• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.756-761
• /
• 2013

This paper propose the new demodulation method that can detect resolver signal's peak at the time of position estimation when the position information is required during current controller period. The proposed method is performed in a synchronous demodulation way with exciting signal and also cover a capability which can compensate the lag element of exciting signal caused by the resolver's inductive component and filter circuit. This paper carried out the experiment to investigate the validity and performance of the suggested method by using the test board made up of DSP and demodulation circuit. The test results show that the proposed method is theoretically clear and work completely as expected from making sure of sampling resolver signal's peak at the time of position estimation. In addition, Software position tracking algorithm is executed with the demodulated signals generated by the suggested method and an exact position can be estimated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.8
• /
• pp.1204-1209
• /
• 2012

To diagnose dental pulp vitality, electric pulp tester has been widely used, which is a method to test condition of nerve. However, especially in the case of patients with trauma, nerve desensitization could temporarily occur even though nerve might be recovered by blood flow within the pulp later, which implies that blood flow in dental pulp is also an important factor for diagnosing vitality. This paper described the development of a probe that relatively measured blood flow in dental pulp using photoplethysmography (PPG). The probe emits four different wavelength light sources including three visible and an infrared light. We tested which light source detect sensitively the blood flow in dental pulp. As a result, green light had the largest peak to peak voltage and the power spectrum among different wavelengths.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.285-289
• /
• 2006

In this paper, a design and implementation of GPS/Galileo software receiver is given. As a GPS receiver, it is able to perform every function of receiver such as acquisition, code and carrier tracking, navigation bit extraction, navigation data decoding, pseudorange calculations, and position calculations. A method to acquire and track the Galileo BOC(1,1) signal is also required because the correlation of BOC(1,1) signal has multiple peaks different from that of GPS signal. Therefore, a method to detect the main-peak in correlation function of BOC signal is required to avoid false acquisition. In this paper, very-early, very late correlation is implemented to track the correct main peak. The performance of implemented GPS/Galileo software receiver with BOC(1,1) signal tracking feature is evaluated with GPS/Galileo IF signal generator.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.50 no.3
• /
• pp.140-145
• /
• 2001

The instantaneous voltage drop is occurred when the fault is happened on the nearby feeders. The instantaneous voltage drop is continued during relatively short period. But, the effect of it can be very severe to some sensitive devices. That is, it can be the reason of restart or malfunction of some devices. And these phenomenons can cause the enormous economical damage and shorten the lifetime of the devices. In this paper, the device which can compensate the instantaneous voltage drop, is studied. Through the computer simulation using PSCAD/EMTDC, the validity of the control algorithm using peak detection method is verified. And the Dynamic Voltage Restorer(DVR) prototype is designed and constructed. Through the experiment, the function and performance of the DVR prototype is verified.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.51-53
• /
• 2002

This research aims to develop a multiple channel electrochemical DNA chip using micro-fabrication technology. At first, we fabricated a high integrated type DNA chip array by lithography technology. Several probe DNAs consisting of thiol group at their 5-end were immobilized on the sold electrodes. Then target DNAs were hybridized by an electrical force. Redox peak of cyclic-voltammogram showed a difference between target DNA and mismatched DNA in the anodic peak current. Therefore, it is able to detect a various genes electrochemically after immobilization of a various probe DNA and hybridization of label-free DNA on the electrodes simultaneously. It suggested that this DNA chip could recognize the sequence specific genes.

• Structural Engineering and Mechanics
• /
• v.17 no.3_4
• /
• pp.331-346
• /
• 2004

A new sensor system is proposed for measuring damage indexes. The damage index is a physical value that is well correlated to a critical damage in a device or a structure. The mechanism proposed here utilizes elastic buckling of a thin wire and does not require any external power supply for memorizing the index. The mechanisms to detect peak strain, peak displacement, peak acceleration and cumulative deformation as examples of damage indexes are presented. Furthermore, passive and active wireless data retrieval mechanisms using electromagnetic induction are proposed. The passive wireless system is achieved by forming a closed LC circuit to oscillate at its natural frequency. The active wireless sensor can transmit the data much further than the passive system at the sacrifice of slightly complicated electric circuit for the sensor. For wireless data retrieval, no wire is needed for the sensor to supply electrical power. For the active system, electrical power is supplied to the sensor by radio waves emitted from the retrieval system. Thus, external power supply is only needed for the retrieval system when the retrieval becomes necessary. Theoretical and experimental studies to show excellent performance of the proposed sensor are presented. Finally, a prototype damage index sensor installed into a 7 storey base-isolated building is explained.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.1
• /
• pp.227-232
• /
• 2011

