• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.129-134
• /
• 2007

The purpose of this study was to determine the variability of components of the vertical ground reaction force signal to seek the suitable number of attempt datum to be analyzed during running at 2m/s and 4m/s. For this study, six subjects (height mean:$174.5{\pm}4.4cm$, weight $671.5{\pm}116.4N.$, age:$25.0{\pm}yrs.$) were selected and asked to run at least 3 times each run condition randomly. FFT(fast Fourier transform) was used to analyze the frequency domain analysis of the vertical ground reaction forces signal and an accumulated PSD (power spectrum density) was calculated to reconstruct the certain signal. To examine the deviation of the vertical ground reaction between signals collected from an different number of attempt, variability of frequency, magnitude of passive peak, time up to the passive peak and maximum load rate were determined in a coefficient of variance. The variability analysis revealed that when analyze the vertical reaction force components at 2m/s speed running, which belongs to slow pace relatively, it would be good to calculate these components from signal of one attempt, but 4m/s speed running needs data collected from two attempts to decrease the deviation of signal between attempts. In summary, when analyzing the frequency and passive peak of the vertical reaction force signal during the fast run, it should be considered the number of attempt.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.136-138
• /
• 2005

High-performance frontal analysis (HPFA) was used for the determination of the binding constant of Sibuprofen to human serum albumin (HSA). This experiment was based on an Inertsil 100 Diol 5 column and sodium phosphate buffer (pH 7.4 and ionic strength of 0.17) as the mobile phase. The mixture of S-ibuprofen and HSA (70 $\mu$M) solution were directly injected into the HPFA column. An injection volume of 200 $\mu$L and a “estricted injection”method were applied to ensure the drug to be eluted as a zonal peak with a plateau. The unbound drug concentration was calculated from the peak height of the zonal peak. Scatchard analysis was used for evaluation of the binding constant (K) and binding affinity (nK) of S-ibuprofen to HSA, and the results were K = 2.833 ${\times}$ 10$^4$ [L mol$^{-1}$], nK = 4.935 ${\times}$ 10$^4$ [L mol$^{-1}$], respectively.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.6
• /
• pp.583-588
• /
• 2008

Swell data observed in the East Sea in February, 2008 were analyzed using wavelet method. The wavelet analyzed results show detailed time series variation of wave group, peak frequency and spectrum. The comparison of time averaged wavelet spectrum with fourier spectrum turn out to be very similar in terms of spectrum shape and peak frequency evolution but the peak frequency wave energy and the significant wave height show discrepancies. Wavelet analysis can detect the change of spectrum in time as well as in frequency and very efficient to study transient and irregular phenomena such as freak waves and abnormal swells in the ocean. More analysis with more wave data are needed for future application.

• The Journal of Korean Physical Therapy
• /
• v.14 no.2
• /
• pp.172-180
• /
• 2002

The purpose of this paper was to make an analysis of anaerobic power in professional female basketball players using the Wingate Test Method with bicycle ergometer. Twenty-three subjects(age $21.6\pm2.8years$, body height $178.0\pm7.4cm$, body weight $70.3\pm7.4kg$) were selected from professional female basketball team whose careers were over 10years and participated in this investigation. Each subject peformed a Wingate anaerobic power test to determine total work, peak power, mean power, fatigue index and blood lactate concentration. The following were obtained from result data analysis; 1. The Total Work of athletes was a $1128.7\pm120.6watt$ 2. The Peak Power of athletes was a $449.5\pm53.1watt$ 3. The Mean Power of athletes was a $369.1\pm39.4watt$ 4. The Fatigue Index of athletes was a $33.5\pm6.9\%$ 5. The blood lactate concentration was $1.85\pm0.85mM/L$ at the normal state and $3.16\pm1.53mM/L$ at the after Wingate test. The blood lactate concentration was $6.96\pm0.81mM/L$ after 3 minute and $6.95\pm1.05mM/L$ after 5 minutes.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.5
• /
• pp.816-821
• /
• 1994

The physicochemical properties and cooking qualities of six cultivars of covered barley, four malting barley and six naked barley were investigated. The 1, 000 kernel weight was heavier in the malting barley and ash content was the highest in covered barley. The varietal variation of amylose content was 17.7 to 20.2%. $\beta$-Glucan viscosity was generally lower in the malting barely, and varied greatly among barley cutivars with 2.16 to 8.47 cSt. The pearling rate was highest in naked barley with a mean of 75.5% and protein content of aw and pearled barely was significantly different with cultivars. In the cultivars tested, Doosan 8, Youngsan and Iri 5 showed the higher milling rate. Amylose patterns showed that the covered barley cultivars has lower gelatinization temperature and higher peak height and height at 50 $^{\circ}C$ than the malting and naked barley. The water absorptions were highest in covered barley cultivars , and lowest in naked barley cultivars. The soluble solid was highest in naked barley cultivars.

