• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Clinical and Experimental Pediatrics
• /
• v.45 no.5
• /
• pp.588-595
• /
• 2002

Purpose : The incidence of obesity has increased in Korea recently. Obesity leads to higher risks of hypertension, hyperlipidemia and insulin resistance. It also leads to risks of respiratory complications. This study was performed to see the effects of obesity on children's pulmonary functions and on developed bronchospasm after exercise loading according to their obesity degrees. Methods : 257 obese children and 150 non-obese children were enrolled. Obese children were divided into 3 groups by the obesity degrees. Pre- and post-exercise loading $FEV_1$(forced expiratory volume at one second), FVC(forced vital capacity) and PEFR(peak expiratory flow rate) were checked in all subjects. The percent predicted values of each parameter was compared according to obesity degrees and the differences between pre-exercise and post-exercise values. Results : The percent predicted value of $FEV_1$, FVC decreased only in the severe obesity group compared with those in the control group. However percent predicted PEFR declined according to obesity degrees. The percent predicted value of $FEV_1$, FVC and PEFR after exercise loading were much lower than those before exercise loading in all groups. Conclusion : As the degree of obesity was higher, the percent predicted value of pulmonary function was lower. And after exercise loading, as the degree of obesity was higher, the reduction of percent predicted value of pulmonary function was larger. Therefore the pulmonary function in obese children must be observed carefully. Further studies on the effects of pulmonary functions in obese children are necessary.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.1
• /
• pp.52-60
• /
• 2000

This study was conducted to gain basic data for alleviation of gas emission and conservation of healthy soil environment by investigating an aspect of gas emission and microbial diversity due to the supplement of different fertilizers after application with a livestock manure compost in greenhouse soils. Green pepper was cultivated in clay loamy soil from April to August. Before planting, a livestock manure compost was applied with $741mg\;ha^{-1}$ on the basis of the phosphate content contained in compost. And then, deficient nitrogen for cropping was supplemented with either quick-acting fertilizer of urea or a controlled slow release fertilizer made from urea formaldehyde(U/F). $NH_3$ and R $NH_2$ gases emitted from soil showed a low concentration in the early stage but a maximum in 27 days after planting, then decreased rapidly and not detected after 33 days. Their average concentrations were 42% and 85% lower in the treatment of slow release fertilizer than that of urea fertilizer, respectively. $CO_2$ gas emitted under urea fertilization was ranged from 1,200 to $3,200mg{\ell}^{-1}$ and that in slow release fertilizer was $900{\sim}2,650mg\;{\ell}^{-1}$. The average concentration of urea treatment was $2,260mg{\ell}^{-1}$ and 30% higher than that of slow release fertilizer. The treatment of slow release fertilizer with the lapse of cropping time populated larger in numbers of bacteria, actinomycetes, nitrate bacteria and nitrate reduction bacteria, and ratios of bacteria and actinmycetes to fungi than that of urea fertilizer. But the number of fungi was higher in the treatment of urea fertilizer and denitrifying bacteria showed a similar trend in both treatments. The microbial diversity index, which calculated with numbers of 6 species of microorganisms, was decreased with increasing of growing stage in the range of 0.1 to 0.35 and that was higher in the tratment of slow release fertilizer than urea.

