• Clean Technology
• /
• v.21 no.3
• /
• pp.184-190
• /
• 2015

Most of LNT catalysts use noble metals such as Pt for low temperature NO_x oxidation but there is an economic weakness. For the purpose of overcoming this, this study is to develop DeNO_x catalyst for LNT excluding PGM (platinum group metal) such as Pt, Pd, Rh, etc. To do so, Al/Co/Ni catalyst selected as a preliminary test is used to study fundamental property and NO_x’s conversion according to calcined temperature. Ultimately, that is, Al/Co/Ni mixed metal oxide which does not use PGM is selected and physicochemical characterization is performed by way of XRD, EDS, SEM, BET and ramp test and NO_x conversion is also analyzed. This study shows that all samples consist of mixed oxides of spinel structure of Co₂AlO₄ and NiAl₂O₄ and have enough pore volume and size for redox. But as a result of NH₃-TPD test, it is desired that calcined temperature needs to be maintained at 700 ℃ or lower. Also only samples which are processed under 500 ℃ satisfied NO and NO_x conversion simultaneously through ramp test. Based on this study’s results, optimum calcined temperature for Al/Co/Ni=1.0/2.5/0.3 mixed metal oxide catalyst is 500 ℃.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.382-387
• /
• 2018

In this study, the reaction characteristics of combined steam and carbon dioxide reforming of methane (CSCRM) reaction using Pd-Ni-YSZ catalyst were investigated according to types of catalysts and gas compositions. Catalysts were prepared in the form of powder and porous disk. The injected gases were supplied at different ratios of $CH_4/CO_2/H_2O$. As a result, the conversion of $CH_4$ and $CO_2$ was improved as a result of using the porous disc type catalyst as compared with that of the powder type catalyst. When the $CH_4/CO_2/H_2O$ ratio of the feed gas was 1 : 0.5 : 0.5, the $H_2/CO$ ratio was adjusted close to 2. However, after 6 hours of the reaction, $CH_4$ conversion was partially reduced by the carbon deposition and the pressure drop increased from 0.1 to 0.8. This issue was then solved by optimizing the water content. As a result, it was confirmed that the durability was secured by preventing the carbon deposition when the gas was supplied at a $CH_4/CO_2/H_2O$ ratio of 1 : 0.5 : 1, and the conversion rate was maintained at a relatively high level.

• Korean Journal of Metals and Materials
• /
• v.56 no.12
• /
• pp.910-914
• /
• 2018

Since catalyst technology is one of the promising technologies to improve the working performance of next generation energy and electronic devices, many efforts have been made to develop various catalysts with high efficiency at a low cost. However, there are remaining challenges to be resolved in order to use the suggested catalytic materials, such as platinum (Pt), gold (Au), and palladium (Pd), due to their poor cost-effectiveness for device applications. In this study, to overcome these challenges, we suggest a useful method to increase the surface area of a noble metal catalyst material, resulting in a reduction of the total amount of catalyst usage. By employing block copolymer (BCP) self-assembly and nano-transfer printing (n-TP) processes, we successfully fabricated sub-20 nm Pt line and cross-bar patterns. Furthermore, we obtained a highly ordered Pt cross-bar pattern on a Ni thin film and a Pt-embedded Ni thin film, which can be used as hetero hybrid alloy catalyst structure. For a detailed analysis of the hybrid catalytic material, we used scanning electron microscope (SEM), transmission electron microscope (TEM) and energy-dispersive X-ray spectroscopy (EDS), which revealed a well-defined nanoporous Pt nanostructure on the Ni thin film. Based on these results, we expect that the successful hybridization of various catalytic nanostructures can be extended to other material systems and devices in the near future.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1079-1085
• /
• 1999

An investigation was made of the effect of various transition metal catalysts, ligands, and a promoter on the synthesis of N,N'-diphenylurea(DPU) from nitrobenzene, aniline, and carbon monoxide. Homogeneous Pd and Ni catalysts were found to be highly efficient, giving almost quantitative isolated DPU yields at 100% nitrobenzene conversion. Bidentate ligand, 1,3-bis(diphenylphosphino)proane(dppp) showed much improved activity and significantly different reactivity relative to the usual monodentate $PPh_3$ ligand in the presence of Ni and Pd catalysts. These results were inferred to the effect of the cis coordination of bidentate dppp ligand on the metal. The use of a promoter $Et_4NCl$ was indispensable in the case of $PPh_3$, yet inhibited the reaction if used with dppp. It was possible to reuse the Pd-dppp catalyst system, although the catalytic activity was reduced slowly.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.6
• /
• pp.822-829
• /
• 1997

A catalytic burner was studied which can be used as a heater operated in medium temperature. Noble metal catalysts (Pd/NiO) were used, which were supported on alumina wash coated honeycomb. The maximum heat-resisting temperature of the catalyst is about 900.deg. C. Combustion efficiency of the catalytic burner reached more than 99.5 % at the excess air ratio above 1.25.NOx emissions were lower than 1.0 ppm at all operation conditions. The operation condition for a stable catalytic combustion was obtained. It was dependent on the catalyst thickness. The 30 mm thick catalyst showed the widest stable catalytic combustion region. Stable catalytic combustion region of 30 mm thick catalyst was the operation condition of excess air ratio 1.25 - 1.75 and heat flux 7 - 14 kcal/h center dot cm$^{2}$.

