• The Journal of Advanced Prosthodontics
• /
• v.12 no.5
• /
• pp.291-298
• /
• 2020

PURPOSE. The aim of this study is to evaluate the influence of repeated surface treatments on wettability and surface roughness for zirconia surface and bond strength of zirconia-based ceramics to resin cement. MATERIALS AND METHODS. Seventy blocks (10 × 10 × 3 mm) of zirconia-based ceramics were fabricated and divided into two groups according to the surface treatments: (A) 110 ㎛ Al₂O₃ airborne-particle abrasion and (R) 110 ㎛ silica modified Al₂O₃ airborne-particle abrasion. At stage 2, each group was subdivided into 5 groups according to the surface retreatments: (a) 110 ㎛ Al₂O₃ airborne-particle abrasion, (r) 110 ㎛ silica modified Al₂O₃ airborne-particle abrasion, (D) diamond bur, (Da) diamond bur + 110 ㎛ Al₂O₃ airborne-particle abrasion, and (Dr) diamond bur + 110 ㎛ silica modified Al₂O₃ airborne-particle abrasion. Cylinders of self-adhesive resin cement were cemented onto each treated ceramic surface and subjected to micro-shear bond strength test. Additional specimens were prepared for roughness and wettability analyses. The data were subjected to t-test and One-way ANOVA followed by Tukey's post hoc test (α=.05). RESULTS. At stage 1, group R presented higher bond strength values than group A (P=.000). There was a statistically significant increase of bond strength at stage 2 for group A (P=.003). The diamond bur influenced the surface roughness, increasing the values (P=.023). Group R provided better wettability. Regardless of the applied surface treatment, most of failures were adhesive. CONCLUSION. The combination of application and reapplication of Rocatec Plus showed the best results of bond strength. Surface retreatment and recementation might be an indicated clinical strategy.

• Food Science of Animal Resources
• /
• v.34 no.6
• /
• pp.852-857
• /
• 2014

This study was carried out to develop a simple, convenient, and reproducible testing device to determine wettability and dispersibility of dairy powders. The testing device consists of a sieve ($150{\mu}m$) attached to a sample chamber, sensors mounted on a supporting body and a main control unit containing a display panel. The sensors detect the difference in electrical resistance between air and water. A timer is automatically triggered by the sensor when the bottom of sample-loaded chamber contacts water in the petri dish. Wettability and dispersibility of commercial skim milk powders (SMPs) produced at different heating strengths (low-, medium-, and high-heat SMP) are compared using the new testing device. Wettability of the SMPs were correlated with particle size and are found to increase in the order of medium-, low-, and high-heat SMP regardless of the amount of sample tested. Dispersibility of SMPs showed the same trend and high heat-SMP which has the smallest particle size resulted in the lowest dispersibility. Unlike existing methods, the new testing device can determine both wettability and dispersibility of powders and successfully detected differences among the samples.

• Interaction and multiscale mechanics
• /
• v.5 no.4
• /
• pp.399-405
• /
• 2012

A dissipative particle dynamics (DPD) simulation was presented to analyze surface wettability and contact angles of a droplet on a solid platform. The many-body DPD, capable of modeling vapor-liquid coexistence, was used to resolve the vapor-liquid interface of a droplet. We found a constant density inside a droplet with a transition along the droplet boundary where the density decreased rapidly. The contact angle of a droplet was extracted from the isosurfaces of the density generated by the marching cube and a spline interpolation of 2D cutting planes of the isosurfaces. A wide range of contact angles from $55^{\circ}$ to $165^{\circ}$ predicted by the normalized parameter ($|A_{SL}|/B_{SL}$) were reported. Droplet with the parameters $|A_{SL}|>5.84B{_{SL}}^{0.297}$ was found to be hydrophilic. If $|A_{SL}|$ was much smaller than $5.84B{_{SL}}^{0.297}$, the droplet was found to be superhydrophobic.

• Elastomers and Composites
• /
• v.41 no.3
• /
• pp.157-163
• /
• 2006

In this study, the wettability and mechanical properties of silicone rubber impression material were studied by using precipitated silica and fumed silica with different particle size and polarity (hydrophilic/hydrophobic). Curing time of impression material depended on the particle size of fumed silica. The curing time delayed about 9 minutes by using A300, which was the fumed silica with the smallest particle size among the silica used in this study. Wettability of rubber impression material improved with the introduction oi hydrophobic fumed silica(R972). Also, the optimum flow and mechanical properties could be obtained by using blended silica with the 90: 10 ratio of precipitated and fumed silica.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.175-177
• /
• 2006

Electrically Conductive Adhesives(ECAs) with solderable particles have been developed as an alternative to Pb-free solders. Our previous study proved that good wettability of solder particle is a prerequisite for the establishment of conduction paths. In this paper, two types of ECAs were formulated and the wetting characteristic low-melting-point Sn-In solder on Cu and Ni/Au pads was investigated. It was found that Sn-In solder in the developed resin material with reduction capability shows good wettability, especially on Cu pad.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.4
• /
• pp.93-100
• /
• 2022

This study describes the evaluation results on the effect of soil particle surfaces coated with various hydrophobic conditions on spectral information according to water content. Wettability test and spectral information evaluation test were performed on the hydrophobic coated standard sand. When the standard sand was coated with 1%, 3%, and 5% hydrophobic, the contact angles of sand-water interface were 130°~143°, 129°~144°, and 131°~144°, respectively. This means that the contact angle increased as the degree of hydrophobic coating increased at the same drying time, but the range of the contact angle had the same wettability. This means that the contact angle increases as the hydrophobic coating degree increases at the same drying time, whereas the contact angle range has the same wettability. As a result of spectral information evaluation, the maximum spectral reflectance of the dried sand with hydrophobic condition decreased compared to that of the hydrophilic sand, as the degree of hydrophobic increased. However, the maximum spectral reflectance was increased by increasing the degree of hydrophobic under the same water content conditions.

