• 한국유체기계학회 논문집
• /
• 제7권6호
• /
• pp.28-37
• /
• 2004

An experimental study is conducted to investigate flow characteristics on a small axial-type turbine which is applied as the rotating part of air tools. It operates in a partial admission due to consumption restriction of the high pressure air. In this operating condition, it is necessary to understand flow characteristics for obtaining the high specific output power. Tested turbine consists of two stages and the mean radius of flow passage is less than 10mm. A 6 bar pressure air is used to operate the turbine. The experimental results show that flow angles depend on the measuring location along the circumferential direction, but its discrepancy is alleviated along the axial direction. Absolute flow velocities show three times difference according to the measuring location at the exit of the first rotor due to the partial admission, but they show similar value at the exit of the second rotor by the velocity diffusion. From the measured flow angles and velocities, a ratio of output power obtained by the first and second rotor is estimated. It shows that the output power obtained by the second rotor is about $11\%$ to that by the first rotor at 60,000 RPM. It is effective therefore to improve the first rotor for increasing the turbine output power.

• 한국유체기계학회 논문집
• /
• 제5권4호
• /
• pp.11-18
• /
• 2002

A turbopump system composed of two pumps and one turbine is considered. The turbine composed of a nozzle and a rotor is used to drive the pumps while gas passes through the nozzle and potential energy is converted to kinetic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of turbine system is investigated with some pre-determined design requirements (i.e., pressure ratio, rotational speed, required power, etc.) following Liquid Rocket Engine (L.R.E.) system specifications. For simplicity of turbine system, impulse-type rotor blades for open-type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow-rate compared to close-type system. In this study, a partial admission nozzle is adopted to maximize the efficiency of the open-type turbine system. A design methodology of turbine system was introduced. Especially, partial admission nozzle was designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design is presented for a 10 ton thrust level of L.R.E.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.145-152
• /
• 2000

A turbopump system composed of two pumps and one turbine is considered. The turbine composed of a nozzle and a rotor is used to drive the pumps while gas passes through the nozzle, potential energy is converted to kinematic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of turbine system is investigated using compressible fluid dynamic theories with some pre-determined design requirements (i.e., pressure ratio, rotational speed, required power etc.) obtained from liquid rocket engine (L.R.E.) system design. For simplicity of turbine system, impulse-type rotor blades for open type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow rate compared to close-type system. In this study, a partial admission nozzle Is adopted to maximize the efficiency of the open-type turbine system. A design methodology of turbine system has been introduced. Especially, partial admission nozzle has been designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design for a 10 ton thrust level of L.R.E is presented.

• 플랜트 저널
• /
• 제4권3호
• /
• pp.60-65
• /
• 2008

Power plant industry has been developed at high-capacity, high-technology, and innovation. Steam turbine became the most useful equipment that dominate more than 50% of all the world electricity production. And developed new materials of the turbine blade and extended length of the turbine last blade brought reform in steam turbine performance upgrade. In this paper, when do partial load driving in high-capacity steam turbine, optimum driving method found whether there is something. In operating steam turbine, there is a lot of loss from secondary wake and throttle of the 1st stage nozzle by the biggest leading factor that load fluctuation affects in high-pressure steam turbine performance. Effect of internal efficiency by 1 stage nozzle is the biggest here, but here fluid flow and flow analysis were not yet examined closely definitely. So, Analyzed design data and acceptance performance test result to applying subcritical pressure drum type 560 MW, supercritical-pressure once through type 500 MW, and 800 MW steam turbines actually. In conclusion, at partial load driving, partial arc admission(PAA) is more efficient than full arc admission(FAA) efficiency. This is judged by because increase being proportional with gross energy of stream that is pressure - available energy if pressure of stream that is flowed in to the turbine increases, available energy becomes maximum and turbine efficiency improves. Therefore, turbine performance is that preview that first stage performance fell if decline is serious in partial load because first stage performance changes according to load.