• Journal of Fashion Business
• /
• v.9 no.6
• /
• pp.160-174
• /
• 2005

Despite the decrease in the number of children due to low birth rate, the domestic children's apparel market has been achieving steady growth as family income is rising thanks to more opportunities for working women, parents spend more on their children, and they prefer brand products that make their children look special. In addition, the market is suffering from hard competition as large enterprises have joined the race. The present study purposed to survey the children's apparel market in Korea, which is in a transitional period, and to contribute to the development of the market with Korean brands. For this purpose, we analyzed the characteristics of children's apparel brands in the 21st century based on the current state of the domestic children's apparel market and, based on the findings, forecasted the future trend of children's apparel brands, suggested improvements for expected problems, proposed standards for coping with changes such as diversification, high quality and differentiation in the children's apparel market, and provided consumers with information on how to purchase products. According to the result of analyzing the characteristics of children's apparel brands in the 21st century, brands are categorized largely into four types - life cultural brands, functional product brands, character brands and brands advancing to China. Life cultural brands equipped with all necessities for children are expanding, and with the deepening social problems of environmental pollution and the reduction of the child population, functional products made of environment-friendly materials are spreading widely, targeting infants and children. Furthermore, for extending age targets and diversifying products, children's apparel is using characters. The use of characters is expected to have a considerable effect on the growth of brands because children are more subjective as consumers than before and they are more easily persuaded with characters. Domestic children's apparel brands advancing to China have a high expectation of success in overcoming the limitation of the local market that has reached its peak and growing into global brands. Korean apparel makers are struggling to overcome the depressed domestic market, to recover consumers' consumption, to cope with market opening, to pursue high value of sensibility and to expand the seniors' market, etc. In this situation, future trends of children's apparel brands will be the expansion of family brands, brand totalization, quality price, niche market (pre-teen market), etc. In response to these trends, we made the following suggestions for improvement. 1. Children's apparel brands are evolving into family brands as well as into total brands through voluming. Today, however, apparel makers are advancing to the children's apparel market with the concept of adults' apparel and, as a result, children's apparel is merely adults' apparel of reduced size, having problems in design, color and materials. Thus, apparel makers must develop design considering the wide range of size and the characteristics of children's apparel, strengthen sourcing abilities to create revenues, and make thorough survey of customers to find common denominators between adults' apparel and children's apparel considering that characteristic that the target class is different from the buyer class. Furthermore, they must make active investments in human resources, develop outstanding products through advanced planning and design, and support marketing techniques and management systems to stores. 2. As the declining birth rate will continue to have a negative effect on the market, it may be difficult to expand the market size but there is still a margin for growth through high-sensibility and high-quality products. The competitiveness of brands is determined by their market shares. Accordingly, concepts should be specialized according to lifestyle, customers' diverse needs should be satisfied, and cross-coordination should be achieved within a brand. 3. Considering Korean parents who do not spare investment in their children despite shrinking consumption, functional products must be high value-added goods that can enhance efficiency. However, in the current situation of the infants' apparel industry where a textile manufacturer supply its products to multiple brands, it is difficult to develop unique products only based on materials. Thus, it is considered urgent to appeal to consumers not by relying on materials only but by finding methods of applying their own characters to children's dress.

• Journal of Korean Society of Forest Science
• /
• v.79 no.2
• /
• pp.115-126
• /
• 1990

This study was performed to find differences in phototaxis response of the larva, adult emergence, sex ratio and gall formation rate of Thecodiplosis japonensis Uchida et Inouye between two areas, north and south. Larvae from these two areas, Hweng-sung in north and Moo-an in south, both considered to be the sities of severe outbreak of the insect recently, were collected from the floor and transported to the entomology larboratory, Won-Kwang University in Iri, then overwintered. These larvae were used for various experimental purposes on various dates. The following results were obtained. 1. The sizes of larvae reached 2.45 in length, 0.70 in width for north, and 2.50 in length, 0.72 in width for sourth. It seems that the differents were not significant. 2. It is known that Leaving gall of larvae to the ground for the hibernation usually occurs on rainy days. For the larvae dispersion, the phototaxis response of the larvae was hypothesized. To check this, the author manipulated some different illumination intensities adjusting the distance between the glass tube in which 100 larvae were contained and electric bulb. The glass tubes were blackened all but except a small portion. The phototaxis responses between two areas seemed to be different particularly at low light intensities, 45, 145 and 1000 lux, The larvae from north assembled to the clear portion of the glass tube were more than 30 out of 100, however less than 30 in south sample regardless of the time passage. In either cases, the saturation points came after about 8 to 10 hours. If temperature units were used, the phototaxis curve= after 1 hour illumination between two areas provided significant differences. 3. The adult emergence of south area was lagged 10 days later than that of north area. The accumulated effective day-degrees of temperature for adult emergence were $934^{\circ}C$ for north area and $1180^{\circ}C$ for south area. The emerging duration of north area appeared to be in late May through the early of July and the peak emergence occurred in middle June that was approximately 15days earlier than that of south area. The sex ratio of female to male, regardless of area, was approximately 3 : 1. 4. The rates of gall formation of the red pine(Pinus densiflora Siebold et Zuccarini), 6-year-old seedlings, were as low as 9.94% for north area and 8.87% for south area. Through the close observation, the author presumed that the population reduction was greatly affected during the prepupa stage by relative moisture content and predators, such as spiders and ants presented on the ground.

