• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.273-279
• /
• 2008

The purpose of this study is not only to evaluate thermal performance but also to find the stress behavior of heat transfer tubes under the part load operation in Heat Recovery Steam Generator. Flow analysis was performed to know the behavior of exhaust gas from gas turbine and thermal performance was calculated using distribution of hot exhaust velocity. In addition, tubes temperature during operation were gathered from actual plant to verify the uneven flow distribution under part load operation. Stress analysis was performed using tubes temperature data gathered from actual plant under both part and full load operations to know the stress behavior of tubes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.419-422
• /
• 2006

Improvement of performance of sorbitol model rocket was studied. The rocket designed in this work was compared with the rocket manufactured previously with respect to the shape of body, grain of rocket motor, motor case and recovery system. From this comparative work, it is found that mass ratio is required to be increased and the rocket was designed under safety regulation.

• Proceedings of the KIPE Conference
• /
• 2004.11a
• /
• pp.76-80
• /
• 2004

This paper describes a load simulator with power-recovery capability, which is based on the voltage source converter-inverter set. The load simulator described in this paper can save the electric energy that should be consumed to test the operation and performance of the distributed generation system and the power quality compensator. The load simulator consists of a converter-inverter set with a DSP controller for system control and PWM pulse generation. The converter operates as a universal load to model the linear load and the non-linear load, while the inverter feed the energy back to the power source with harmonic compensation. The load simulator can be widely used in the lab to test the performance of the distributed generation system and the power quality compensator.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.7
• /
• pp.529-536
• /
• 2007

The perforated type element for a heat recovery ventilation system has been studied to improve the performance. Four holes of diameter of 6mm are punched out for each flow channel to break the boundary layer development and increase the turbulence. KS cooling and heating conditions and test procedures are applied for study. The efficiencies are compared to those of the typical element with smooth surface. For cooling operations, the temperature, latent and enthalpy efficiencies increase 2.5%, 18% and 8%, respectively. For heating operations, the temperature, latent and enthalpy efficiencies increase 3%, 5% and 3.2%, respectively.

• Macromolecular Research
• /
• v.16 no.7
• /
• pp.644-650
• /
• 2008

This study examined the effect of nanoclays on the shape memory behavior of polyurethane (PU) in fibrous form. A cation was introduced into the PU molecules to disperse the organo-nanoclay (MMT) into poly($\varepsilon$-caprolactone) (PCL)-based PU (PCL-PU). The MMT/PCL-PU nanocomposites were then spun into fibers through melt-processing. The shape memory performance of the spun fibers was examined using a variety of thermo-mechanical tests including a new method to determine the transition temperature of shape memory polymers. The MMTs showed an improved the fixity strain rate of the MMT /PCL- PU fibers but a slight decrease in their recovery strain rate. This was explained by the limited movement of PU molecules due to the presence of nanoclays. The shape memory performance of the MMT/PCL-PU fibers was not enhanced significantly by the nanoclays. However, their recovery power was improved significantly up to a strain of approximately 50%.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1251-1258
• /
• 2015

We investigate an image recovery method for sparse-view computed tomography (CT) using an iterative shrinkage algorithm based on a second-order approach. The two-step iterative shrinkage-thresholding (TwIST) algorithm including a total variation regularization technique is elucidated to be more robust than other first-order methods; it enables a perfect restoration of an original image even if given only a few projection views of a parallel-beam geometry. We find that the incoherency of a projection system matrix in CT geometry sufficiently satisfies the exact reconstruction principle even when the matrix itself has a large condition number. Image reconstruction from fan-beam CT can be well carried out, but the retrieval performance is very low when compared to a parallel-beam geometry. This is considered to be due to the matrix complexity of the projection geometry. We also evaluate the image retrieval performance of the TwIST algorithm -sing measured projection data.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.55-59
• /
• 2003

In this paper, we estimate the performance requirements of general-purpose DSP for Carrier Recovery of OFDM DVB-T receiver. Firstly, we transported the designed fixed-point OFDM DVB-T model to a floating-point software model written in C. Then, we measured the number of instruction cycles required for operation of Carrier Recovery in time. We use SignalMaster$\^$TM/ DSP platform of LYRtech Inc. as a environment of estimation, and Simulink$\^$TM/ as a graphical interface, Code Composer StudioTM of TI as profiler and compiler, and SPW$\^$TM/ for presenting functional reliability and comparing the performance distortion with fixed-point model. As a result, we show the required number of DSPs in our DSP-based system, and introduce the need of Multi-DSP-based system.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.88-91
• /
• 2000

In this paper we approach the problem of congestion control for TCP traffic over ATM-UBR networks by focusing on the fact that to get best performance. We study how to efficiently support TCP traffic in the subnet ATM model, when ATM is only a single link in the whole path. We show that when UBR connection. We analyze the ATM-UBR network service using the BSD 4.3 Reno, Tahoe TCP. However we found the fact that the characteristic of fast recovery algorithm makes a serious degradation of performance in multiple cell loss drop situation. We propose new fast recovery algorithm to solve the problem.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.3
• /
• pp.1-4
• /
• 2005

As high temperature superconductor applications became a reality due to increase in coated conductor performance, it is important to understand their stability behavior to design safe electrical power systems. Coated conductors can be stabilized with different metals and alloys for different types of application, to yield excellent electrical, thermal and mechanical performance. We have experimentally studied the dependence of quench and recovery characteristics of stainless steel stabilized coated conductors on the amplitude of current and duration time. Stability test of 3cm long sample were performed in a liquid nitrogen bath cooling condition by applying a short period over current pulses for 50 and 100ms, with amplitude up to ~6 times the critical current. The transport current that flows before and after the current pulse was fixed at about ~80-85% critical current. We analyzed the quench and recovery phenomena of the test sample using the current voltage characteristic.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.2
• /
• pp.46-51
• /
• 2009

Recently, microturbines have received attention as a small-scale distributed power generator. Since the exhaust gas carries all of the heat release, generating hot water is usual method of heat recovery from microturbine CHP (combined heat and power) systems. The power of microturbines decreases as ambient temperature increases. This study predicted micoturbine power boost by injecting hot water generated by heat recovery. Influence of injecting water at two different locations was examined. Water injection improves power, but efficiency depends much on the injection location. Injecting water at the compressor discharge shows a much higher efficiency than the combustor injection. However, the combustor injection may have as much available cogeneration heat as the dry operation, while the available heat in the compressor discharge injection is much smaller than the dry operation.