• Economic and Environmental Geology
• /
• v.51 no.4
• /
• pp.345-358
• /
• 2018

In this study, we have performed electron probe micro analyzer (EPMA), X-ray differaction (XRD), inductively coupled plasma spectroscopy (ICP), Fourier transform Raman spectroscopy (FT-Raman), far-infrared (FIR), nuclear magnetic resonance (NMR), and pH-DO Analyses for characterizing medicinal mineralogy aspect of the black tourmaline (Shantung, china), black and pink tourmaline (Minas Geraris, Brazil), black touemaline (Daeyu mine, Korea). In addition, heating effects of the tourmaline sauna as well as the effects of tourmaline powder-added soap on skin troubles have been investigated. It has been revealed that chemical composition of the tourmaline is either high in Fe-, Al-, B-rich types. Ratio of the K-Ca, Na-K, and Fe-B reflects the component change property of solid solution. $CaO/CaO+Na_2O$ and MgO/FeO+MgO ratio show high positive correlation. When tourmaline reacts with distilled water, extended reaction time DO values approximately decrease and it stabilizes at DO = 10. Otherwise, pH values increase until 6 hours and it stabilizes at pH = 8 after 24 hours. Distilled water changes to alkaline when it reacts with tourmaline powder and particles. Tourmaline showed lower absorption spectrum strength and transmittance at short wave, where absorption spectrum wavelength and strength were determined by the content of the composition elements and characteristics of crystallography. Increase of the Fe content has been confirmed to be the cause for the reduction of irradiation. For the chemical composition and spectral property of the tourmaline particle samples, it has been found that Si and Fe contents show positive correlation with Far-Infrared irradiation, while Al and Mg contents show negative correlation. For tourmaline powder, it has been confirmed that $^{17}O-NMR$ FWHM (full width at half maximum) decreases when reacts with distilled water. Tourmaline sauna (approximately $100^{\circ}C$) was found to increase $0.5-1.5^{\circ}C$ of body temperature, average of 12 heartbeat, and 10mg Hg of blood pressure. Tourmaline soap had very good aesthetic effect to skin and was confirmed to have above the average improvements to skin troubles (e.g., allergy or atopy).

• Journal of Radiation Protection and Research
• /
• v.39 no.4
• /
• pp.199-205
• /
• 2014

In the field of neutron detections, $^3He$ gas, the so-called "the gold standard," is the most widely used material for neutron detections because of its high efficiency in neutron capturing. However, from variable causes since early 2009, $^3He$ is being depleted, which has maintained an upward pressure on its cost. For this reason, the demands for $^3He$ replacements are rising sharply. Research into neutron converting materials, which has not been used well due to a neutron detection efficiency lower than the efficiency of $^3He$, although it can be chosen for use in a neutron detector, has been highlighted again. $^{10}B$, which is one of the $^3He$ replacements, such as $BF_3$, $^6Li$, $^{10}B$, $Gd_2O_2S$, is being researched by various detector development groups owing to a number of advantages such as easy gamma-ray discrimination, non-toxicity, low cost, etc. One of the possible techniques for the detection is an indirect neutron detection method measuring secondary radiation generated by interactions between neutrons and $^{10}B$. Because of the mean free path of alpha particle from interactions that are very short in a solid material, the thickness of $^{10}B$ should be thin. Therefore, to increase the neutron detection efficiency, it is important to make a $^{10}B$ thin film. In this study, we fabricated a $^{10}B$ thin film that is about 60 um in thickness for neutron detection using well-known technology for the manufacturing of a thin electrode for use in lithium ion batteries. In addition, by performing simple physical tests on the conductivity, dispersion, adhesion, and flexibility, we confirmed that the physical characteristics of the fabricated $^{10}B$ thin film are good. Using the fabricated $^{10}B$ thin film, we made a proportional counter for neutron monitoring and measured the neutron pulse height spectrum at a neutron facility at KAERI. Furthermore, we calculated using the Monte Carlo simulation the change of neutron detection efficiency according to the number of thin film layers. In conclusion, we suggest a fabrication method of a $^{10}B$ thin film using the technology used in making a thin electrode of lithium ion batteries and made the $^{10}B$ thin film for neutron detection using suggested method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.275-281
• /
• 2018