• Journal of Energy Engineering
• /
• v.28 no.3
• /
• pp.65-79
• /
• 2019

The study attempted to estimate the optimal facility capacity by combining renewable energy sources that can be connected with gas CHP in industrial complexes. In particular, we reviewed industrial complexes subject to energy use plan from 2013 to 2016. Although the regional designation was excluded, Sejong industrial complex, which has a fuel usage of 38 thousand TOE annually and a high heat density of $92.6Gcal/km^2{\cdot}h$, was selected for research. And we analyzed the optimal operation model of CHP Hybrid System linking fuel cell and photovoltaic power generation using HOMER Pro, a renewable energy hybrid system economic analysis program. In addition, in order to improve the reliability of the research by analyzing not only the heat demand but also the heat demand patterns for the dominant sectors in the thermal energy, the main supply energy source of CHP, the economic benefits were added to compare the relative benefits. As a result, the total indirect heat demand of Sejong industrial complex under construction was 378,282 Gcal per year, of which paper industry accounted for 77.7%, which is 293,754 Gcal per year. For the entire industrial complex indirect heat demand, a single CHP has an optimal capacity of 30,000 kW. In this case, CHP shares 275,707 Gcal and 72.8% of heat production, while peak load boiler PLB shares 103,240 Gcal and 27.2%. In the CHP, fuel cell, and photovoltaic combinations, the optimum capacity is 30,000 kW, 5,000 kW, and 1,980 kW, respectively. At this time, CHP shared 275,940 Gcal, 72.8%, fuel cell 12,390 Gcal, 3.3%, and PLB 90,620 Gcal, 23.9%. The CHP capacity was not reduced because an uneconomical alternative was found that required excessive operation of the PLB for insufficient heat production resulting from the CHP capacity reduction. On the other hand, in terms of indirect heat demand for the paper industry, which is the dominant industry, the optimal capacity of CHP, fuel cell, and photovoltaic combination is 25,000 kW, 5,000 kW, and 2,000 kW. The heat production was analyzed to be CHP 225,053 Gcal, 76.5%, fuel cell 11,215 Gcal, 3.8%, PLB 58,012 Gcal, 19.7%. However, the economic analysis results of the current electricity market and gas market confirm that the return on investment is impossible. However, we confirmed that the CHP Hybrid System, which combines CHP, fuel cell, and solar power, can improve management conditions of about KRW 9.3 billion annually for a single CHP system.