• The Journal of Korean Physical Therapy
• /
• v.28 no.5
• /
• pp.269-273
• /
• 2016

Purpose: This study was conducted to examine the effect of kinesio taping (KT) on vertical jumping performance. Methods: Young women (n=24) performed vertical jumping under three conditions: kinesio taping, placebo taping, and no taping. All tapes were applied to both quadriceps and the gastrocnemius of the subjects. Vertical jump height and power were measured using an OptoGait, and the non-parametric Friedman test was used to identify differences between conditions. Results: No significant differences in maximum jump height or peak jump power between were observed between taping conditions. Conclusion: The results showed that KT did not facilitate muscle performance by generating higher jumping power or yielding a better jumping performance. As the functional performance is related to muscle strength, this finding may be explained by the fact that KT has no effects on muscle strength.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.431-436
• /
• 2005

In this paper, We proposed the stereo image modeling using 2-dimensional images captured by the high resolution cameras to inspect the ball defects of BGA(Ball Grid Array) device. The proposed algorithm consists of the package/ball area extraction part, the FOV(Field of View) calibration part, the top point matching part, and ball height measurement part, In the package/ ball area extraction part, the package and ball areas are separately extracted in a left and right image by the extraction algerian. Through the experiment, we draw out the result.

• Earthquakes and Structures
• /
• v.15 no.2
• /
• pp.203-214
• /
• 2018

Deflection control in tall buildings is a challenging issue. Connecting of the towers is an interesting idea for architects as well as structural engineers. In this paper, two reinforced concrete core-wall towers are connected by a truss bridge with buckling restrained braces. The buildings are 40 and 60-story. The effect of the location of the bridge is investigated. Response spectrum analysis of the linear models is used to obtain the design demands and the systems are designed according to the reliable codes. Then, nonlinear time history analysis at maximum considered earthquake is performed to assess the seismic responses of the systems subjected to far-field and near-field record sets. Fiber elements are used for the reinforced concrete walls. On average, the inter-story drift ratio demand will be minimized when the bridge is approximately located at a height equal to 0.825 times the total height of the building. Besides, because of whipping effects, maximum roof acceleration demand is approximately two times the peak ground acceleration. Plasticity extends near the base and also in major areas of the walls subjected to the seismic loads.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.4
• /
• pp.355-359
• /
• 1999

This paper presents a method for determining machining parameters in electrical discharge machining process (EDM) based on discharge area. The parameters are the peak value of currents, the pulse-on time, and the pulse-off time, on which the EDM performance depends chiefly. The optimal machining parameters are closely related on discharge area, which can be calculated from a tool electrode and a discharge height. In the paper the discharge area is obtained from NC code for machining the tool electrode instead of its geometric model. The method consists of following three steps. First a Z-Map model is constructed from the NC code. Secondly, the discharge area is obtained from the Z-Map model and a Z-height. Finally, the machining parameters are calculated from the discharge area. An introduced example shows that the machining parameters are calculated by the using a Z-map model obtained from the machining data for a tool electrode.

• KIEAE Journal
• /
• v.2 no.3
• /
• pp.33-38
• /
• 2002

The intermediate range of temperatures($100{\sim}300^{\circ}C$) which can be achieved with CPCs(Compound Parabolic Concentrators) without tracking device provides both economic and thermal advantages for solar collector design. The present paper summarizes critical design considerations for CPC with cylindrical absorber and its optical performance using ray tracing program. Concentration ratios vary as acceptance half angle, ratio of reflector height to aperture width and ratio of reflector area to aperture area. This effects showed that the concentration ratio was increased as acceptance angle but optimum ratio of reflector height to aperture width existed at critical value. As a result of ray tracing, solar ray losses was maximized at acceptance half angle and this problem was solved by increasing absorber tube diameter. The concentrating flux distribution on the absorber surface was uniform but peak flux existed.