• 한국항공우주학회지
• /
• 제38권9호
• /
• pp.943-954
• /
• 2010

본 연구에 적용된 터빈은 반경류형이며, 동익의 외경은 108 mm이다. 터빈은 1.4-4.1%의 낮은 부분분사율에서 작동하므로 익형은 축류형으로 설계되었으며 3단으로 구성되었다. 터빈에서 부분분사율과 팁간극 및 노즐유동각의 변화에 따른 성능의 변화를 측정하였다. 또한 터빈의 단수를 변경하면서 각 단수에서 발생되는 출력의 차이에 대한 측정이 이루어졌다. 본 연구의 터빈은 다양한 작동조건에서 운전되므로 넓은 작동범위에 따른 비교를 위하여 회전수를 변경하면서 탈설계 영역에서의 성능 평가가 이루어졌다. 뿐만 아니라 다양한 작동조건에 합당한 시스템의 평가를 위하여 총비오크가 얻어졌다. 아울러 소형터빈의 설계 및 성능예측을 위하여 유동해석을 수행하였으며 얻어진 예측의 결과는 실험으로 얻어진 결과와 잘 일치하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.391-397
• /
• 2004

The performance characteristics of partial admission supersonic turbines are analyzed by using the commercial CFD program FLUENT6.0. The governing equations were discretized with Euler implicit method in time and 2nd-order upwind scheme of FVM in space. The k-$\varepsilon$ turbulence model was utilized to describe the turbulent flow field. In order to investigate the nozzle--rotor interactions and the effect of partial admission, the flows in supersonic turbine rotor cascades with a nozzle are computed. Extensive computations of partial admission supersonic turbines provide the shock structures and flow patterns in the nozzle and rotor. It is clearly shown that the nozzle flow is highly affected by the shocks or expansion waves propagated from the rotor leading edge. And the rotor flow is also affected by the shocks or wakes originated from the nozzle.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권3호
• /
• pp.396-404
• /
• 1998

A numerical analysis is presented for the transient behavior of a rotating turbines blades. The response due to partial admission during start-up and resonance pass is considered, Modal analysis and numerical integation method are used for solving the problems A theory for determining the material and aerodynamic damping values of turbine blades is presented. The damping values of the various modeling of blaes-uniform beam and tapered twisted beam-are calculated and the influence on blades response is investigated. The effect of angular velocity on transient response are also shown.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.601-602
• /
• 2002

Numerical simulation using well-known commercial software Fine/Turbo is applied to the analysis of the aerodynamic performance for the supersonic turbine system with partial admission nozzle. Calculation was performed for coupled system of nozzle and blades using mixing plane method. In addition, calculations were also performed for the blades alone to investigate the effect of the performance variation with blade profile. These computational results are compared with the experiments. The agreement between the prediction and the experiment was found to be satisfactory..

• 한국추진공학회지
• /
• 제12권6호
• /
• pp.21-29
• /
• 2008

본 연구에서는 부분분사에서 작동하는 소형 축류형 터빈에서, 중요한 설계변수인 노즐에서의 출구유동각과 동익에서의 현절비를 변경하였을 때 발생되는 성능변화에 대하여 실험적인 연구를 수행하였다. 성능시험에 사용된 터빈은 단단으로 구성되며 로터의 평균반경은 35mm였다. 실험에서 최적의 설계변수를 찾기 위하여 세 가지의 현절비와 네 가지의 노즐에서의 출구유동각을 적용하였다. 터빈에서의 전체적인 성능평가를 위하여 총비출력으로 비교하였으며, 부분분사율이 3.4%인 경우에 동익에서의 현절비가 2.18일 때 최고의 성능이 얻어졌다. 이 값은 전분사 시에 적용되는 최적의 현절비에 비하여 74%나 증가한 결과이다.

• 한국추진공학회지
• /
• 제12권4호
• /
• pp.48-55
• /
• 2008

본 연구에서는 파이로 시동기의 고온고압 가스에 의해 구동되어지는 부분입사형 초음속 터빈의 익렬 엣지 형상에 따른 터빈 블레이드의 표면 가스온도 분포를 분석하기 위하여 초음속 터빈 내부의 온도발달 특성 해석을 실시하였다. 시동 초기의 터빈 블레이드의 표면 가스온도 분포 발달을 살펴보기 위해서 각각의 엣지 형상에 대해 터빈의 회전수를 바꾸어가며 계산을 수행하였다. 터빈 블레이드 엣지 형상은 샤프형과 라운드형 두 가지 종류를 선택하였고, 터빈의 회전수는 두 가지 형상 모두 $0{\sim}10,000rpm$의 회전 속도를 주어 계산을 실시하였다. 터빈의 회전수가 증가할수록 터빈 블레이드 표면의 평균 온도는 하강하였고, 사프형 엣지 형상이 라운드형 엣지 형상에 비해서 터빈 블레이드의 표면 온도 분포가 전반적으로 낮은 분포를 나타내었다.