• Asian-Australasian Journal of Animal Sciences
• /
• 제11권5호
• /
• pp.597-607
• /
• 1998

Processing is generally employed to alter the physical and chemical properties of feeds used in pig diets, using hammer/roller mills, pellet mills and extruders/expanders. The reported optimum particle sizes of corn are approximately $500{\mu}m$, $500-700{\mu}m$, $400-600{\mu}m$, for nursery, growing-finishing, and breeder pigs respectively. Optimum particle size of grains are affected by diet complexity. There was a trend towards reducing particle size in order to increase ADG in pigs fed a simple diet, though such was not the case for pigs fed a complex diet. Uniformity of particle size also affects the nutritional values of swine feeds. Uniform particle sizes would consistently give greater nutrient digestibilities. In terms of pellet quality, it is reported that a higher incidence of fmes in pelleted feeds has a direct correlation with poorer feed conversion ratio in pigs. Particle and pellet sizes are also very important for pelleting in terms of grinding, digestibility, stomach ulceration and pellet durability. A particle size of $600{\mu}m$, or slightly less, seemed optimal for com in fmishing pigs, and the 5/32 in. diameter pellets supported the best efficiencies of gain during nursery and finishing phases. Extruder and/or expander processes would allow the feed industry an increased flexibility to utilize a wider spectrum of feed ingredients, and improve pellet quality of finished feeds. It would appear that extruded or expanded diets containing highly digestible ingredients have little effect on the growth performance of pigs, and the feeding values of the feeds over pelleted diets were not improved as pigs grew. The extruder or expander is much more effective than a pelletizer in salmonella control. Gastric ulcerations and/or keratinizations were consistently reported in pigs fed mash and processed diets containing finely ground grains, whereas carcass quality was not affected by diet processing methods such as pelleting, extruding or expanding. In corn- or sorghum-based diets, the electrical energy consumption is 4-5 times higher in the expanding than in the pelleting process. But the expander's processing cost was half of that shown by an extruder. Finally, the decision of which feed processing technology to adopt would depend on the processing cost, and any potential improvement in growth performance and digestibilities of nutrients should offset the increased operating and capital costs related to the extruder/expander technology over mash or pelleting processes in pigs.

• Journal of Conservation Science
• /
• 제38권2호
• /
• pp.80-86
• /
• 2022

Termites cause massive damage to wooden architectural heritage structures. Chemical treatments have been commonly used to control them. In foreign countries, physical barriers made of sheet and particles impenetrable to termite are being used as an alternative to the chemical method. To study the efficacy of physical barriers, we investigated the appropriate sand particle size that can prevent the penetration of R. speratus kyushuensis. Upon evaluating the barrier properties of sand with particle sizes ranging from 0.85 to 4.00 mm, the penetration of termites was found to be effectively blocked at a particle size range of 1.00 to 2.80 mm. At smaller particle sizes, termites managed to move the sand particles and build an almost linear mud tube to penetrate the sand layer. At larger particle sizes, the termites could penetrate the sand layer by passing through the sand gaps.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2002년도 제18회 학술발표대회 논문초록집
• /
• pp.64-64
• /
• 2002

Two dimensional velocity distributions outside a Mach 2.0 supersonic nozzle have been investigated using digital particle image velocimetry (PIV). Mean velocities, turbulence intensities, vorticity field and volume dilatation field are obtained from 300 instantaneous PIV images using 0.33 $\mu\textrm{m}$ $TiO_2$ particle. The seeding particle of larger size, 1.4 $\mu\textrm{m}$ $TiO_2$, is also used for the experimental measurements of velocity lag downstream of shock waves according to particle sizes. The results have been compared and analyzed with schlieren photographs and computational fluid dynamics (CFD) results for the velocity distribution, the locations of shock waves and over-expanded shock structure. It was shown that the locations of normal shock and shock waves can be resolved by the axial or radial velocities, and the velocity lag is more significantly increased due to particle inertia as a particle size increases. And it was also found that over-expanded shock structures call be predicted by volume dilatation fields, and streamwise turbulence intensities are influenced significantly by normal shock waves.

• Journal of the Korean Ceramic Society
• /
• 제37권6호
• /
• pp.545-551
• /
• 2000

Sintering behaviors of the glass-alumina composites for low firing temperature were investigated as a function of the particle size of glass frit. The system of glass frit was Pb-B-Si-Al-O. The median particle sizes of the glass frits were 2.72$\mu\textrm{m}$, 2.67$\mu\textrm{m}$ and 1.33$\mu\textrm{m}$, which were prepared with changing ball-milling times as 24 h, 48 h and 96 h. The glass-alumina composites showed maximum density at certain temperature, and further heating led to dedensification behaviors, so called over-firing. The sintering temperature, which showed maximum density, raised from 425$^{\circ}C$ to 475$^{\circ}C$ with increase of particle size of glass frit from 1.33$\mu\textrm{m}$ to 2.72$\mu\textrm{m}$. Especially, the over firing behaviors, which were occurred at high sintering temperatures, were greatly increased with decrease of particle size of glass frit.

