• Journal of the Korean GEO-environmental Society
• /
• v.15 no.6
• /
• pp.17-29
• /
• 2014

A remedial investigation was conducted at five military training ranges in northern Gyeonggi province to collect information necessary for the design of on-site treatment facilities for the abatement of explosive compounds release to the environment. These information includes (i) identification of dominant explosive compounds in each range, (ii) discharge/migration routes, and (iii) contaminant distribution in particle size fraction and settling velocity of the soils. The results of investigation showed that TNT and RDX are the major contaminants but the extent of contamination varied depending on the types of military training practices and topography of the site. RDX was also detected in the subsurface soil and in the nearby stream within the training ranges, suggesting release of contaminants to streams. The median concentrations of explosives in the surface soil were less than 20 mg/kg despite several 'hot spots' in which explosives concentrations often exceeds several hundred mg/kg. The average clay contents in the soil of target area was less than 5 % compared to 12 % in the control, indicating loss of smaller particles by surface runoff during rainfall due to lack of vegetative land cover. Analysis of explosive compounds and particle size distribution showed that the amount of explosive compounds in soil particles smaller than 0.075 mm was less than 10 % of the total. Settling column tests also revealed that the quantity of explosive compounds in the liquid phase of the effluent was greater than that in the solid phase. Therefore, pre-treatment of particulate matter in surface runoff of shooting range with a simple settling basin and subsequent effluent treatment with planted constructed wetlands as polishing stage for explosives in the aqueous phase would provide the shooting ranges with a self-standing, sustainable, green solution.

• Economic and Environmental Geology
• /
• v.44 no.3
• /
• pp.203-215
• /
• 2011

Geochemical and mineralogical properties of a contamited soil should be taken into account to decide a remediation strategy for a given contaminant because development and optimization of soil remedial technologies are based on geochemical and mineralogical separation techniques. The objective of this study was to investigate the geochemical and mineralogical characteristics of arsenic-contaminated soils. The arsenic-contaminated soil samples were obtained from Chonam gold mine, Gwangyang, Chonnam, Particle size analysis, sequential extraction, and mineralogical analyses were used to characterize geochemical and mineralogical characteristics of the As-contaminated soils. Particle size analyses of the As-contaminated soils showed the soils contained 17-36% sand, 25-54% silt, 9-28% clay and the soil texture were sandy loam, loam, and silt loam. The soil pH ranged from 4.5 to 6.6. The amount of arsenic concentrations from the sequential soil leaching is mainly associated with iron oxides (1 to 75%) and residuals (12 to 91%). Major minerals of sand and silt fractions in the soils were feldspar, kaolinite, mica, and quartz and minor mineral of which is an iron oxide. Major minerals of clay fraction were composed of illite, kaolinite, quartz, and vermiculite. And minor minerals are iron oxide and rutile. The geochemical and mineralogical analyses indicated the arsenic is adsorbed or coprecipitated with iron oxides or phyllosilicate minerals. The results may provide understanding of geochemical and mineralogical characteristics for the site remediation of arsenic-contaminated soils.

• Journal of Environmental Analysis, Health and Toxicology
• /
• v.21 no.4
• /
• pp.281-291
• /
• 2018

Recently, long-range atmospheric transport (LRAT) from China is regarded as a major reason for elevated levels of particulate matter (PM) in Korea. However, local emissions also play an important role in PM pollution, especially in large-scale industrial cities. In this study, PM samples were collected at suburban, residential, and industrial sites in Ulsan, Korea. Polycyclic aromatic hydrocarbons (PAHs) and heavy metals were analyzed, and a potential human health risk assessment was conducted. The concentrations of PAHs and heavy metals in total suspended particles (TSP) increased during high $PM_{10}$ episodes, and backward trajectory analysis verified the influence of LRAT from China during the high episodes. Furthermore, the concentrations of PAHs and heavy metals in $PM_{2.5}$ and $PM_{10}$ at the industrial site were higher than those at the residential site. The risk assessment of PAHs and heavy metals in $PM_{2.5}$ suggested no significant health effects. The highest levels of PAHs were measured in the particle size of $0.32{\sim}0.56{\mu}m$ at the residential site, and those of heavy metals were detected in the particle size of 1.8~5.6 and $>18{\mu}m$, reflecting different major emissions sources for both groups. On the basis of this preliminary study, we are planning long-term monitoring and modeling studies to quantitatively evaluate the influence of industrial activities on the PM pollution in Ulsan.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.4
• /
• pp.72-77
• /
• 2007

