• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.9
• /
• pp.869-874
• /
• 2011

This paper addresses the trajectory tracking problem for ship berthing by using sliding mode technique. With significant potential advantages: insensitivity to plant nonlinearities, parameter variations, remarkable stability and robust performance with environmental disturbances, the multivariable sliding modes controller is proposed for solving trajectory tracking of ship in harbor area. In this study, the ship position and heading angle are simultaneously tracked to guarantees that the ship follows a given path (geometric task) with desired velocities (dynamic task). The stability of the proposed control law is proved based on Lyapunov theory. The proposed approach has been simulated on a computer model of a supply vessel with good results.

• Advances in aircraft and spacecraft science
• /
• v.4 no.4
• /
• pp.371-399
• /
• 2017

The motion of propeller driven airplanes, flying at constant speed on ascending or descending helical trajectories is analyzed. The dynamical abilities of the airplane are shown to result in restrictions on the ranges of the geometrical parameters of the helical path. The physical quantities taken into account are the variation of air density with altitude, the airplane mass change due to fuel consumption, its load factor, its lift coefficient, and the thrust its engine can produce. Formulas are provided for determining all the airplane dynamical parameters on the trajectory. A procedure is proposed for the construction of tables from which the flyability of trajectories at a given angle of inclination and radius can be read, with the corresponding minimum and maximum speeds allowed, the final altitude reached and the amount of fuel burned. Sample calculations are shown for the Cessna 182, a Silver Fox like unmanned aerial vehicle, and the C-130 Hercules.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.613-617
• /
• 1992

The tracking control problem of a flexible manipulator with a prismatic joint along a given path is discussed. The nondimensionalization of the elastic part of the manipulator makes it possible to model such a flexible manipulator. For a discontinuous velocity trajectory, an optimal control theory has been applied to formulate the problem. The optimal scheme is given to find the input commands(e.g., joint torques) necessary to produce a, specified end effector motion. Simulated results show the potential use of this scheme for a discontinuous velocity trajectory control.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.11
• /
• pp.1831-1839
• /
• 2003

This paper deals with design and control of passive multiple trailer systems fer practical applications. Due to cost and complexity of trailer mechanism, passive systems are preferred to active systems in this research. The control objective is to minimize trajectory tracking errors of passive multiple trailers. Three types of passive trailer systems-direct-hooked, three-point, and off-hooked- are discussed in this paper. Trajectory tracking performance and stability issues under constant velocity motion are carried out for three types. Various simulations and experiments have been also performed for these three types. It is shown that the proposed off-hooked trailer system produces better tracking performance than the other types.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.584-588
• /
• 2003

In this paper, we propose a method to avoid obstacles that have unstable limit cycles in a Hyperchaos trajectory surface. We assume all obstacles in the chaos trajectory surface have a Van der Pol equation with an unstable limit cycle. When a chaos robot meets an obstacle in a hyper-chaos equation trajectory, the obstacle reflects the robot. We also show computer simulation result of hyperchaos equation trajectories with one or more Van der Pol obstacles.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2011.06a
• /
• pp.349-354
• /
• 2011

This paper addresses the trajectory tracking problem for ship berthing using sliding mode technique. With significant potential advantages: insensitivity to plant nonlinearities, parameter variations, remarkable stability and performance robustness with environmental disturbances, the multivariable sliding modes controller is proposed for solving trajectory tracking of ship in harbor area. In this study, the ship position and heading angle are simultaneously tracked to guarantees that the ship follows a given path (geometric task) with desired velocities (dynamic task). The stability of the proposed control law is proved based on Lyapunov theory. The proposed approach has been simulated on a computer model of a supply vessel with good results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.5
• /
• pp.405-411
• /
• 2011

This paper presents a hierarchical trajectory planning method which can handle a collision-free of the planned path in complex and dynamic environments. A PV (Path & Velocity profile) planning method minimizes a sharp change of orientation and waiting time to avoid a collision with moving obstacle through detour path. The path generation problem is solved by three steps. In the first step, a smooth global path is generated using $A^*$ algorithm. The second step sets up the velocity profile for the optimization problem considering the maximum velocity and acceleration. In the third step, the velocity profile for obtaining the shortest path is optimized using the fuzzy and genetic algorithm. To show the validity and effectiveness of the proposed method, realistic simulations are performed.

• The Journal of Korea Robotics Society
• /
• v.19 no.1
• /
• pp.23-30
• /
• 2024

This paper studies a GPS error filtering method that takes into account the continuity of the ongoing path to enhance the safety of autonomous agricultural mobile robots. Real-Time Kinematic Global Positioning System (RTK-GPS) is increasingly utilized for robot position evaluation in outdoor environments due to its significantly higher reliability compared to conventional GPS systems. However, in orchard environments, the robot's current position obtained from RTK-GPS information can become unstable due to unknown disturbances like orchard canopies. This problem can potentially lead to navigation errors and path deviations during the robot's movement. These issues can be resolved by filtering out GPS information that deviates from the continuity of the waypoints traversed, based on the robot's assessment of its current path. The contributions of this paper is as follows. 1) The method based on the previous waypoints of the traveled path to determine the current position and trajectory. 2) GPS filtering method based on deviations from the determined path. 3) Finally, verification of the navigation errors between the method applying the error filter and the method not applying the error filter.

• Journal of Korea Spatial Information System Society
• /
• v.10 no.3
• /
• pp.67-78
• /
• 2008

With the rapid development of wireless communication and mobile equipment, many applications for location-based services have been emerging. Moving objects such as vehicles and ships change their positions over time. Moving objects have their moving path, called the trajectory, because they move continuously. To monitor the trajectory of moving objects in a large scale database system, an efficient Indexing scheme to processed queries related to trajectories is required. In this paper, we focus on the issues of minimizing the dead space of index structures. The Minimum Bounding Boxes (MBBs) of non-leaf nodes in trajectory-preserving indexing schemes have large amounts of dead space since trajectory preservation is achieved at the sacrifice of the spatial locality of trajectories. In this thesis, we propose entry relocating techniques to reduce dead space and overlaps in non-leaf nodes. we present performance studies that compare the proposed index schemes with the TB-tree and the R*-tree under a varying set of spatio-temporal queries.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.191-198
• /
• 2006

Dieless CNC forming is an innovative technology which can form various materials with complex shape by numerically controlled incremental forming process. In this paper, a method of NC tool path generation based on an STL file for dieless CNC forming is proposed. Tool trajectory adopts the principle of layered manufacturing in rapid prototyping technology, but it is necessary to consider STL offset because of the ball shaped tool with a radius. Vertex offset method which enables to compute offset STL directly is engaged for STL offset. The offseted STL is sliced by cutting planes to generate contouring tool path. Algorithm is implemented on a computer and experimented on a dieless CNC forming machine to show its validity.