• Particle and aerosol research
• /
• 제8권1호
• /
• pp.29-35
• /
• 2012

The Faraday cup electrode of different size has been developed and evaluated to investigate the diffusion effect of particles by Brownian motion in a particle beam mass spectrometer(PBMS). Particles which focused and accelerated by aerodynamic lens are charged to saturation in an electron beam, and then deflected electrostatically into a Faraday cup detector for measurement of the particle current. The concentration of particles is converted from currents detected by Faraday cup. Measurements of particle current as a function of deflection voltage are combined with measured relationships between particle velocity and diameter, charge and diameter, and mass and diameter, to determine the particle size distribution. The particle currents were measured using 5, 10, 20, 40 mm sized Faraday cup that can be move to one direction by motion shaft. The current difference for each sizes as a function of position was compared to figure out diffusion effect during transport. Polystyrene latex(PSL) 100, 200 nm sized standard particles were used for evaluation. The measurement using 5 mm sized Faraday cup has the highest resolution in a diffusion distance and the smaller particles had widely diffused.

• Journal of the Korean Ceramic Society
• /
• 제39권10호
• /
• pp.919-927
• /
• 2002

In order to fabricate double-layered porous materials powders of different particle sizes were pressed stepwise. Ford＇s equation which predicts the fired density with the change in pressed density was employed in order to adjust the difference in sintering shrinkage of the green body with double-layered porous structure. Double-layered porous materials were characterized by investigating microstructures and permeability. SEM micrographs showed the distinct difference in pore sizes of double-layered porous material. Permeability of single-layered porous material increased by increasing the starting particle sizes and porosity as well. Permeability of the double-layered porous material depends largely on the layer of small pore diameter.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제18권4호
• /
• pp.1039-1049
• /
• 1994

The intermitternt and transient fuel spray have been investigated from the simultaneous measurement of droplet sizes and velocities by using Phase/Doppler Particle Analyzer(PDPA). Measurement have been done on the spray axis and at the edge of the spray near nozzle at various gas-to-liquid density ratios(.rho./sub g//.rho./sub l/) that ranges from those found in free atmospheric jets to conditions typical of diesel engines. Probability density distributions of the droplet size and velocity were obtained from raw data and mathematical probability density functions which can fit the experimental distribations were extracted using the principle of maximum likelihood. In the near nozzle region on the spray axis, droplet sizes ranged from the lower limit of the measurement system to the order of nozzle diameter for all (.rho./sub g/ /.rho./sub l/) and droplet sizes tended to be small on the spray edge. At the edge of spray, average droplet velocity peaked during needle opening and needle closing. The rms intensity is greatly incresed as the radial distance from the nozzle is increased. The probability density function which can best fit the physical breakage process such as breakup of fuel drops is exponecially decreasing log-hypebolic function with 4 parameters.

• Food Science and Biotechnology
• /
• 제18권5호
• /
• pp.1161-1172
• /
• 2009

Food nanoemulsion systems consisting of water and oleoresin capsicum (OC), polyoxythylene sorbitan esters (Tween 20, 40, 60, and 80), propylene glycol (PG), sucrose monostearate (SM), and their corresponding mixtures were formulated to use as food vehicles. Tween 80 produced OC nanoemulsions with stable dispersions as one-phase systems, and the dertermined emulsification efficiencies clearly distinguished the ability of the various surfactants to emulsify OC. The nanoemulsions were prepared by both ultrasonication and self-assembly, and the nanoemulsion areas were determined using phase diagrams by measuring the sizes of the emulsions. One-phase nanoemulsions were presented, with a multiple cloudy region and phase separation that were dependent on the particle size of the emulsion. The OC nanoemulsions prepared by ultrasonication using systems of OC/Tween 80/water, OC/Tween 80/water+PG, and OC/Tween 80/water+SM, resulted in particle sizes ranging from 15 to 100 nm. Finally, the nanoemulsions maintained their initial sizes during storage, ranging from 65 to 92 nm.

• International Journal of Safety
• /
• 제4권1호
• /
• pp.18-22
• /
• 2005

A model was proposed for investigating the particle removal from suspension with particles of different sizes by deep-bed filtration, and the collection efficiency was predicted by computer simulation. Deposited particles on the pore surface may act as additional collector and reduce the pore size, which contribute to the improved collection efficiency with increase of deposition. Computer experiments for suspension of particles of three sizes and its equivalent size of mono particles were carried out and compared. The collection efficiency of suspension with poly-dispersed particles shows higher efficiency than that of suspension with mono-dispersed particles. Also the collection efficiency of smell particle of mixture is higher that that of same uniform size particles.

• Korean Journal of Food Science and Technology
• /
• 제26권2호
• /
• pp.184-187
• /
• 1994

Size distributions of rice flour measured by microscope, sieve, Coulter counter (electrozone) and aerodynamic (Aerosizer) methods were compared. Among the particle sizes measured by four methods, those by microscope and sieve were the smallest and the largest, respectively. Difference was found between the particle sizes measured by Coulter counter and aerodynamic methods.