• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.7
• /
• pp.656-662
• /
• 2008

A cost-function based on manipulability and compatibility is designed to determine assembly motions of two cooperating manipulators. Assembly motions are planned along the direction maximizing performance indices to improve control performance of the two manipulators. This paper proposes bimanual task compatibility by defining cost functions. The proposed cost functions are applied and compared to the bimanual assembly task. The problem is formulated as a constrained optimization considering assembly constraints, position of the workpieces, and kinematics and redundancy of the bimanual robot. The proposed approach is evaluated with simulation of a peg-in-hole assembly with an L-shaped peg and two 3-dof manipulators.

• Therapeutic Science for Rehabilitation
• /
• v.11 no.4
• /
• pp.85-97
• /
• 2022

Purpose : This study aimed to investigate the effects of a digital pegboard training program with visual and auditory feedback on hand function and visual perception in stroke patients. Methods : Twenty two participants were randomly assigned to an experimental or control group. The experimental group received training using a digital pegboard training program with visual and auditory feedback (n=11), while traditional occupational therapy was administered to the control group (n=11). Hand function was assessed before and after the intervention using the Nine-Hole Peg Test and manual function test (MFT), while visual perception was assessed using the Motor-Free Visual Perception Test-3rd edition (MVPT-3). Results : Following the intervention, both the experimental and control groups showed significant improvements in performance in the Nine-Hole Peg Test and MVPT-3 (p<.05). The improvement on both tests was significantly greater in the experimental group than in the control group (p<.05). Conclusion : The results suggest that digital pegboard training with visual and auditory feedback may improve hand function and visual perception in stroke patients. Therefore, this intervention can be effective in occupational therapy to aid the recovery of stroke patients.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.211-215
• /
• 1989

This paper describes a dynamic robotic assembly system in which an industrial robot executes peg-in-hole task in a moving state. As an effective means to synchronize the end-effector of the robot with the moving conveyor this work uses a control algorithm which is essentially a PID position control scheme combined with velocity feedforward loop. A RCC wrist is used for the inserting task and its force responses are investigated for various tracking conditions and inserting velocities through a series of experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.244-249
• /
• 1989

For the robot manipulator in performing precision tasks, it is indispensable that the robot utilize the various sensors for intelligence. In this paper, the hybrid position/force control method is implemented with a force/torque sensor, two personal computers, and a PUMA 560 manipulator. Two application S/W packages for edge following and peg-in-hole tasks are developed by the proposed force control algorithm. The related experimental results are then presented and discussed,

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.31-35
• /
• 1986

Up to now, the most studies on the passive compliance system for assembly robot were only concerned about the device itself without through analysis of its concept. In this paper, we have tried to analyze a structural characteristics, in the case that the passive compliance system was used in simple assembly process like inserting a round shaft or peg into a round hole.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.25-31
• /
• 1995

In this paper, a direct drive scalar robot manipulator is constructed and its mechanical machanism for operation is explained. Also, a motion controller board for the direct drive robot manipulator was developed where the IBM 486 computer is the main controller. For the developed direct drive robot, a force/motion control algorithm based on an active compliance scheme is developed. A preliminary experiment using the developed direct drive for a peg-in-hole job was done by implementing the control algorithm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.427-431
• /
• 1996

A modeling of the dynamics of two cooperating robot manipulators doing assembly job such as peg-in-hole while coordinating the payload along the desired path is proposed. The system is uncertain due to the unknown mass and moment of inertia of the manipulators and the payload. To control the system, a robust control algorithm is proposed. The control algorithm includes fuzzylogic. By the fuzzy logic, the magnitude of the input torque of the manipulators is controlled not to go over the hardware saturation with keeping path tracking errors bounded.

• Journal of Korean Institute of Industrial Engineers
• /
• v.17 no.2
• /
• pp.75-86
• /
• 1991

This paper presents a methodology to enable the tolerances on mating parts of an assembly to be specified and be compatible to the precision of an assembly robot so as to achieve maximum system performance. The measure of performance is defined as the Probability of Successful Assembly (PSA). A typical loose fastener assembly, usually called peg-in-a-hole is investigated. The Geometric Tolerancing System is adopted to represent position tolerances of mating parts. Two models are presented by considering modifiers on a position tolerance, Regardless of Feature Size (RFS) and Maximum Material Condition (MMC). Using these models, it is analyzed how the Standard Limits and Fits recommended by ANSI influence the performance of an assembly robot. For this analysis, the Standard Limits and Fits are transformed to the representation scheme of the Geometric Tolerancing System. Due to low PSAs when the Standard Limits and Fits are taken into account, the effect of chamfers around a hole is also analyzed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.347-352
• /
• 2011

The maximum accuracy of position control by using an industrial robot is about $100{\mu}m$, whereas the maximum tolerated imprecision in the position of precision parts is about several tens of micrometers. Therefore, it is very difficult to assemble parts by position control only. Moreover, in the case of precision assembly, jamming or wedging can easily occur because of small position/orientation errors, which may damage the parts to be assembled. To overcome these problems, we investigated a force control scheme that provides proper motion in response to the contact force. In this study, we constructed a force control system that can be easily implemented in a position-controlled manipulator. Impedance control by using an admittance filter was adopted to perform stable contact tasks. It is shown that the precision parts can be assembled well by adopting impedance control and blind search methods.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3876-3881
• /
• 2012

In typical master/slave teleoperation systems, a human operator generally manipulates the master to control the slave through the visual information like camera image. However, the operator may get into trouble due to the limited visual information depending on the camera positions and the delay on the visual information because of low communication bandwidth. To cope with this inherit problem in the camera-based teleoperation system, this paper presents a teleoperation system using a reconstructed graphic model instead of the camera image. The proposed teleoperation system consists of a robot control module, a master module using a force-reflective joystick, and a graphic user interface (GUI) module. The graphic user interface module provides the operator with a 3D model reconstructed using a small set of sensing data received from the remote site. The proposed teleoperation system is evaluated through a peg-in-hole assembly task.