• Advances in concrete construction
• /
• 제3권4호
• /
• pp.283-293
• /
• 2015

This paper presents the effects of elevated temperatures of $400^{\circ}C$ and $800^{\circ}C$ on the residual compressive strength and failure behaviour of fibre reinforced concretes and comparison is made with that of unreinforced control concrete. Two types of short fibres are used in this study e.g., steel and basalt fibres. The results show that the residual compressive strength capacity of steel fibre reinforced concrete is higher than unreinforced concrete at both elevated temperatures. The basalt fibre reinforced concrete, on the other hand, showed lower strength retention capacity than the control unreinforced concrete. However, the use of hybrid steel-basalt fibre reinforcement recovered the deficiency of basalt fibre reinforced concrete, but still slightly lower than the control and steel fibres reinforced concretes. The use of fibres reduces the spalling and explosive failure of steel, basalt and hybrid steel-basalt fibres reinforced concretes oppose to spalling in deeper regions of ordinary control concrete after exposure to above elevated temperatures. Microscopic observation of steel and basalt fibres surfaces after exposure to above elevated temperatures shows peeling of thin layer from steel surface at $800^{\circ}C$, whereas in the case of basalt fibre formation of Plagioclase mineral crystals on the surface are observed at elevated temperatures.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.579-584
• /
• 1998

The purpose of this study is to evaluate the flexural strengthening effects of RC beams reinforced with carbon fiber sheets (CFS) in variable of strengthening amount and anchorage length of CFS. This study can be summarized as follows. The CFS shares the tensile stress such as rebar during loading test. Also, as the strengthening amount of CFS is increased, the maximum flexural strength of RC beams reinforced with CFS is increased. Therefore, it is confirmed that the CFS's strengthening method is very effective to improve the flexural strength of RC beams. The maximum flexural strength of RC beams with CFS is determined by bond failure between CFS and concrete surface. So, the evaluation of CFS's strengthening effect can be calculated using the tensile stress of CFS which is peeling. When the anchorage length of CFS. But, in case of same anchorage length of CFS, when the strengthening amount of CFA is increased, the ductility is decreased. Therefore, it is considered that the anchorage of CFS in the end zone is necessary.

• Journal of Pharmaceutical Investigation
• /
• 제32권2호
• /
• pp.107-112
• /
• 2002

To investigate the feasibility of developing a novel melatonin plaster, the effects of vehicles and drug loading dose on the in vitro permeation of melatonin across dorsal hairless mouse skin from pressure-sensitive adhesive (PSA) matrices were examined. Vehicles employed were propylene glycol laurate (PGL), propylene glycol monocaprylate (PGMC) and diethylene glycol monoethyl ether (DGME). Among PSAs used, only $Duro-Tak^{\circledR}$ 87-2196 showed a good peeling property. The release from $Duro-Tak^{circledR}$ 87-2196 was proportional to the square root of time, and dose-dependent. The fluxes increased as the loading dose increased over the doses under solubility. The relatively high permeation flux $(3.03{\pm}1.37\;{\mu}g/cm^2/hr)$ was obtained when using PGMC at the melatonin loading dose of $45\;mg/140\;cm^2$. Lag time was not affected by the vehicles used but by the thickness spread. The melatonin plasters prepared using PGMC showed a good adhesive property onto skin, and showed no crystal formation.

• 마이크로전자및패키징학회지
• /
• 제21권4호
• /
• pp.63-68
• /
• 2014

For a nanoscale Cu/low-k wafer, inter-layer dielectric (ILD) and metal layers peelings, cracks, chipping, and delamination are the most common dicing defects by traditional diamond blade saw process. Sidewall void in sawing street is one of the key factors to bring about cracks and chipping. The aim of this research is to evaluate laser grooving & mechanical sawing parameters to eliminate sidewall void and avoid top-side chipping as well as peeling. An ultra-fast pico-second (ps) laser is applied to groove/singulate the 28-nanometer node wafer with Cu/low-k dielectric. A series of comprehensive parametric study on the recipes of input laser power, repetition rate, grooving speed, defocus amount and street index has been conducted to improve the quality of dicing process. The effects of the laser kerf geometry, grooving edge quality and defects are evaluated by using scanning electron microscopy (SEM) and focused ion beam (FIB). Experimental results have shown that the laser grooving technique is capable to improve the quality and yield issues on Cu/low-k wafer dicing process.