Soil contamination by heavy metals was environmental concern due to its effect on human. In this study, monopotassium phosphate $(KH_2PO_4)$ used as phosphate source to remediate the contaminated soil with heavy metals and factors such as reaction time, initial concentration and pH of phosphate solution, species of heavy metal (lead, cadmium, zinc) and particle size were controlled. Heavy metals were removed in the order Pb > Zn > Cd and the maximum effectiveness was achieved for Pb. The removal efficiency of lead was from 95% to 100% and occurred rapidly occurred during 10 minutes. Mechanism of lead immobilization is dissolution of phosphate and the forming of a new mineral with phosphate having extremely low solubility.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.2
• /
• pp.70-75
• /
• 2008

This study was carried out to evaluate the applicability of the full scale soil washing processes for reducing heavy metal contamination level of soil around an abandoned mine. In the results of soil washing of the target soil with $H_2SO_4$ and NaOH, the As concentrations of treated soil continuously increased compared with contaminated raw soil. Also, removal efficiencies of Zn and Ni were low. This problems might be caused by chemical partitioning of As in soil and its geologic origination, soil particle size, and scale up of washing plant.

• Journal of Environmental Science International
• /
• v.15 no.2
• /
• pp.121-131
• /
• 2006

Atmospheric bulk (wet and dry) samples were monthly collected in Masan and Heangam areas of Korea, to assess the deposition flux and seasonal variation of polycyclic aromatic hydrocarbons (PAHs). Deposition fluxes of PAHs in bulk samples were determined using gas chromatography coupled to mass spectrometer detector (GC/MSD). Particle deposition fluxes from Masan and Haengam areas varied from 13 to $87\;g/m^2/year$ and from 5 to $52\;g/m^2/year$, respectively. PAHs deposition fluxes in atmospheric bulk samples in Masan and Haengam areas ranged from 135 to $464\;{\mu}g/m^2/year$ and from 62.2 to $194\;{\mu}g/m^2/year$, respectively. Atmospheric deposition fluxes of particles and PAHs in this study were comparable to or slightly lower values than those from different locations in Korea and other countries. PAHs profiles of atmospheric deposition bulk samples showed slightly different from two sampling areas, however the predominant species of PAHs were similar. Indeno (1,2,3-c,d)pyrene, benzo(g,h,i)perylene, phenanthrene compounds were the most detected PAHs in deposition bulk samples. Carcinogenic PAHs occupied the contribution of approximately $30-40\%$ of the total PAHs deposition fluxes. The non-metric multi-dimensional scaling (MDS) was used, to assess the differentiation of PAHs source between two sampling areas. The result suggests that PAHs contamination sources were different according to the location and season surveyed. There was no an apparent relationship between the PAHs deposition flux against temperature and rainfall amount, even though summer season with the highest temperature and the largest amount of precipitation showed the lowest PAHs deposition flux. Benzo(e)pyrene/benzo(a)pyrene ratio indicated that the photo-degradation process was one of important factors to the seasonal variation of PAHs with the lower deposition fluxes.

• Journal of Environmental Science International
• /
• v.13 no.5
• /
• pp.469-478
• /
• 2004

Atmospheric bulk (wet and dry) samples were monthly collected in an urban environment (Daeyeon-dong) of Busan over a year, to assess the deposition flux and seasonality of dioxin-like polychlorinated biphenyls (DLPCBs) using stainless steel pots. Deposition fluxes of DLPCBs in bulk samples were determined using high resolution gas chromatography coupled to high resolution mass spectrometry (HRGC/HRMS). Particle deposition fluxes in the urban environment varied from 23 to 98 $mg^2$/year (mean 41 $gm^2$/year). DLPCB deposition fluxes in atmospheric bulk samples ranged from 0.09 to 0.77 ng-$TEQ/m^2$/year (mean 0.35 ng-$TEQ/m^2$/year). Seasonal atmospheric deposition fluxes of DLPCBs were high in winter and low in summer. Atmospheric deposition fluxes of particles and DLPCBs in this study were comparable to or slightly lower values than those of different locations in the world. Monthly DLPCB profiles in deposition bulk samples were similar over a year. Non-ortho PCBs were higher contributions to the total DLPCBs fluxes than mono-ortho PCBs. In particular, PCB 126 had the highest concentrartion (>75%) in all deposition samples, followed by PCB 169 and PCB 156. A highly positive correlation was found among the deposition fluxes of DLPCB species, suggesting the possibility of that the DLPCB contamination originated from one source. The deposition fluxes of DLPCBs were not significantly correlated with temperature and the amount of precipitation even though the summer season with the highest temperature and the largest amount of precipitation showed the lowest DLPCB deposition flux.

