• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.807-813
• /
• 2014

The Ag-impregnated activated carbon was produced from bamboo activated carbon by soaking method of silver nitrate solution. The carbonization and activation of raw material was conducted at $900^{\circ}C$. Soaking conditions are the variation of silver nitrate solution concentration (0.002~0.1 mol/L) and soaking time (maximum 24 h). The specific surface area and pore size distribution of the prepared activated carbons were measured. Also, NO and activated carbon reaction were conducted in a thermogravimetric analyzer in order to use for de-NOx agents of used activated carbon. Carbon-NO reactions were carried out with respect to reaction temperature ($20{\sim}850^{\circ}C$) and NO gas partial pressure (0.1~1.8 kPa). As results, Ag amounts are saturated within 2h, Ag amounts increased 1.95 mg Ag/g (0.2%)~ 88.70 mg Ag/g (8.87%) with the concentration of silver nitrate solution in the range of 0.002~0.1 mol/L. The specific volume and surface area of bamboo activated carbon of impregnated with 0.2% silver were maximum, but decreased with increasing Ag amounts of activated carbon due to pore blocking. In NO reaction, the reaction rate of impregnated bamboo activated carbon was retarded as compare with that of bamboo activated carbon. Measured reaction orders of NO concentration and activation energy were 0.63[BA], 0.69l[BA(Ag)] and 80.5 kJ/mol[BA], 66.4 kJ/mol[BA(Ag)], respectively.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 2000

All solid-state thin film micro-batteries consisting of lithium metal anode, an amorphous LiPON electrolyte and cathode of vanadium oxide have been fabricated and characterized, which were fabricated with cell structure of $Li/LiPON/V_2O_5Pt$. The effect of various oxygen partial pressure on the electrochemical properties of vanadium oxide thin films formed by d.c. reactive sputtering deposition were investigated. The vanadium oxide thin film with deposition condition of $20\%\;O_2/Ar$ ratio showed good cycling behavior. In in-siか process, the LiPON electrolyte was deposited on the $V_2O_5$ films without breaking vacuum by r.f. magnetron sputtering at room temperature. After deposition of the amorphous LiPON, the Li metal films were grown by a thermal evaporator in a dry room. The charge-discharge cycle measurements as a function of current density and voltage variation revealed that the $Li/LiPON/V_2O_5$ thin film had excellent rechargeable properly when current density was $7{\mu}A/cm^2$. and cut-off voltage was between 3.6 and 2.7V In practical experiment, a stopwatch ran on this $Li/LiPON/V_2O_5$ thin film micro-battery. This result means that thin film micro-battery fabricated by in-siか process is a promising for power source for electronic devices.

• The Korean Journal of Physiology and Pharmacology
• /
• v.1 no.6
• /
• pp.749-758
• /
• 1997

Myocardial ischemia-reperfusion injury is known to be mediated by reactive oxygen species. The myocardial cell is equipped with endogenous antioxidant defensive system which can be adaptively stimulated by various oxidative stress. It is postulated that an increased oxygen partial pressure induced by hyperbaric oxygenation impose an oxidative stress on the cells, resulting alterations in the endogenous antioxidant system. In this study we investigated the effect of hyperbaric oxygenation on the activities of myocardial antioxidant enzymes and observed whether the hyperbaric oxygenation could protect the ischemia-reperfusion injury of heart. Rats or rabbits were pretreated with hyperbaric $oxygenation(2{\sim}3\;atm\;O_2/1{\sim}3\;hrs/1{\sim}10\;days)$. The changes in activities of major antioxidant enzymes(superoxide dismutase, catalase, glutathione peroxidase, glutathione reductase, glucose-6-phasphate dehydrogenase), functional recovery and infarct size were observed in the experimentally induced ischemia-reperfused hearts. In the hearts isolated from rats pretreated with $2\;atm\;O_2/1{\sim}2\;hrs$ for 5 days, the functional recovery after reperfusion(20 min) following global ischemia(25 min) was significantly increased without any observable oxygen toxicity. Lactate dehydrogenase release was also significantly reduced in this hyperbaric oxygenated rat hearts. In in vivo regional ischemia(30 min) model of rabbit hearts, pretreatrment with $2\;atm\;O_2/1\;hr$ for 5 days significantly limited the infarct size. Among the myocardial antioxidant enzymes of rat hearts pretreated with the hyperbaric oxygenation, the activities of catalase, superoxide dismutase and glucose-6-phosphatase dehydrogenase were increased, while those of glutathione peroxidase and reductase were not changed. There were lethal cases in the groups of rats exposed to 3 atm $3\;atm\;O_2/2{\sim}3\;hrs$ for 5 days. A lipid-peroxidation product, rnnlondialdehyde was increased in brains and livers of the rats exposed to$2\;atm\;O_2/2{\sim}3\;hrs/5\;days\;and\;3\;atm\;O_2/1\;hr/5days$. The present results suggest that the pretreatment of hyperbaric oxygenation can protect the post-ischemic rererfused hearts in association with a stimulation of the activities of myocardial antioxidant defensive enzymes, and that the hyperbaric oxygenation of $2\;atm\;O_2/1\;hr$for 5 days would be a safe condition which does not produce any oxygen toxicity.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.3
• /
• pp.473-480
• /
• 2007

