• Korean Journal of Veterinary Research
• /
• v.43 no.3
• /
• pp.457-461
• /
• 2003

A diagnosis of iodine-deficient goiter was confirmed in newborn piglets that were born hairless edematous, and with markedly enlarged thyroid gland. Clinically, most of the piglets were born dead, extreme weakness or dying within a few hours of birth. Gestation periods were prolonged for 3-7 days. Histopathologically, hair follicles were scarce and reduced in size, contained slender hairs, and revealed a shallow penetration into the hypodermis that showed severe diffuse edema. Thyroid glands had severely hyperplastic follicles and poorly staining colloid. The follicles were irregular in size and shape depending on varying amounts of lightly eosinophilic and granular colloid in the lumen. The iodine content of the diet fed to the sows and plasma total thyroxine and triiodothyronine concentration of sows were very low. This is a first report for iodine-deficient goiter in newborn piglets in Korea.

• Korean Journal of Materials Research
• /
• v.9 no.4
• /
• pp.434-438
• /
• 1999

Vickers microhardness for polished Cu specimen has been measured by conventional and new methods. The conventional microhardness was measured by observing the diagonal of indentation after the load was removed. Whereas, the new method for microhardness was obtained by measuring the penetration depth of indenter into the specimen under the load. As the applied load was increased, the microhardness obtained by new method was increased. When the applied load was in the range of 5mN to 80mN, the rate of elastic to total depth of indenter was about 6% and the calculated depth of rounded indenter was 0.07$\mu\textrm{m}$. The difference in microhardness measured by two different methods such as conventional and new methods can be explained in terms of the elastic deformation of specimen, the shape of practical indenter and pile up of material.

• Journal of ILASS-Korea
• /
• v.2 no.1
• /
• pp.36-45
• /
• 1997

A spray-wall impingement model for fuel sprays is proposed and implemented as a module into the KIVA-POSTECH code. The model is based on the single droplet experiments. The droplet behaviors after impingement are determined from experimental correlations. Different behaviors of impinged droplets depend on the wall temperature and the critical temperature of the fuel. Fuel film formation is taken into account so that the model can be applicable to any wall temperature and injection conditions. Computational results on a normal and on inclined wall are in good agreement for the spray shape and penetration. More validation against experiments and development of the heat transfer model are needed for further improvement.

• Fibers and Polymers
• /
• v.1 no.1
• /
• pp.45-54
• /
• 2000

Impact behaviors of the large deformable composites of Kevlar fiber reinforced composites of different preform structures have been investigated. An analytic tool was developed to characterize the impact behavior of the Kevlar composites. The image analysis technique, and deply technique were employed to develop energy balance equation under impact loading. An energy method was employed to establish the impact energy absorption mechanism of Kevlar multiaxial warp knitted composites. The total impact energy was classified into four categories including delamination energy, membrane energy, bending energy and rebounding energy under low velocity impact. Membrane and bending energy were calculated from the image analysis of the deformed shape of impacted specimen and delamination energy was calculated using the deplying technique. Also, the impact behavior of Kevlar composites under high velocity impact of full penetration of the composite specimen was studied. The energy absorption mechanisms under high velocity impact were modelled and the absorbed energy was classified into global deformation energy, shear-out energy, deformation energy and fiber breakage energy. The total energy obtained from the model corresponded reasonably well with the experimental results.