It is known that he pollutant emitted from the combustion process of marine fuel oil causes air pollution and harmful effects to the human body. Accordingly, IMO regulates pollutants emitted from ships. However, the regulation of Particulate Matter (PM) is still in the process of debate, so preemptive action is needed. Fundamental research on PM is essential. In this study, the Dimensionless Light Extinction Constant ($K_e$) of fuel oil used in marine diesel engines was measured and analyzed to construct the basic data of the PM generated from marine-based fuel oil. The fuel oil used in the land diesel engine was measured in the same way for character comparison. Both fuel oils differ in sulfur content and density. The $K_e$ was measured via the optical method using a 633 nm laser and was determined by using the volume fraction of PM collected by the gravimetric filter method. The $K_e$ of the PM discharged from marine fuel oil is 8.28, and the land fuel oil is 8.44. The $K_e$ of two fuel oils was similar within the measurement uncertainty range. However, it was found by comparison with the value obtained by the Rayleigh-Limit solution that the light scattering portion could be large. Also, it was found that light extinction characteristics could be different due to the relationship between light transmittance and collected mass.

• Korean journal of food and cookery science
• /
• v.21 no.3 s.87
• /
• pp.301-310
• /
• 2005

The effects of defatted soy flour on the physicochemical characteristics of dough and bread making properties were studied. Defatted soy flour is added to wheat flour for bread-making in order to maximize the use of isoflavones in the soybean. Different particle sizes of both defatted soy flour and wheat flour were prepared by grinding and sievingwith meshes. In the mixograph test, the addition of defatted soy flour to wheat flour increased the requirement for water and decreased the dough development time. Water absorption rates were also investigated to determine the optimum quantity of water for good dough. As the level of defatted soy flour mixed with wheat flour increased, the sedimentation and P.K. values decreased. In comparison with control, the bread made with defatted soy flour especially had a lower specific loaf volume. Specific loaf volume of wheat flour-defatted soy flour bread prepared (Ed- this is an incomplete sentence, it's only a subject clause, and I don't how what you intend to state). In terms of the staling rate and hardness of the wheat flour-defatted soy flour bread, the increased defatted soy flour had a faster staling rate during storage at 5? than at 25? for 5days. From the result of sensory evaluation, wheat flour-defatted soy flour breads containing up to $4\%$ defatted soy flour were rated as being of high quality.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.7
• /
• pp.704-712
• /
• 2006

This research was designed to investigate the removal of heavy metals, such as $Al^{3+}$, $Cu^{2+}$, $Mn^{2+}$, $Pb^{2+}$ and $Zn^{2+}$, by adsorption on clay minerals. Bentonite(Raw-Bentonite), $Ca^{2+}$ and $Na^+$ ion exchanged bentonite(Ca- and Na-Bentonite) and montmorillonite, such as KSF and K10 from Sigma Aldrich, were used as adsorbents. The component of five inorganic adsorbents was analyzed by XRF, and the concentration of metal ions was measured by ICP. The cation exchange capacity(CEC) and the particle charge of adsorbents were measured. The initial concentration range of metal ions was $10{\sim}100$ mg/L. From the experimental results, it was shown that the adsorption equilibrium was attained after $1{\sim}2$ hours. The maximum percentage removal of $Al^{3+}$, $Cu^{2+}$, $Pb^{2+}$ and $Zn^{2+}$ on Na-Bentonite were more than 98% and that of $Mn^{2+}$ was 66%. $Al^{3+}$ was leached out from KSF with the higher concentration of hydrogen ion. Percentage removals of $Pb^{2+}$ and $Zn^{2+}$ on KSF were 88% and 59%, respectively. In general, the percentage removal of metal ions was decreased with the higher initial concentration of metal ions. The adsorption capacity of metal ions on Na-Bentonite was $1.3{\sim}19$ mg/g. Freundlich equation was used to fit the acquired experimental data. As the results, the adsorption capacity of metal ions was in the order of Na-Bentonite$\gg$Raw-Bentonite$\cong$K10>Ca-Bentonite>KSF. Freundlich constant, K of Na-Bentonite was the largest for metal ions. The order K of Na-Bentonite was Al>Cu>Pb>Zn>Mn, and the adsorption intensity(1/n) was determined to be $0.2{\sim}0.39$.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.2
• /
• pp.153-160
• /
• 2009

