting test method was newly proposed as a more rational method of dynamic performance test. The basic theory and experiments of the test were explained. The results shows that the method can be used as a powerful tool for the evaluation and the improvement of dynamic performance of machine tools.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.165-170
• /
• 1992

In this paper, the Hardware-In-The-Loop Simulation(HILS) of missile systems are studied. The HILS is an effective performance evaluation technique that bridges the simulation fidelity gap between analytic all-digital simulations and actual flight tests of missile systems. The HILS may be required to perform system integration tests, performance evaluation at system or subsystem level. Major elements of this HILS facility will include the flight table, simulation computers, I/O computer and peripheral equipments. HILS of missile systems typically involve computer modeling of flight dynamics coupled with a hardware guidance and control(G/C) systems. This paper describes a real time performance evaluation technique of a G/C system, Development of a HILS for a Autopilot of SAM G/C will be used as an example.

• Journal of Aerospace System Engineering
• /
• v.10 no.1
• /
• pp.111-117
• /
• 2016

A new configuration of tiltrotor UAV previously suggested by Korea Aerospace Research Institute (KARI) for the purpose of increasing the endurance performance in airplane mode flight has extended wings attached to the nacelle and rotated with the nacelle according to the flight modes. In this research, the effectiveness of the extended wing on the enhancement of the endurance performance of KARI tiltrotor UAV (TR60) was analytically investigated based on CFD analysis results. Flight tests and ground tests of measuring the fuel consumption were also conducted to directly compare the endurance performance for the two configurations of TR60 baseline and TR60 extended-wing model.

• International Journal of Contents
• /
• v.5 no.4
• /
• pp.75-80
• /
• 2009

Recently high-speed memory array based on RAM, which is a type of solid-state drive (SSD), has been introduced to handle the input/output (I/O) bottleneck. But there are only a few performance studies on RAM based SSD storage with regard to diverse workloads. In this paper, we focus on the file system for RAM based memory array based NGS (Next Generation Storage) system which is running on Linux operating system. Then we perform benchmark tests on practical file systems including Ext3, ReiserFS, XFS. The result shows XFS significantly outperforms other file systems in tests that represent the storage and data requests typically made by enterprise applications in many aspects. The experiment is used to design the dedicated file system for NGS system. The results presented here can help enterprises improve their performance significantly.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.190-191
• /
• 2019

In complex waterproofing method, the stability of the joint is an important factor. The joints should not be broken for repeated movements and tensile forces. Therefore, we tried to confirm the stability of joints in newly developed joints and general joints. Repeated fatigue resistance performance tests and joint tensile strength tests were carried out on four types of joints. The fatigue resistance performance test showed no abnormality in all four types. It was confirmed that the newly developed top-down joint has higher stiffness than existing joints.