The QRS complex in ECG analysis is possible to obtain much information that is helpful for diagnosing different types of cardiovascular disease. This paper presents the preprocessor method to detect R-peak, RR interval, and HRV in wireless sensor node. The derivative of the electrocardiogram is efficiency of preprocessing method for resource hungry wireless sensor node with low computation. We have implemented R-peak and RR interval detection application based on dECG for wireless sensor node. The sensor node only transfers meaning parameter of ECG. Thus, implementation of sensor node can save power, reduce traffic, and eliminate congestion in a WSN.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.51-56
• /
• 2000

Demand for new nondestructive evaluations is growing to detect tensile crack growth behavior to predict long term performance of materials and structure in aggressive environments, especially when they are in non-visible area. Acoustic emission technique is well suited to these problems and has drawn a keen interests because of its dynamic detection ability, extreme sensitivity and location of growing defects. In this study, we analysed acoustic emission signals obtained in tensile test of high strength fire resistance steel for frame structure with time frequency analysis methods. The results obtained are summaries as follows ; In the T and TN specimen consisting of ferrite and pearlite grains, most of acoustic emission events were produced near yield point, mainly due to the dislocation activities during the deformation. However, B specimen under $600^{\circ}C$ - 10min had a two peak which was attribute to the presence of martensite phase. The first peak is before yield point the second is after yield point. The sources of second acoustic emission peak were the debonding of martensite-martensite interface and the micro-cracking of brittle martensite phase. In $600^{\circ}C$-30min to $700^{\circ}C$-60min specimens, many signals were observed from area before yield point and counts were decreased after yield point.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.1
• /
• pp.1-5
• /
• 2013

The two major problems related to the blood flow in replaced prosthetic heart valve are thrombus formation and hemolysis. Reliability of prosthetic valve is very important because its failure means the death of patient. There are many factors affecting the valvular failures and their representatives are mechanical failure and thrombosis, so early noninvasive detection is essentially required. The purpose of this study is to detect the various thromboses formation by using acoustic signal acquisition and its spectral analysis on the frequency domain. We made the thrombosis models using Polydimethylsiloxane (PDMS) and they are thrombosis model on the disc, around the sewing ring and fibrous tissue growth across the orifice of valve. Using microphone and amplifier, we measured the acoustic signal from the prosthetic valve, which is attached to the pulsatile mock circulation system. A/D converter sampled the acoustic signal and the spectral analysis is the main algorithm for obtaining spectrum. Then the spectrum of normal and 5 different kinds of abnormal valve were obtained. Each spectrum waveform shows a primary and secondary peak. The secondary peak changes according to the thrombus model. To quantitatively distinguish the frequency peak of the normal valve from that of the thrombosed valves, analysis using a neural network was employed. Acoustic measurement has been used as a noninvasive diagnostic tool and is thought to be a good method for detecting possible mechanical failure or thrombus.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.9
• /
• pp.1321-1325
• /
• 2004

Sodium dodecyl sulfate (SDS), an anionic surfactant, can strongly adsorb at the surface of a carbon paste electrode (CPE) via the hydrophobic interaction. In pH 3.0 $Na_2HPO_4$-citric acid buffer (Mcllvaine buffer) and in the presence of SDS, the cationic indole-3-acetic acid (IAA, $pK_a$ = 4.75) was highly accumulated at the CPE surface through the electrostatic interaction between the negative-charged head group of SDS and cationic IAA, compared with that in the absence of SDS. Hence, the oxidation peak current of IAA increases greatly and the oxidation peak potential shifts towards more negative direction. The experimental parameters, such as pH, varieties of surfactants, concentration of SDS, and scan rate were optimized for IAA determination. The oxidation peak current is proportional to the concentration of IAA over the range from $5\;{\times}\;10^{-8}$ mol/L to $2\;{\times}\;10^{-6}$ mol/L. The detection limit is $2\;{\times}\;10^{-8}$ mol/L after 3 min of accumulation. This new voltammetric method was successfully used to detect IAA in some plant leaves.