• The Journal of Natural Sciences
• /
• v.1
• /
• pp.115-198
• /
• 1987

The present studies were undertaken to elucidate the influence of auxins, auxin-like substance-ethychlozate ("Figaron"),and pH and sort of rooting media on rooted propagation of certainornamental woody plant cuttings, and to see possible changes in internal compositions characterizing after root-promoting treatment as the cutting stage proceeded. The experimental check-up srevealed and summarized as seen in the following;I. Effect of three different auxin treatments on rooting cuttings: 1) Promotive influence of auxin varied according to different concentration levels, hours of dipping treatment of the auxins, and kind of plants. The greatest effect was obtained for Forsythia ksreana with NAA and IBA, for Ligustrurn obtusifolium var. variegatum with NAA and ethychlozate, for Hydrangea macrophylla, Magnolia kobus, and Magnolia liliflora with NAA, lBA and ethychlozate also. The most effective level of the promotive agents was found 200mg/l for NAA, 1000mg/l for IBA, and 200mg/l for ethychlozate. For Weigela florida and Gardenia jasminoides, range of the most effective level was shown relatively wide spread. 2) NAA was more effective at its optimal level of the rooting agent than ethychiozate for Weigela florida, Viburnum awabuki, Forsythia koreana, Acer palmatum 'Nomura', Bouga invillea glabra, Elaeagnus umbellata, Prunus tomentosa, Ligustrum obtusifolium, Pyracantha coccinea, Cestrum noctu rnum, Hydrangea macrophylla, Codiaeum variegatum, Rhododen dron lateritium, and Ilex crenata var. macrophylla, and yet ethychlozate was found either as equally as effective or more so than NAA for Zebrina pendula, Hibiscus syriacus, Fatshedera lizei, Schefflera arboricola, Campsis grandiflo ra, Ixora chinensis, Euonymus japonica, and Magnolia liliflora. On the contrary, no the auxin effect was noted with Lagerstroemia indica, Trachelospermum asiaticum, and Syringa vulgaris. This probably indicates that these species are genetically different for the auxin response.II. Effect of different pH and sorts of cutting media on rooting cuttings: 1) Bougainvillea showed best in rooting for the number and dry weight at pH 6.5, more with ethychlozate than NAA, while Ligustrum did at pH 5.0 more with NAA than ethychlozate. pH 4.0 medium resulted in the best rooting for Rhododendron with NAA, more than ethychlozate. 2) Use of cutting medium with peat: perlite: vermiculite = 1:1:1 showed to give the greatest rooting percent and dry weight, apart from considering the number of roots. This apparently meant the fact that cutting medium has more to do with root growth than root differentiation. Rhododendron yet showed results with cutting media that use of peat: perlite = 2:1 mixed is more effective on rooting than using peat alone.III. Effect of auxinic treatments on rooting cuttings and change in some cutting compositions: 1) Under the climatic conditions of July having temperature $26.3\pm$$2.4^{\circ}C$for cutting bed, new roots of Magnolia started to show up generally 20 days after the cutting was made, whereas Cestrum did much earlier than that, namely 14 days after. 2) Although total carbohydrate content of Magnolia cuttings showed no marked change without auxin treatment, it did so with the treatment, especially 30 days after the start of cutting. Cestrum cuttings demonstrated a gradual in crease in total carbohydrate content as rooting took place, and the content became reduced more with auxin than with out, just about when rooting proceeded to 14 days after the start of cutting. 3) Magnolia generally showed an increase in total nitrogen content as rooting proceeded more, and Cestrum showed a decrease in total nitrogen of cuttings. The auxin treatment exhibited no pertinent relation with change in plant nitro gen when rooting is promoted with auxin treatment. 4) An abrupt drop of total sugar and reducing sugar was noticed as Magnolia rooting started, and this reduction was parti cularly outstanding with auxin treatment. Starch content also was decreased in the later stage of cutting with auxin treatment, and was rather increased without auxin. Although sugar content soon increased as cutting started with auxin treatment in the case of Cestrum, it became reduced after rooting took place. 5) Total phenol content increased with rooting, and this was especially true when rooting started. This increase was reversed somehow regardless of auxin treatment. A decrease in phenol of Magnolia was found more striking with auxin than without in the later stage of the cutting period. 6)Avena coleoptile test for auxin-like substances presented the physiologically active factor is more in easy-to-root Magnolia liliflora than hard-to-root Magnolia kobus, and the activity of auxin-like substances was much increased with auxin treatment. The increase in the growth promoting substances was markedly pronounced when rooting just started. The active growth substances decreased in the later stage of cutting, and certain inhibitory substances started appearing. Cestrum also showed physiologically similar growth promoting substances accompanying auxin-like active substances if auxin is treated, and some strong inhibitory substances seemed to appear in the later stage of cutting. 7) Mung-bean-rooting test indicated biologically that endogenous growth substances in Magnolia all promoted mung-bean rooting, and activity of the growth substances apparently stimulated mung-bean rooting with auxin more than without. Here auxin treatment seemed to give a rise to an increased activity of endogenous growth substances in cuttings. This activity was found much greater with either NAA or IBA than ethychlozate, and showed its peak of the activity when rooting first started taking place. Certain inhibitory substances for Avena coleoptile growth strongly promoted mung-bean rooting, and it was also much like in the case of Cestrum.

