• 한국표면공학회지
• /
• 제36권6호
• /
• pp.423-429
• /
• 2003

It has been investigated corrosion resistance and crystal structure of Zn-Cr coatings fabricated by electroplating method and electron-beam physical vapor deposition method(EB-P VD). The electroplated Zn-Cr alloy consists mainly of η'-Zn phase for the lower Cr content than 7.9 wt% Cr and ${\gamma}$'-ZnCr phase for the higher Cr content. In the Zn-Cr alloy fabricated by EB-PVD the ${\gamma}$'-ZnCr phase appeared clearly at 3 wt% Cr and it became the sole phase at 50 wt%Cr. The amount of η'-Zn phase decreased obviously with increasing Cr content when it exceeded 15 wt% Cr. The electrochemical measurement of the electroplated Zn-Cr film has shown corrosion potential of about -1000 mV. The current density of active region and the amount of dissolved Zn and Cr decreased significantly with increasing Cr content. The electrochemical characteristics of Zn-Cr alloy fabricated by EB-PVD have shown that the alloy of 50 wt% Cr had the highest corrosion potential(-500 mV) and the lowest critical passive current density than that of the electroplated.

• Advances in nano research
• /
• 제10권3호
• /
• pp.211-219
• /
• 2021

The evaluation of the corrosion resistance of titanium with a TiO2 nanotubes top layer was carried out (TiO2 NT). These nanostructures were evolved into anatase nanoparticles without heat treatment in an aqueous medium, which is a novel phenomenon. This work analyzes the layer between the nanotube bottom and the substrate, which is thin and still susceptible to corrosion. The bottom of TiO2 nanotubes having Fluor resulting from the synthesis process changed between amorphous to crystalline anatase with a crystallite size of about 4 nm, which influenced the corrosion rates. Four kinds of samples were evaluated. A) NT by Ti anodizing; B) NTSB for Ti plates, either modifying its surface or anodizing the modified surface; C) NT-480 for anodized Ti and heat-treated (480℃) for reaching the anatase phase; D) NTSB-480 for Ti plates, first, modifying its surface using sandblast, after that, anodizing the modified surface, and finally, heat-treated to 480℃ to compare with samples having induced crystallization and passivation. Four electrochemical techniques were used to evaluate the corrosion rates. The surfaces having TiO2 nanotubes with a sandblast pre-treatment had the highest resistance to corrosion.

• 한국주조공학회지
• /
• 제43권5호
• /
• pp.230-240
• /
• 2023

염화물 환경에서 329LD 린 듀플렉스 스테인리스강과 CF3M 오스테나이트 스테인리스강 주물재의 공식 거동을 조사하였다. CF3M 합금에 비해 상대적으로 낮은 Ni 및 낮은 Mo 함량을 갖는 329LD 합금의 공식 전위, 부동태 영역 및 임계 공식 온도는 상용 CF3M 합금보다 높기 때문에 329LD 합금의 공식 저항성은 CF3M 합금보다 우수하였다. CF3M 합금에 비해 높은 Cr과 Mo 와 중간 정도의 N 함량을 갖는329LD 합금의 공식 저항성이 향상된 이유는 크게 두 가지이다. 첫째, 329LD 합금의 공식 저항 당량지수 (PREN δ+γ) 값이 CF3M 합금보다 높다. 둘째, 329LD 합금의 부동태 영역은 CF3M 합금의 부동태 영역보다 크다. 이는 329LD 합금에 높은 Cr과 낮은 Mo 및 중간 정도의 N 함량을 첨가함으로써 세 원소의 시너지 효과가 부동태 피막의 부동태를 향상시켜 내식성을 증가시키기 때문이다. 공식저항 당량지수에서 N factor 16을 이용하여 계산된 오스테나이트 (γ)의 PREN_γ과 페라이트 (δ) 값의 PREN_δ을 계산한 결과 오스테나이트 (γ)의 PREN_γ 값이 페라이트 (δ)보다 작으므로 329LD 합금의 공식은 γ상에서 선택적으로 시작되어 최종적으로는 γ상에서 δ상으로 전파됨을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.348-351
• /
• 2006

