• 한국전기전자재료학회논문지
• /
• 제20권4호
• /
• pp.294-302
• /
• 2007

We studied on possibility of the application of photolithography technique to patterning the organic active layer poly(3-hexylthiophene) (P3HT). In the case of selective etching method, we made thin oxide film on P3HT thin film using $O_2$ treatment. We achieved the field-effect mobilities in the saturation regime ${\sim}1.2{\times}10^{-3}\;cm^2/V{\cdot}s$, $I_{on/off}$ ratios ${\sim}10^5$ in the selective etching method, ${\sim}7.4{\times}10^{-4}cm^2/V{\cdot}s$, $I_{on/off}$ ratios ${\sim}5{\times}10^3$ in the lift-off one. These values are higher than ones of the unpatterned P3HT-based OTFTs. On the basis of the above results, we demonstrate the photolithographic patterning for P3HT active layer is successfully carried out without degradation of P3HT.

• 한국재료학회지
• /
• 제29권4호
• /
• pp.228-232
• /
• 2019

Copper electroplating and electrode patterning using a screen printer are applied instead of lithography for heterostructure with intrinsic thin layer(HIT) silicon solar cells. Samples are patterned on an indium tin oxide(ITO) layer using polymer resist printing. After polymer resist patterning, a Ni seed layer is deposited by sputtering. A Cu electrode is electroplated in a Cu bath consisting of $Cu_2SO_4$ and $H_2SO_4$ at a current density of $10mA/cm^2$. Copper electroplating electrodes using a screen printer are successfully implemented to a line width of about $80{\mu}m$. The contact resistance of the copper electrode is $0.89m{\Omega}{\cdot}cm^2$, measured using the transmission line method(TLM), and the sheet resistance of the copper electrode and ITO are $1{\Omega}/{\square}$ and $40{\Omega}/{\square}$, respectively. In this paper, a screen printer is used to form a solar cell electrode pattern, and a copper electrode is formed by electroplating instead of using a silver electrode to fabricate an efficient solar cell electrode at low cost.

• Bulletin of the Korean Chemical Society
• /
• 제24권8호
• /
• pp.1197-1202
• /
• 2003

Patterning of biological molecules was attempted on both gold and glass using fourth generation (G4) poly(amidoamine) (PAMAM) dendrimer as an interfacing layer between solid surfaces and biomolecules. As for the patterning of avidin and anti-biotin antibody on gold, PAMAM dendrimers representing amine functionalities were firstly printed onto the 11-mercaptoundecanoic acid SAM by microcontact printing, followed by biotinylation, and reacted with fluorescence-labeled avidin or anti-biotin antibody. Fluorescence microscopic analysis revealed that the patterns of avidin and anti-biotin antibody were well constructed with the resolution of < 2 ㎛. The PAMAM dendrimers were also printed onto aldehyde-activated slide glass and reacted directly with anti-BSA antibodies, which had been oxidized with sodium periodate. As a result, distinct patterns of the anti-BSA antibodies were also obtained with a comparable edge resolution to that of avidin patterns on gold. These results clearly show that PAMAM dendrimers can be adopted as an interfacing layer for the patterning of biological molecules on solid surfaces with micrometer resolution.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.775-777
• /
• 2003

Several methods are available for the fabrication of electrode pattern for the plasma display panel(PDP) including screen printing and photolithographic method. Piezo type ink-jet printing method is considered to the method of choice for electrode patterning in manufacturing of PDP. Both silver ink and absorbent layer paste formulation were developed for ink-jet printing of electrode pattern. The ink-jet printing of silver electrode with preformed absorbent layer was especially suitable for the patterning of address electrode for high resolution PDP.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2003년도 춘계학술발표논문집
• /
• pp.239-242
• /
• 2003

Scale down으로 인해 부족해진 overlay margin을 통해 충분히 확보해주고, 이와 동시에 attPSM(attenuated phase shift)의 사용으로 발생하는 side-lobe 현상을 억제하기 위한 방법으로 rule-based OPC(optical proximity correction)룰 사용하여 side-lobe만을 효과적으로 추출한 후, 그 자리에 scattering bar를 삽입하였다. 그리고 ORC(optical rule checking)를 통해 original layout과 aerial image의 EPEs(edge placement errors)를 검사하여 검증에 걸리는 시간을 감소시켰다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.536-539
• /
• 2004

A novel ink-jet printing method was investigated for fine patterning of phosphor layer in PDP using a precision nozzle printing. A reverse emulsion method was developed for the synthesis of nano-sized phosphor powder that could be formulated in the phosphor ink. The composition of the phosphor ink including charge controlling agents, solvent, dispersant and nano-sized phosphor powder was optimized for the fine patterning of phosphor layer for high resolution PDP.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.191-191
• /
• 2007

By employing a photo-sensitive PVA as a photoresist, we first demonstrated simultaneous patterning and passivation of P3HT active layer. The passivation layers were obtained by annealing the organic layers after developing PVA and over-etching the P3HT layer. The fabricated OTFTs were electrically characterized. The OTFTs after the passivation exhibited the field-effect of ${\sim}5.9{\times}10^{-4}cm^2/V{\cdot}s$, on/off current ratio of ${\sim}10^3$. The value of OTFTs a little degradation with time in air but it appeared different unpassivated OTFT.

• 한국레이저가공학회지
• /
• 제3권2호
• /
• pp.35-43
• /
• 2000

Laser direct patterning of the coated photoresit (PMER-NSG31B) layer was studied to make halftone dots on gravure printing roll. The selective laser hardening of photoresist by Ar-ion laser(wavelength : 333.6nm∼363.8nm) was controlled by the A/O modulator. The coating thickness in the range of 5㎛∼11㎛ could be obtained by using the up-down directional moving device along the vertically located roll. The width, thickness and hardness of the hardened lines formed under laser power of 200∼260㎽ and irradiation time of 4.4∼6.6$\mu$ sec/point were investigated after developing. The hardened width increased according to the increase of coating thickness. Though the hardened thickness was changed due to the effect of the developing solution, the hardened layer showed good resistance to the scratching of 2H pencil. Also, the hardened minimum line widths of 10㎛ could be obtained. The change of line width was also found after etching, and the minimum line widths of 6㎛ could be obtained. The hardened lines showed the good resistance to the etching solution. Finally, the experimental data could be applied to make gravure halftone dots using the developed imaging process, successfully.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1997년도 한국재료학회 추계학술발표회
• /
• pp.39-39
• /
• 1997

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권1호
• /
• pp.13-17
• /
• 2006

Self-Assembled Monolayers (SAMs) formed by alkanethiol adsorption to thin metal film are widely being investigated for applications as coating layer for anti-stiction or friction reduction and in fabrication of micro structure of molecules and bio molecules. Recently, there have been many researches on micro patterning using the advantages of very thin thickness and etching resistance of Self-Assembled Monolayers in selective etching of thin metal film. In this report, we present the several machining method to form the nanoscale structure by Mask-Less laser patterning using alknanethiolate Self-Assembled Monolayers such as thin metal film etching and heterogeneous SAM structure formation.