A PM10 (aerodynamic diameter${\leq}$10 ${\mu}m$) sampler is used to quantify the potential human exposure to suspended particulate matter (PM) and to comply with the governmental regulation. This study was conducted to compare and evaluate the same PM10 cutpoint and different slopes between United States Environmental Protection Agency (USEPA) PM10 sampling criterion and American Conference of Governmental Industrial Hygienists/$Comit\acute{e}$ $Europ\acute{e}en$ de Normalization/International Organization for Standardization thoracic PM10 sampling criterion through theory and experiment. Four PM10 samplers according to the USEPA criterion and one RespiCon sampler in accordance with the thoracic PM10 criterion were used in the present study. In addition, one DustTrak monitor was used to measure real time PM10 mass concentrations. All six aerosol samplers were tested in a PM generation chamber using polydisperse fly ash. Theoretical mass concentrations were calculated by applying the measured particle size distribution characteristics (geometric mean = 6.6 ${\mu}m$, geometric standard deviation = 1.9) of fly ash to each sampling criterion. The measured mass concentrations through a chamber experiment were consistent with theoretical mass concentrations in that a RespiCon sampler with the thoracic PM10 criterion collected less PM than a PM10 sampler with the USEPA criterion. The overall chamber experiment results indicated, when a PM10 sampler was used as a reference sampler, that (1) a RespiCon sampler had a normalizing factor of 1.6, meaning that this sampler underestimated an average 60% of PM10 mass sampled from a PM10 sampler, and (2) a DustTrak real-time monitor using a PM10 inlet had a calibration factor of 2.1.

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.336-342
• /
• 2012

Inorganic materials were commonly used as container media in domestic plant factories. Objective of this research was to secure the information in soil physical and chemical properties of inorganic materials such as vermiculites and perlites. To achieve this, 12 gold and silver vermiculites from China, Zimbabwe, and South Africa and 5 perlites from China were collected based on the marketing grades (MG) in particle sizes and analyzed for determination of their characteristics. The percentage of particles larger than $710{\mu}m$, in China perlite MG 3~5 mm, China silver vermiculites MG > 8 mm and MG 3~8 mm were 99.9%, 99.8%, and 99.7%, respectively, which were much higher than 28.4% in China gold vermiculite MG 0.3~1.0 mm, 14.0% in perlite MG < 1.0 mm, and 12.6% of Zimbabwe silver vermiculite MG < 1.0 mm. The container capacities of perlite MG < 1.0 mm and South Africa silver vermiculite MG 0.25~1.0 mm were 72.0% and 71.1%, respectively. The air space in China silver vermiculite MG 3~8 mm was 49.3% which was higher than other materials tested. However, the China gold and silver vermiculites MG 0.3~1 mm had 3.5% and 2.4% in air space indicating that possible problems could occur in soil aeration when they are used for container media. The percentage of easily available and buffering water of China gold vermiculite MG 0.3~1 mm and perlite MG < 1.0 mm were the highest among test materials. The ranges of pH and electrical conductivity were 6.36 to 10.7 and 0.032 to $0.393dS{\cdot}m^{-1}$ in vermiculites and 7.78 to 8.62 and 0.030 to $0.041dS{\cdot}m^{-1}$ in perlite, respectively. The cation exchange capacity of China silver vermiculite MG 0.3~1 mm were $14.7cmol{\cdot}kg^{-1}$ that was 10 times as high as $0.34cmol{\cdot}kg^{-1}$ in perlite MG 1~2.5 mm. The vermiculites had the higher contents of exchangeable cations such as Ca, K, and Na, than those of perlites.

• Korean Journal of Soil Science and Fertilizer
• /
• v.30 no.1
• /
• pp.56-61
• /
• 1997

A study was carried out to find out the basic information in physical properties for selection and manufacturing the good seedling media through the analysis of the physical properties, such as particle size, water retention and three phases of the major horticultural substrates. Easily available water(EAW), the water contents between 1kPa and 5kPa water potental, was highest in peatmoss with 39%, and perlite 34.0%, vermiculite 16.9%, but the values of osmunda and bark were lower than 4.8%. Water buffering capacity(WBC), the water content between 5kPa and 10kPa, was 6.1% in peatmoss and 2.3% in vermiculite but it was lower than 1.0% in other substrates. To adjust the suitable range of water potential at crossing point of water and air curves to 1.5~2.5kPa, more finer materials were needed in osmunda and bark, and more coarser materials must be added to peatmoss, perlite and vermiculite. Water potentials of substrates in saturated pot condition were equivalent to 2.2kPa in peatmoss and others were ranged in 1.0kPa to 4.3kPa of water potential in pressure chamber.