The dentigerous cyst originates through alteration of stellate reticulum after amelogenesis has completed, with accumulation of fluid between the layers of the reduced enamel epithelium or between this epithelium and the tooth crown. Its incidence is relatively high on 10s or 20s of age and it is always related to the unerupted crown. Generally, it has no symptom, however, if the cyst is large or accompanied with pus formation, swelling and pain may occur. In radiographic findings, it shows impacted crown surrounded by well defined unilocular radiolucent lesion and occasionally displacement of adjacent teeth or root resorption. The goal of treatment is complete elimination of abnormal tissue preserving the tooth involved in the cyst. Enucleation and marsupialization are commonly used for the treatment. Marsupialization is the procedure which removes the partial portion of the cystic wall and connects with the oral mucosa. As the pressure in the cyst decreases, bone regeneration takes place in the defect area and cystic wall converts into normal mucosa. This procedure, however, is the most conservative procedure which allows the protection of adjacent important structures. If the eruption space is sufficient, then inducing the eruption of the permanent tooth in the cyst is also possible. In following cases, dentigerous cyst was diaganosed after clinical and radiographic examination. Marsupialazation was done to remove the cyst and induce the tooth, which was in the cyst, to erupt into the oral cavity.

• Applied Chemistry for Engineering
• /
• v.9 no.1
• /
• pp.13-19
• /
• 1998

Copolyimide membranes of different chemical structure based on pyromellitic dianhydride (PMDA)/methylendianiline(MDA) were prepared by varying their chemical compositions with adding meta-phenylendiamine (MPD), para- phenylendiamine (PPD), 2,4,6- trimethyl-1,3-phenylenediamine(TriMeMPD) as a co-monomer. The $N_2$ and $O_2$ permeation properties are qualitatively correlated to specific free volume and intersegmental distance of membrane. The partial replacement of MDA with MPD or PPD caused in the PMDA/MDA based membranes increase in density, and decrease in free volume, d-spacing, consequently resulted in decreased permeability coefficient. In the case of TriMeMPD, opposite results were observed. In all membranes, the permeability coefficients were pressure independent, and membranes which have high permeability coefficient showed low $N_2/O_2$ ideal separation factor as an usual manner. The permeability coefficient also increased with temperature and $N_2/O_2$ ideal separation factor decreased. The increase ratio of the $N_2$ permeability coefficient was larger than that of $O_2$.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.836-842
• /
• 1994

The optimum design conditions of gas sparger pipe and the effects of operating variables on $SO_2$ removal efficiency have been examined in Jet Bubbling Reactor. Geometry of gas sparser pipe of Jet Bubbling Reactor is a very important factor to obtain a effective gas-liquid contact. Test results revealed that Reynolds numbers at sparger and slot have to be kept greater than 12,000 identically at a given gas velocity. $SO_2$ removal efficiency was a function of ${\Delta}P$, pH, inlet $SO_2$ concentration and particle size of limestone and was more sensitive to the change of ${\Delta}P$ than to the changes of others. The ${\Delta}P$ of at least 230mmAq must be maintained to acheive the above 90% $SO_2$ removal at pH of 4.0 which is considered as adequate operating pH. Higher $SO_2$ removal efficiency was obtained even at lower pH ranges, which resulted from the complete oxidation of the absorbed $SO_2$ to sulfates by adding air and consequently from the reduction of $SO_2$ equillibrium partial pressure in the gas-liquid interface The 99.5% of the limestone utilization was attained in pH range from 3.0 to 5.0 with regardless to the particle size of limestone employed.

• Applied Chemistry for Engineering
• /
• v.26 no.5
• /
• pp.604-608
• /
• 2015

In the present work, the improvement of nitrate removal ability was investigated to resolve a eutrophication problem by using Ulmus davidiana (U. davidiana) bark generated from Gangwon province. When the initial pH of aqueous solution was adjusted to 3.5 in batch experiments, the removal efficiencies for 10 and 20 mg/L nitrate increased up to 43 and 37%, respectively. In addition, when U. davidiana bark of 1.0 g/100 mL was used for 8 h, the removal efficiency for 20 mg/L nitrate was 68%. Moreover, when reforming reaction of U. davidiana bark was performed under oxyfluorination conditions, the optimal ratio of partial pressure between fluorine and oxygen was 1 : 9 for an enhanced nitrate adsorption amount. When reformed U. davidiana bark was used for 8 h operation under the optimal oxyfluorination condition, removal efficiencies for 10, 20 and 40 mg/L nitrate were found to be 96, 95 and 59%, respectively. Collectively, these results suggest that our water treatment technology can be effectively utilized to treat high concentrations of nitrate in water bodies.