• Bulletin of the Korean Chemical Society
• /
• 제32권12호
• /
• pp.4221-4226
• /
• 2011

Honeycomb-patterned polyvinypyrrolidone (PVP) thin films coated with nanometer-sized silver particles were prepared using honeycomb-patterned polystyrene (PS) template films fabricated by casting a polystyrene solution under humid condition. Silver was first metallized on the patterned PS films via silver nitrate ($AgNO_3$) reduction using tetrathiafulvalene (TTF) and a small amount of PVP as the reductant and dispersing agent, respectively. The effects of $AgNO_3$, TTF, and PVP solution concentrations during the reduction process in acetonitrile were determined to obtain a uniform silver-coated honeycomb-patterned PS film. Second, the silver-metallized patterned porous PS films were filled with high PVP concentration solutions via the spincoating process. Silver-coated patterned PVP films were obtained by peeling off the PVP layer from the template PS film after drying. The results show that the honeycomb-patterned PVP films uniformly coated with silver particles are conveniently obtained using the silver-coated patterned PS template, although the direct fabrication of these films using water droplets under humid conditions was not feasible because of the water solubility of PVP.

• 한국약용작물학회지
• /
• 제24권5호
• /
• pp.351-359
• /
• 2016

Background: We investigated the optimal aqueous extraction conditions for recovery of high yields of total phenolic compounds from roots of Arctium lappa L. (burdock, Asteraceae), and we compared their antioxidant capacity. Methods and Results: The antioxidant activity of the extracts was tested using 2,2-diphenyl-1-picrylhydrazyl, 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)-diammonium salt, and oxygen radical absorbance capacity assays. In addition, the major phenolic compounds present in the extracts were determined by high performance liquid chromatography analysis. Our results suggest that the roasted burdock $100^{\circ}C$, 15 min extract exhibited the strongest radical scavenging activity and possessed the highest concentration of phenolic compounds. The polyphenol content of both dried burdock and roasted burdock significantly increased with increase in the extraction temperature and time. Conclusions: These results indicated a relationship between phenolic compound levels in burdock and their free radical scavenging activities. This suggests that phenolic compounds significantly increase the antioxidant potential of burdock extracts.

• Corrosion Science and Technology
• /
• 제22권4호
• /
• pp.232-241
• /
• 2023

The mechanical properties of the hydrogen valve responsible for supplying and blocking hydrogen gas in a hydrogen fuel cell electric vehicle (FCEV) were researched. Mechanical properties by hydrogen embrittlement were investigated by coating chromium nitride (CrN) and titanium nitride (TiN) on aluminum alloy by arc ion plating method. The coating layer was deposited to a thickness of about 2 ㎛, and a slow strain rate test (SSRT) was conducted after hydrogen embrittlement to determine the hydrogen embrittlement resistance of the CrN and TiN coating layers. The CrN-coated specimen presented little decrease in mechanical properties until 12 hours of hydrogen charging due to its excellent resistance to hydrogen permeation. However, both the CrN and TiN-coated specimens exhibited deterioration in mechanical properties due to the peeling of the coating layer after 24 hours of hydrogen charging. The specimens coated at 350 ℃ presented a significant decrease in ultimate tensile strength due to abnormal grain growth.