Bipolar plate, which forms about 50% of the stack cost, is an important core part with polymer electrolyte membrane in PEMFC. Bipolar plates have been commonly fabricated from graphite meterial having high electrical conductivity and corrosion resistance. Lately, many researchers have concentrated their efforts on the development of metallic bipolar plate and stainless steel has been considered as a potential material for metallic bipolar plate because of its high strength, chemical stability, low gas permeability and applicability to mass production. However, it has been reported that its inadequate corrosion behavior under PEMFC environment lead to a deterioration of membrane by dissolved metal ions and an increase in contact resistance by the growth of passive film therefore, its corrosion resistance as well as contact resistance must be improved for bipolar plate application. In this work, several types of coating were applied to 316L and their electrical conductivity and corrosion resistance were evaluated In the simulated PEMFC environment. Application of coating gave rise to low interfacial contact resistances below $19m{\Omega}cm^2$ under the compress force of $150N/cm^2$. It also made the corrosion potential to shift in the posit ive direct ion by 0.3V or above and decreased the corrosion current from ca. $9{\mu}A/cm^2$ to ca. $0.5{\mu}A/cm^2$ in the mixed solution of $0.1N\;N_2SO_4$ and 2ppm HF A coat ing layer under potentiostatic control of 0.6V and $0.75V_{SCE}$ for 500 hours or longer showed some instabilities, however, no significant change in coat Ing layer were observed from Impedance data. In addition, the corrosion current maintained less than $1{\mu}A/cm^2$ for most of time for potentiostatic tests. It indicates that high electrical conductivity and corrosion resistance can be obtained by application of coatings in the present work.

• 대한화학회지
• /
• 제56권4호
• /
• pp.448-458
• /
• 2012

In order to develop alloy resistance in aggressive sulphat ion, the corrosion behavior of metallic glasses $Ni_{92{\cdot}3}Si_{4.5}B_{32}$, $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ (at %) at different concentrations of $H_2SO_4$ solutions was examined by electrochemical methods and Scanning Electron Microscope (SEM) and X-ray Photoelectron Microscopy (XPS) analyses. The corrosion kinetics and passivation behavior was studied. A direct proportion was observed between the corrosion rate and acid concentration in the case of $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ alloys. Critical concentration was observed in the case of $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ alloy. The influence of the alloying element is reflected in the increasing resistance of the protective film. XPS analysis confirms that the protection film on the $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ alloy was NiS which is less protective than that formed on Cr containing alloys. The corrosion rate of $Ni_{82,3}Cr_7Fe_3Si_{4.5}B_{3.2}$ and $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$. alloys containing 7% and 13% Cr are $7.90-26.1{\times}10^{-3}$ mm/y which is lower about 43-54 times of the alloy $Ni_{92{\cdot}3}Si_{4.5}B_{32}$ (free of Cr). The high resistance of $Ni_{75.5}Cr_{13}Fe_{4.2}Si_{4.5}B_{2.8}$ alloy at the very aggressive media may due to thicker passive film of $Cr_2O_3$ which hydrated to hydrated chromium oxyhydroxide.

• 한국표면공학회지
• /
• 제53권2호
• /
• pp.43-52
• /
• 2020

Various aging treatments were conducted on AISI 630 martensitic precipitation hardening stainless steel in order to optimize aging condition. Aging treatment was carried out in the vacuum chamber of Ar gas with changing aging temperature from 380℃ to 430℃ and aging time from 2h to 8h at 400℃. After obtaining the optimized aging condition, several nitrocarburizing treatments were done without and with the aging treatment. Nitrocarburizing was performed on the samples with a gas mixture of H₂, N₂ and CH₄ for 15 h at vacuum pressure of 4.0 Torr and discharge voltage of 400V. The corrosion resistance was improved noticeably by combined process of aging and nitrocarburizing treatment, which is attributed to higher chromium and nitrogen content in the passive layer, as confirmed by XPS analysis. The optimized condition is finalized as, 4h aging at 400℃ and then subsequent nitrocarburizing at 400℃ with 25% nitrogen and 4% methane gas for 15h at vacuum pressure of 4.0 Torr and discharge voltage of 400V, resulting in the surface hardness of around 1300 HV_0.05 and α'_N layer thickness of around 11 ㎛ respectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.381-384
• /
• 2008