• Membrane Journal
• /
• v.24 no.2
• /
• pp.167-175
• /
• 2014

For selectively permeable membrane based on cellulose acetate butyrate (CAB) and polyethyleneimine (PEI) with water vapor transportability and DMMP protective performance, we intended to improve protective performance of the membrane against CEES using several additives. Results showed that CAB/PEI membranes possessed performance with good water vapor permeation (${\geq}1,800g/m^2/day$) and enhanced protective capability against CEES contamination ($7.1{\sim}11.5{\mu}g/cm^2{\cdot}day$). Of these membranes, the membrane containing $Ag^+$ ion and ionic exchange resin showed the best protective performance. And, we identified that the CAB/PEI membranes show excellent protection against aerosols with various particle sizes ($0.005{\sim}3{\mu}m$) simulating biological agents.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.23-23
• /
• 2011

Chemical-Mechanical Planarization (CMP) 공정이란 화학적 반응 및 기계적인 힘이 복합적으로 작용하여 표면을 평탄화하는 공정이다. 이러한 CMP 공정은 반도체 산업에서 회로의 고집적화와 다층구조를 형성하기 위하여 도입되었으며 반도체 제조를 위한 필수공정으로 그 중요성이 강조되고 있다. 특히 최근에는 Inter-Level Dielectric (ILD)의 형성과 Shallow Trench Isolation (STI) 공정에서실리콘 산화막을 평탄화하기 위한 CMP 공정에 대해 연구가 활발히 이루어지고 있다. 그러나 CMP 공정 후 scratch, pitting corrosion, contamination 등의 Defect가 발생하는 문제점이 존재한다. 이 중에서도 scratch는 기계적, 열적 스트레스에 의해 생성된 패드의 잔해, 슬러리의 잔유물, 응집된 입자 등에 의해 표면에 형성된다. 반도체 공정에서는 다양한 종류의 실리콘 산화막이 사용되고 gks이러한 실리콘 산화막들은 종류에 따라 경도가 다르다. 따라서 실리콘 산화막의 경도에 따른 CMP 공정 및 이로 인한 Scratch 발생에 관한 연구가 필요하다고 할 수 있다. 본 연구에서는 scratch 형성의 거동을 알아보기 위하여 boronphoshposilicate glass (BPSG), plasma enhanced chemical vapor deposition (PECVD) tetraethylorthosilicate (TEOS), high density plasma (HDP) oxide의 3가지 실리콘 산화막의 기계적 성질 및 이에 따른 CMP 공정에 대한 평가를 실시하였다. CMP 공정 후 효율적인 scratch 평가를 위해 브러시를 이용하여 1차 세정을 실시하였으며 습식세정방법(SC-1, DHF)으로 마무리 하였다. Scratch 개수는 Particle counter (Surfscan6200, KLA Tencor, USA)로 측정하였고, 광학현미경을 이용하여 형태를 관찰하였다. Scratch 평가를 위한 CMP 공정은 실험에 사용된 3가지 종류의 실리콘 산화막들의 경도가 서로 다르기 때문에 동등한 실험조건 설정을 위해 동일한 연마량이 관찰되는 조건에서 실시하였다. 실험결과 scratch 종류는 그 형태에 따라 chatter/line/rolling type의 3가지로 분류되었다 BPSG가 다른 종류의 실리콘 산화막에 비해 많은 수에 scratch가 관찰되었으며 line type이 많은 비율을 차지한다는 것을 확인하였다. 또한 CMP 공정에서 압력이 증가함에 따라 chatter type scratch의 길이는 짧아지고 폭이 넓어지는 것을 확인하였다. 본 연구를 통해 실리콘 산화막의 경도에 따른 scratch 형성 원리를 파악하였다.

• Korean Journal of Materials Research
• /
• v.28 no.6
• /
• pp.349-354
• /
• 2018

Particle size reduction is an important step in many technological operations. The process itself is defined as the mechanical breakdown of solids into smaller particles to increase the surface area and induce defects in solids, which are needed for subsequent operations such as chemical reactions. To fabricate nano-sized particles, several tens to hundreds of micron size ceramic beads, formed through high energy milling process, are required. To minimize the contamination effects during high-energy milling, the mechanical properties of zirconia beads are very important. Generally, the mechanical properties of $Y_2O_3$ stabilized tetragonal zirconia beads are closely related to the mechanism of phase change from tetragonal to monoclinic phase via external mechanical forces. Therefore, $Y_2O_3$ distribution in the sintered zirconia beads must also be closely related with the mechanical properties of the beads. In this work, commercially available $100{\mu}m-size$ beads are analyzed from the point of view of microstructure, composition homogeneity (especially for $Y_2O_3$), mechanical properties, and attrition rate.