• Food Science of Animal Resources
• /
• v.42 no.6
• /
• pp.915-927
• /
• 2022

Recently, protein-fortified milk powders are being widely consumed in Korea to prevent sarcopenia, and the demand for high-protein food powders is continuously increasing in the Korean market. However, spray-dried milk proteins have poor flowability and wettability owing to their fine particle sizes and high inter-particle cohesive forces. Fluidized bed agglomeration is widely used to improve the instant properties of food powders. This study investigated the effect of fluidized bed agglomeration on whey protein isolate (WPI)-fortified skim milk powder (SMP) at different SMP/WPI ratios. The fluidized bed process increased the particle size distribution, and agglomerated particles with grape-like structures were observed in the SEM images. As the size increased, the Carr index (CI) and Hausner ratio (HR) values of the agglomerated WPI-fortified SMP particles exhibited excellent flowability (CI: <15) and low cohesiveness (HR: <1.2). In addition, agglomerated WPI-fortified SMP particles exhibited the faster wetting time than the instant criterion (<20 s). As a result, the rheological and physical properties of the WPI-fortified SMP particles were effectively improved by fluidized bed agglomeration. However, the fluidized bed agglomeration process led to a slight change in the color properties. The CIE L^* decreased, and the CIE b^* increased because of the Maillard reaction. The apparent viscosity (η_a,10) and consistency index (K) values of the rehydrated solutions (60 g/180 mL water) increased with the increasing WPI ratio. These results may be useful for formulating protein-fortified milk powder with better instant properties.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.457-462
• /
• 2010

In this research, the effects of the concrete superplastizers on the wettability of cement particle and concrete strength were studied. The wettability of the cement particles strongly depended on the type of the superplastizer. When the superplastizer had a higher wettability with the cement particles, it revealed a good fluidity of the concrete mortar and a higher concrete strength. Non-ionic superplastizers (polycarboxylic type) had a relatively good performance on the mortar fluidity and concrete strength properties compared to anionic superplastizers (lignosulfate, sulfonated naphthalene formaldehyde, sulfonated melamin formaldehyde). It was observed that the blending of the polycarboxylic and the lignosulfate type concrete superplastizers resulted in synergistic effects on the concrete mortar fluidity and concrete strength properties.

• Environmental Engineering Research
• /
• v.21 no.2
• /
• pp.121-131
• /
• 2016

In most African urban areas, Particulate Matters (PM) concentration exceeds by far the WHO limits. In these areas, plants can play a key role in removing particles. In this study, we evaluated three ornamental species (Jatropha interrigima, Ficus benjamina, Barleria prionitis) used in Abidjan (Ivory Coast). Leaf-encapsulated saturation isothermal remnant magnetisation (SIRM) were measured and the relationship between PM captured and leaf wettability were done. The sampling were performed at roadsides and Parks. Firstly, Leaf-encapsulated and total leaf SIRM were quantified and the wettability was determined by drop contact angles (DCA). Secondly, the relationship between leaf SIRM and wettability was found. Results showed that leaf SIRM was two to ten times higher at roadsides than in Parks. Total leaf SIRM was also higher on mature leaves in Main roads suggesting a particle accumulation in leaves over time especially in waxy species (Ficus benjamina). This species encapsulated other than 20% of total leaf SIRM. All tested species were highly-wettable ($40^{\circ}$ < DCA < $90^{\circ}$). Thus, Jatropha interrigima with its leaf trichomes and F. benjamina with its leaf waxes were more wettable. A significantly positive correlation was found between wettability intensity and leaf SIRM.

• Korean Journal of Metals and Materials
• /
• v.46 no.5
• /
• pp.289-295
• /
• 2008

The effect of the alloy elements(Si/Mn) ratio on the coating quality including wettabilty with molten zinc, galvannealing kinetics and crater has been investigated in interstitial-free high strength steel(IFHSS) containing Si and Mn. When the Si/Mn ratio was below 0.75, IF-HSS exhibited a good wettability leading to a good galvannealed coating quality after annealing at $800^{\circ}C$ for 40s in $15%H_2-N_2$ mixed gas with dew point $-60^{\circ}C$. In contrast, the wettability and galvannealed coating quality were deteriorated in the Si/ Mn ratio above 0.75. It is shown that they have relevance to oxides forms by selective oxidation on the steel surface. The oxide particles dispersed on the steel surface with a surface coverage of below 40% resulted in good wettability and galvannealed coating quality. The oxide particle is mainly consisted of $Mn_2SiO_4$ with low contact angle in molten zinc. On the other hand, the continuous oxide layer on the steel surface, such as network- and film-type,caused to poor wettability and galvannealed coating quality. The coverage of oxide layer was above 80%, and its chemical species was $SiO_2$ with high contact angle in molten zinc. Consequently, the Si/Mn alloy ratio played an importance role in galvannealed coating quality of IF-HSS.