• Safety and Health at Work
• /
• 제6권1호
• /
• pp.56-61
• /
• 2015

Frozen food processing workers work under a cold environment which can cause several adverse health effects.This study explored factors affecting workers' health in the frozen food industry in Thailand. Participants comprised 497 workers exposed to a cold working environment and 255 office workers who served as the controls. Data were collected by a survey on the work environment, and the interview of workers for abnormal symptoms. The exposed group had the following characteristics: 52.7% male, overall average age of 27 (SD 6.6) years old, attained elementary education (Grade 4 and Grade 6) (54.1%), married (48.9%), smokers (21.3%), alcohol consumption (31.0%), duration of work was between 1 and 5 years (65.2%), working 6 days a week (82.7%), 1-5 hours of overtime per week (33.8%), office workers (33.9%); work category: sizing (6.9%), peeling (28.3%) dissecting (22.2%), and in the warehouse (8.6%). The temperature in the work environment ranged from $17.2^{\circ}C$ to $19.2^{\circ}C$ in most sections, $-18.0^{\circ}C$ in the warehouse, and $25^{\circ}C$ in the office areas. Warehouse workers had more abnormal symptoms than controls including repeated pain in the musculoskeletal system (OR 11.9; 95% CI 6.12-23.45), disturbance throughout the body (OR 4.60; 95% CI 2.00-10.56), respiratory symptoms (OR 9.73; 95% CI 3.53-26.80), episodic finger symptoms (OR 13.51; 95% CI 5.17-35.33). The study results suggest that workers' health should be monitored especially with regard to back and muscle pain, respiratory symptoms, episodic finger symptoms, and cardiovascular symptoms. Health promotion campaigns such as antismoking and reduction of alcohol consumption should be established because smoking and alcohol consumption are contributing factors to the pathogenesis of Raynaud's phenomenon and peripheral vascular disorders such as hypertension and heart disease.

• Structural Engineering and Mechanics
• /
• 제58권3호
• /
• pp.577-596
• /
• 2016

FRP-concrete interfacial mechanical properties determine the strengthening effect of RC beams strengthened with FRP. In this paper, the model experiments were carried out with eight specimens to study the failure modes and the strengthening effect of RC beams strengthened with FRP. Then a theoretical model based on interfacial performances was proposed and interfacial mechanical behaviors were studied. Finite element analysis confirmed the theoretical results. The results showed that RC beams strengthened with FRP had three loading stages and that the FRP strengthening effects were mainly exerted in the Stage III after the yielding of steel bars, including the improvement of the bearing capacity, the decreased ultimate deformation due to the sudden failure of FRP and the improvement of stiffness in this stage. The mechanical formulae of the interfacial shear stress and FRP stress were established and the key influence factors included FRP length, interfacial bond-slip parameter, FRP thickness, etc. According to the theoretical analysis and experimental data, the calculation methods of interfacial shear stress at FRP end and FRP strain at midspan were proposed. When FRP bonding length was shorter, interfacial shear stress at FRP end was larger that led to concrete cover peeling failure. When FRP was longer, FRP reached the ultimate strain and the fracture failure of FRP occurred. The theoretical results were well consistent with the experimental data.

• 보존과학연구
• /
• 통권29호
• /
• pp.65-90
• /
• 2008

This study examines the status and the physical features of Paraloid B-72 layers with examination of microstructure and analysis of organic matters. Paraloid B-72 layers were coated on samples from the colour layer of outer wall painting in Mireuk hall in Geumsan temple. On the basis of the previous examination result, it has made the samples which are similar to outer wall in Mireuk hall in Geumsan temple. The samples can be divided into two, one; 5% Paraloid B-72 coating and another is without coating. Then samples have been experimented under the compulsive environments of infrared radiation and immersion, thereafter compared the results of the damages and physical features between two samples. As a result of the comparison, the sample with Paraloid B-72 had more serious cracks, exfoliations and peeling layers than that of without Paraloid B-72. Otherwise, in the examination of ultraviolet radiation, the sample with Paraloid B-72 coating showed weaker physical properties, less density in structure of colour layer and less hardness in surface of colour layer than the sample without coating. The percentage of moisture content after the ultraviolet radiation was higher in the sample without Paraloid B-72 than the sample with Paraloid B-72 coating. Observing the conditions before the ultraviolet radiation, the sample with Paraloid B-72 coating demonstrated lower rate in moisture evaporation rate than the sample without Paraloid B-72. As a consequence, in examination of this samples, the change of physical features are increased in the sample with Paraloid B-72 coating than that without Paraloid B-72 when compulsive environment of heat, moisture and ultraviolet rays for a short term are imposed.