• Journal of Life Science
• /
• v.18 no.4
• /
• pp.515-521
• /
• 2008

This experiment was conducted to investigate effects of non-ionic or zwitterionic (+/-) surfactants on digestibility of rice straw, and changes of growth of rumen mixed microbes, pH, and gas production during in vitro fermentation. Also, during in vitro ruminal fermentation, microbial attachment on rice straw was investigated using scanning electron microscopy (SEM). Tween 80 or SOLFA-850 for non-ionic surfactant (NIS), and 3-(Dodecyldimethylammonio) propanesulfanate (DDAP) for zwitterionic surfactant (ZIS) was supplemented by 0.05% and 0.1% in Dehority's artificial medium containing Holtein rumen fluid, respectively, and the substrate for fermentation was rice straw passed through 1 mm screen. The experiment was composed of 7 treatments (two levels of two NISs, two levels of a ZIS) including the control, and 6, 12, 24, 48 and 72 hr of fermentation time with 3 replications per treatment. Treatment of Tween 80 increased in vitro DM digestibilities during 48 hr and 72 h post fermentations compared to the other treatments, whereas treatment of DDAP as a ZIS resulted in decreased DM digestibility than that of the control from 24 hr post fermentation (P<0.05). Gas production in vitro was greater (P<0.05) with addition of NIS than the control or ZIS, and increased as fermentation time elapsed. Rumen mixed microbial growth was greatest with addition of Tween 80 as NIS, and lowest when DDAP as ZIS was supplemented to the fermentation tube (P<0.05). In SEM observation, rumen microbial population attached on rice straw particle was greater with addition of NIS, but was less with addition ZIS compared with the control. In conclusion we could not found any positive effects of ZIS surfactants on rumunal fermentation characteristics and rumen microbial growth rates.

• Korean Journal of Remote Sensing
• /
• v.37 no.6_2
• /
• pp.1793-1801
• /
• 2021

From 2015 to June 2020, the backscattering coefficients of 532 and 1064 nm measured using LIDAR and the depolarization ratio at 532 nm were used to separate the backscattering coefficient at 532 nm as three types as PM₁₀, PM_2.5-10, PM_2.5 according to particle size. The mass extinction efficiency (MEE) of three types was calculated using the mass concentration measured on the ground. The overall mean values of the calculated MEE were 5.1 ± 2.5, 1.7 ± 3.7, and 9.3 ± 6.3 m²/g in PM₁₀, PM_2.5-10, and PM_2.5, respectively. When the mass concentration of PM₁₀ and PM_2.5 was low, higher than average MEE was calculated, and it was confirmed that the MEE decreased as the mass concentration increased. When the MEE was calculated for each type according to the mixing degree of Asian dust, PM_2.5-10 was twice at pollution aerosol as high as 2.1 ± 2.8 m²/g, compare to pollution-dominated mixture, dust-dominated mixture, and pure dust of 1.1 ± 1.8, 1.4 ± 3.3, 1.1 ± 1.5 m²/g, respectively. However, PM_2.5 MEE showed similar values irrespective of type: 9.4 ± 6.5, 9.0 ± 5.8, 10.3 ± 7.5, and 9.1 ± 9.0 m²/g. The MEE of PM₁₀ was 5.6 ± 2.9, 4.4 ± 2.0, 3.6 ± 2.9, and 2.8 ± 2.4 m²/g in pollution aerosol (PA), pollution-dominated mixture (PDM), dust-dominated mixture (DDM), and pure dust (PD), respectively, and increased as the dust ratio value decreased. Even if the same type according to the same mass concentration or Asian dust mixture was shown, as the PM_2.5/PM₁₀ ratio decreased, the MEE of PM_2.5-10 decreased and the MEE of PM_2.5 showed a tendency to increase.