• Steel and Composite Structures
• /
• v.16 no.6
• /
• pp.595-609
• /
• 2014

The paper is reporting some comparisons between experimental and numerical results in terms of failure mode, failure time and ballistic properties of mild steel sheet. Several projectile shapes have been considered to take into account the stress triaxiality effect on the failure mode during impact, penetration and perforation. The initial and residual velocities as well as the failure time have been measured during the tests to estimate more physical quantities. It has to be noticed that the failure time was defined using a High Speed Camera (HSC). Thanks to it, the impact forces (average and maximum level), were analyzed using numerical simulations together with an analytical description coupled to experimental observations. The key point of the model is the consideration of a shape function to define the pulse loading during perforation.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.143-146
• /
• 2003

A finite element based on the efficient higher order zig-zag theory with multiple delaminations Is developed to refine the predictions of frequency and mode shapes. Displacement field through the thickness are constructed by superimposing linear zig-zag field to the smooth globally cubic varying field. The layer-dependent degrees of freedom of displacement fields are expressed in terms of reference primary degrees of freedom by applying interface continuity conditions including delaminated interfaces as well as free hounding surface conditions of transverse shear stresses. Thus the proposed theory is not only accurate but also efficient. This displacement field can systematically handle the number, shape, size, and locations of delaminations. Throught the dynamic version of variational approach, the dynamic equilibrium equations and variationally consistent boundary conditions are obtained. Through the natural frequency analysis and time response analysis of composite plate with multiple delaminations, the accuracy and efficiency of the present finite element are demonstrated. The present finite element is suitable in the predictions of the dynamic response of the thick composite plate with multiple delaminations.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.4 s.23
• /
• pp.5-13
• /
• 2005

The impact of a long-rod penetrator into oblique plates with combined obliquity and yaw is investigated. The study was done using a newly developed three dimensional dynamic and impact analysis code, which uses the explicit finite element method. Through the comparison of simulation result with experimental result and other code's result, the adaptability and accuracy of the developed code is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. As a result of comparison, it has found that deformed shape, residual length and velocity, rotational velocity of long-rod show good agreement with experimental data. Through this study, the applicability and accuracy of the code as a metallic armour system design tool is verified.

• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.317-324
• /
• 2001

This study deals with high power Nd:YAG laser welding of thin steels for small pressure vessels. Full penetration welding at the overlap joint was performed so as to assure sufficient weld strength. Results showed that mid-depth weld size reduced drastically with increasing the travel speed. Position of focus had little effect on the bead formation even though short focal system was used. However, the shape factor and the bead width had closely related with the position of focus. Based on the microstructural inspection, acceptable weld was obtained when the overlap clearance was controlled up to 20% of the base metal thickness. In the case that the joint contained more clearance than the critical value, both the tensile shear strength and the tear strength were reduced. Results also demonstrated that shielding gases were proved to play a key role as far as the bead formation characteristics was taken into consideration. Blowing dry air through 5mm in diameter nozzle produced narrower bead cross-section than that of argon or nitrogen shielding.

• Journal of the Korean Home Economics Association
• /
• v.24 no.3
• /
• pp.59-67
• /
• 1986

The heat of sewing needle is generated through the friction during the needle penetration into and withdrawal from fabrics. Therefore, effects of sewing condition for knitted fabric on the heat generation of needle was examined. The needle size was not the large influence factor of heat generation of needle but the needle point shape significantly affects needle temperature. And the super needle coated with fluoro resin had more effect on reducing the heat of needle. The decrease of sewing speed and the increase of stitch rate had more effect on the reduction in needle temperature. Also the Influence of a sewing thread on the needle temperature was very large compared with bare needle. As expected, an increase in the number of fabric layers result in higher needle temperature.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.15-20
• /
• 2020

This study aims to investigate injection rate and microscopic spray characteristics of diesel fuel containing fine air bubble (FBD). fine bubble was generated by cavitation theory using bubble generator. Fuel spray was injected into constant volume chamber and visualized by high speed camera. The injection rate data was acquired with bosch tube method. Injection rate of finebubble diesel was very similar with that of diesel. It showed slightly faster injection start by 5 ㎲ attributed to the low viscosity characteristics. In microscopic spray visualization, fine bubble diesel spray showed unsymmetric spray shape compared with diesel spray. It also showed very vigorous spray atomization performance during initial spray development. Improved atomization was also attributed to the low viscosity and surface tension of finebubble diesel fuel.