• Carbon letters
• /
• v.3 no.3
• /
• pp.146-151
• /
• 2002

Activated carbon fibers were prepared from the petroleum isotropic pitch and organometallic compounds. The metalsvwere dispersed uniformly in the ACFs. The specific surface area and pore size distributions of metal containing ACFsvwere measured. The mesopores of ACFs were developed by Co, Ni, and Mn metals addition and the catalytic reactivityvof ACFs'SOx removal was increased by adding Ni and Pd metals. It was found that the mesopores did not work forvthe improvement of catalytic reactivity of ACFs' SOx removal with the blank experiment using the metal removedvACFs.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.5
• /
• pp.535-548
• /
• 2023

The intermittent nature of renewable energy is a challenge to overcome for safety and stable performance in water electrolysis systems linked to renewable energy. Oxygen removal using the catalyst is suitable for maintaining the oxygen concentration in hydrogen below the explosive level (4%) even in intermittent power supply. Metals such as Pd, Pt, and Ni are expected to be effective materials due to their hydrogen affinity. The oxygen removal performance was compared under high hydrogen concentration conditions by loading on γ-Al₂O₃ with high reactivity and large surface area. The characteristics of the catalyst before and after the reaction were analyzed through X-ray diffraction, transmission electron microscope, H₂-temperature programmed reduction, X-ray photoelectron spectroscope, etc. The Pd catalyst that showed the best performance was able to lower 2% oxygen to less than 5 ppm. Changes in catalyst characteristics after the reaction indicate that oxygen vacancies are related to oxygen removal performance and catalyst deactivation.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.50-54
• /
• 2018

This study investigated the long-term durability of catalyst(Pd or Fe)-infiltrated solid oxide cells for $CO_2$/steam co-electrolysis. Fuel-electrode supported solid oxide cells with dimensions of $5{\times}5cm^2$ were fabricated, and palladium or iron was subsequently introduced via wet infiltration (as a form of PdO or FeO solution). The metallic catalysts were employed in the fuel-electrode to promote $CO_2$ reduction via reverse water gas shift reactions. The metal-precursor particles were well-dispersed on the fuel-electrode substrate, which formed a bimetallic alloy with Ni embedded on the substrate during high-temperature reduction processes. These planar cells were tested using a mixture of $H_2O$ and $CO_2$ to measure the electrochemical and gas-production stabilities during 350 h of co-electrolysis operations. The results confirmed that compared to the Fe-infiltrated cell, the Pd-infiltrated cell had higher stabilities for both electrochemical reactions and gas-production given its resistance to carbon deposition.

• Journal of the Korean Chemical Society
• /
• v.38 no.4
• /
• pp.295-301
• /
• 1994

The Ru(Ⅲ), Ni(Ⅱ), Cu(Ⅱ), and Pd(Ⅱ) complexes of N$_4$-polydentate ligands(meso-Me$_6$-[14]-ane, rac-Me$_6$-[14]-ane, and cyclam) have been prepared and their catalytic activity and selectivity in the oxidation of olefins in the presence of oxidant such as NaOCl, H$_2$O$_2$, t-BuOOH, and PhIO studied. The oxidations of cyclohexene, 1-hexene, cyclooctene, 1-octene, and styrene as substrates have been investigated gas chromatographically. The Ru(Ⅲ)-N$_4$ complexes showed high selectivity for epoxide in the catalyzed oxidation of olefins with NaOCl. The catalytic activities of Ru(Ⅲ)-N$_4$ complexes were discussed in terms of the flexibility of N$_4$-polydentate ligands, the Ru(Ⅲ)-Cl bond interaction and the steric effect of oxidants. The oxidation of 1-octene using PhIO as oxidant was carried out to verify. The Pd(Ⅱ) complex turned out to be more active catalyst than the Ni(Ⅱ) complexes.

• Textile Coloration and Finishing
• /
• v.22 no.1
• /
• pp.77-82
• /
• 2010

Highly conductive yarn was successfully obtained using electroless nickel plating method with palladium activation. In the presence of palladium seed on surface of fibers as a catalyst, continuos nickel layer produced on surface of fibers by reducing $Ni${2+}$ ion in the electroless plating bath to $Ni^0$. It was found that the Pd-activation using $SnCl_2$ and $PdCl_2$ to deposit palladium seeds on the surface of fibers plays a key role in the subsequent electroless plating of nickel. It also found that electroless nickel plating on the fibers can induce the nickel-plated $ELEX^{(R)}$ fibers to improve the electrical conductivity of the fibers. The thickness of nickel coating layer on the Pd-activated $ELEX^{(R)}$ fibers and specific conductivity of the fiber were increased through electroless plating time. The temperature of nickel plating bath was very effective to enhance the nickel deposition rate.