• Journal of Chest Surgery
• /
• v.9 no.2
• /
• pp.220-238
• /
• 1976

Six cases of congenital heart disease were operated on by means of cardiopulmonary bypass between December, 1975 and April, 1976. Two cases of ventricular septal defects (VSD), two cases of VSD, associated with ruptured aneurysm of sinus Valsalva, two cases of atrial septal defects (ASD) and one case of pulmonic stenosis with patent ductus arteriosus were operated. Sarns roller pumps and Bentley Temptrol oxygenators were used for extracorporeal circulation. Pump oxygenator was primed with Ringer's lactate solution, 5% dextrose in water, mannitol, and ACD blood. Flow rate ranged from 2.0 to $2.4L/M^2/min$. Bicarbonate was added to the oxygenator with estimated amount as 15 mEq/L/hr. Venous catheters were introduced into superior and inferior vena cava, and oxygenated blood was returned to the body through aortic cannula inserted into ascending aorta. Moderate hypothermia ($30^{\circ}C$) was induced by core cooling. Aorta was cross clamped for 15 minutes and released for 3 minutes, and repeated clamping when necessary. Atrial and ventricular septal efects were closed by direct sutures. Aneurysms of sinus Valsalva ruptured into the right ventricle were repaired through right ventriculotomy by d:rect closure with Dacron patch reinforcement. Cardiopulmonary bypass time varied from 66 to 209 minutes, and aorta cross clamping time ranged from 13 to 56 minutes. Postoperative bleeding was minimal except one case who needed for evacuation of substernal hematoma. Intra- and postoperative urinary output was satisfactory. Acid-base balance, partial pressure of $O_2$, electrolytes, and hematological changes during intra- and post-perfusion period remained at the acceptable ranges. No mortality was experienced.

• Korean Journal of Microbiology
• /
• v.41 no.3
• /
• pp.164-167
• /
• 2005

The culture condition and medium composition for the enhanced mycelial growth of Lepista nuda DGUM 26501 were investigated. The optimal temperature and pH for the mycelial growth were $24^{\circ}C$ and $7.0\~8.0$, respectively. The partial pressure of oxygen for the enhanced mycelial growth was more than $10\%\;O_2$. When Czapek-Dox medium was used as a minimal medium, manitol and xylitol were very good carbon sources. Organic nitrogen sources were better than inorganic ones for mycelial growth. As the nitrogen source tested, com steep liquor, soytone and protease peptone were the best as a source of organic nitrogen sources. When ammonium phosphate as phosphorus sources was used, the enhanced mycelial growth was shown. Nicotinic acid was proved to be the most appropriate source of vitamin. After the mycelia of L. nuda DGUM 26501 was cultivated at $24^{\circ}C$ for 10 days in LNM broth (pH 7.0), the activities of extracellular enzyme were determined. The specific activity of $\alpha-amylase$ was much higher than those of other enzymes. However, little or no enzyme activities of $\beta-glucosidase$, CMCase, laccase and lipase were found.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.437-444
• /
• 2000

Propylene polymerizations were carried out by using rac-Et(Ind)$_2$ZrCl$_2$ (Zirconocene catalyst) and a commercial third generation Ziegler-Natta catalyst in a semibatch reactor. From the polymerization reactions, the optimum reaction conditions and the physical properties of polymers produced from each catalyst system were investigated. The optimum reaction temperatures of rac-Et(Ind)$_2$ZrCl$_2$ and Ziegler-Natta catalyst were 5$0^{\circ}C$, 4$0^{\circ}C$, respectively. On the basis of the results for the produced polymer particle size distributions and the catalytic activities of polymerization reaction, the reaction temperature should be considered as an important factor for the successful polymerization reactions. Especially, the polymer was conglomerated in the higher reaction temperature. It was found that there was an upper limitation to co-catalyst concentration. Reaction rates and polymer yields rather decreased with increasing the concentration of to-catalyst, i.e., MAO and TEAl affected only polymerization activities, but the PEEB in Ziegler-Natta catalyst system affected isotactic indexes of produced polymer as well as activities. Based on these observations, the production yield seems to exhibit a first order lineal relationship to the partial pressure of monomer.