본 연구에서는 폭렬방지용 합성섬유의 효과적인 투입방안 마련을 목적으로, 섬유혼입 프리믹스시멘트 결합재를 사용한 고강도 콘크리트의 폭렬방지 및 내화특성을 검토하였다. 내화시험 결과, 원주형 공시체의 폭렬은 W/C 15%의 수동투입에서 일부 박리 또는 파괴폭렬이 발생한 것을 제외하고 대부분 방지되었고, 전체적으로 섬유혼입 프리믹스시멘트는 폭렬방지 성능이 섬유 수동투입과 비교하여 동등 이상으로 우수하였으며, 결합재량이 많아 점성이 큰 고강도 콘크리트일수록 양호한 섬유의 분산성으로 폭렬방지에 더욱 효과적인 것으로 나타났다. 또한, 섬유혼입 프리믹스시멘트 결합재를 사용한 기둥부재의 온도이력은 폭렬이 방지되어 철근이 노출되지 않으면 최외곽 철근의 온도가 내화성능기준의 평균온도 538$^{\circ}C$를 넘지 않는 것으로 나타나, 고강도 콘크리트의 내화기준을 만족하였다.

• Corrosion Science and Technology
• /
• 제22권5호
• /
• pp.359-367
• /
• 2023

The localized corrosion resistance of the Ni-based Inconel 718 alloy after solution heat treatment was evaluated using electrochemical techniques in a solution of 25 wt% NaCl and 0.5 wt% acetic acid. Solution heat treatment at 1050 ℃ for 2.5 hours resulted in an increased average grain diameter. Both Ti carbides (10 ㎛ diameter) and Nb-Mo carbides (1 - 9 ㎛ diameter) were distributed throughout the material. Despite heat treatment, the shape and composition of these carbides remained consistent. An increase in solution temperature led to a decrease in pitting potential value. However, the pitting potential value of solution heat-treated Inconel 718 was consistently higher than that of as-received Inconel 718 at all tested temperatures. Localized corrosion initiation occurred at 0.4 V_SSE in a temperature environment of 80 ℃ for both as-received and solution heat-treated Inconel 718 alloys. X-ray photoelectron spectroscopic analysis indicated that the composition of the passive film formed on specimen surfaces remained largely unchanged after solution heat treatment, with O1s, Cr2p_3/2, Fe2p_3/2, and Ni2p_3/2 present. The difference in localized corrosion resistance between as-received and solution heat-treated Inconel 718 alloys was attributable to microstructural changes induced by the heat treatment process.

• 대한전자공학회논문지
• /
• 제11권4호
• /
• pp.19-24
• /
• 1974

LC ladder형의 여파회로등에 필요한 비접지 inductance를 유도소자없이 구성하기 위하여 2개의 연산증폭기와 수동소자를 쓰는 방식을 제시하였다. Indefinite admittance matrix를 써서 이 회로강이 가등적으로 병렬로 정과 부의 저항과 직렬로 순 inductance가 있는 π형회로임을 증명하였고, 실제로 low-pass 여파회로의 구성에 응용하여 얻어진 주파수특성이 만족할만함을 보였다. 이 방법에 의한 비접지 inductance는 지금까지 발표된 방법과 비교할 때 실현된 inductance에 직렬저항성분이 없음으로 Q가 높아서 유리하다. 또한 소요된 연산증폭기의 수도 적다.

• 전력전자학회논문지
• /
• 제21권5호
• /
• pp.404-410
• /
• 2016

To avoid the stability issues of LLCL filters, passive or active damping methods to eliminate the resonance phenomena are required. In this paper, system stability of a current control is analyzed when the active damping scheme based on the virtual resister is utilized in single-phase grid converter systems with LLCL input filters. The control performance according to the parameters of the virtual resistance is investigated. The validity of stability analysis was verified by simulation and experimental results.