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.404-412
• /
• 2011

The purpose of this study is to prepare extruded rice flours suitable for baking rice cookies. The extruded rice flours were prepared at 100 and 130$^{\circ}C$ temperature and 25 and 27% moisture content in a co-rotating twin screw extruder. The rice extrudates were dried at 100$^{\circ}C$ for 18 hr and subsequently ground into the fine flour. Characteristics of the extruded rice flours were examined by rapid visco analysis, hydration property analysis, differential scanning calorimetry (DSC), and in vitro digestion test. Water absorption, solubility, and swelling power of all extruded rice flours were higher than those of native rice flour. DSC analysis showed that native rice flour had a peak at about 65$^{\circ}C$ while all extruded rice flours did not show any peaks since they were already gelatinized during the extrusion proess. Viscosity of the extruded rice flours decreased with increasing temperature and lowering moisture content in the extrusion proess. The extruded rice flours prepared at 130$^{\circ}C$ exhibited lower viscosity than those prepared at 100$^{\circ}C$. The operating temperature of the extrusion proess was critical for the starch digestion in vitro. The extruded rice flours prepared at 130$^{\circ}C$ showed a rapid decrease in digestible starch content while an increased level of slowly digestible starch content was observed compared to those treated at 100$^{\circ}C$ in the extruder. Cookies were prepared with a mixture of wheat flour and extruded rice flours at the ratio of 7 to 3. The cookies made with the extruded rice flours had lower spread factor and darker yellow color than those prepared with wheat flour only. Hardness of the extruded rice flour-added cookies was similar to that of the wheat flour cookie whereas their overall acceptance was better. Therefore the rice cookies partially supplemented with extruded rice flours may have a potential as early childhood foods which require soft texture and allergy reduction.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.6
• /
• pp.489-495
• /
• 2020

Whereas the control of the hydration heat in mass concrete has been important as the concrete structures enlarge, many conventional strategies show some limitations in their effectiveness and practicality. Therefore, In this study, as a solution of controling the heat of hydration of mass concrete, a method to reduce the heat of hydration by controlling the hardening of cement was examined. The reduction of the hydration heat by the developed Phosphate Inorganic Salt was basically verified in the insulated boxes filled with binder paste or concrete mixture. That is, the effects of the Phosphate Inorganic Salt on the hydration heat, flow or slump, and compressive strength were analyzed in binary and ternary blended cement which is generally used for low heat. As a result, the internal maximum temperature rise induced by the hydration heat was decreased by 9.5~10.6% and 10.1~11.7% for binder paste and concrete mixed with the Phosphate Inorganic Salt, respectively. Besides, the delay of the time corresponding to the peak temperature was apparently observed, which is beneficial to the emission of the internal hydration heat in real structures. The Phosphate Inorganic Salt that was developed and verified by a series of the aforementioned experiments showed better performance than the existing ones in terms of the control of the hydration heat and other performance. It can be used for the purpose of hydration heat of mass concrete in the future.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.258-263
• /
• 2023

In this study, conductive polymers and the enzyme tyrosinase (Tyr) were deposited on the surface of a screen printed carbon electrode (SPCE), which can be fabricated as a disposable sensor chip, and applied to the detection of bisphenol F (BPF), an endocrine disruptor with proven links to male diseases and thyroid disorders, using electrochemical methods. On the surface of the SPCE working electrode, which was negatively charged by oxygen plasma treatment, a positively charged conductive polymer, poly(diallyldimethyl ammonium chloride) (PDDA), a negatively charged polymer compound, poly(sodium 4-styrenesulfonate) (PSS), and another layer of PDDA were layered by electrostatic attraction in the order of PDDA, PSS, and finally PDDA. Then, a layer of Tyr, which was negatively charged due to pH adjustment to 7.0, was added to create a PDDA-PSS-PDDA-Tyr sensor for BPF. When the electrode sensor is exposed to a BPF solution, which is the substrate and target analyte, 4,4'-methylenebis(cyclohexa-3,5-diene-1,2-dione) is generated by an oxidation reaction with the Tyr enzyme on the electrode surface. The reduction process of the product at 0.1 V (vs. Ag/AgCl) generating 4,4'-methylenebis(benzene-1,2-diol) was measured using cyclic and differential pulse voltammetries, resulting in a change in the peak current with respect to the concentration of BPF. In addition, we compared the detection performance of BPF using an ionic liquid electrolyte as an alternative to phosphate-buffered saline, which has been used in many previous sensing studies. Furthermore, the selectivity of bisphenol S, which acts as an interfering substance with a similar structure to BPF, was investigated. Finally, we demonstrated the practical applicability of the sensor by applying it to analyze the concentration of BPF in real samples prepared in the laboratory.