• 암석학회지
• /
• 제1권2호
• /
• pp.91-103
• /
• 1992

Eruptive mechanisms and processes at Udo tuff cone can be inferred from indicative characters of products, bedforms and lithofacies, and ring faults. In terms of bedforms and lithofa-cies in particular, massive lapilli tuff beds and chaotic lapilli tuff beds are derived from subaerial falls of aggregated tephra of wet tephra finger jets, occurring dominantly at the lower sequences of proximal part at the tuff cone. Crudely stratified lapilli tuff are derived from subaerial falls of slightly aggregated tephra of less wet tephra finger jets, whereas reversely graded lapilli tuff beds are from slightly disaggregated subaerial falls of continuous uprush. Both beds frequently occur in the middle sequences at proximal and near medial part of the tuff cone. Block and lapilli tephra lenses, ash-coated lapilli tephra beds(lenses) and thin-bedded tuff beds are derived from extremely disaggregated subaerial falls of dry tephra in the continuous uprush, frequently occurring at the upper sequences of medial part at the tuff cone. Udo tuff cone is a basaltic volcano emergent through the sea water surface while water could flood across or into the vent area. Emergence of the tuff cone was from the type-Surtseyan eruption characterized by earlier tephra finger jets and later continuous uprush columns of tephra with copious volumes of steam. Explosions began when boiling of wter produced a bubble column reducing the hydrostatic pres-sure, allowing exsolution of gases from the magma. This expansion of magma into a vesiculating froth fragmented the magma and permitted mixing of magma and water so that a more vigorous generation of steam could proceed. Tephra finger jetting explosions continued to build the crater rims, then remove water from the vent that their deposits flowed like slsurries until the continuous uprush explosion ensued. Continuous uprush explosions were associated with most rapid accumula-tion of tephra. The increasing volume rate led to partial removal of water from the vent area by the newly tephra ring so that more vigorous activity could be attended by a reducing water supply. This might restrain surplus of cold water entering the vent and thus enhance the vigour of the eruption by allowing optimal heat exchange. Eventually the crater became so deep and unsuported that piecemeal sliding, or massive subsidence on indipping ring faults, filled and closed the vent, and the cycle of explosions and collapse began anew.

• Journal of Chest Surgery
• /
• 제29권2호
• /
• pp.177-184
• /
• 1996

1987년부터 1994년까지 서울대학교병원 흉부외과에서 흉복부 대동맥류의 진단하에 외과적 치료를 받은 환자는21명이었다. 이 환자들의 나이는20세부터 67세까지 다양하게 분포하였으며, 평균연령은 41.5세 였다. 남녀는 각각 11명, 10명이었다. 증상으로는 대부분의 환자들이 신체의 한 부분의 동통을 호소했는데, 배부동통이 가장 많았고, 흉통과 흉부의 불쾌감, 옆구리 동통 등도 호소했으며, 증상이 없었던 경우도 3례 있었다. 21례 중 15례(71.4%)가 만성 해리성 대동맥류였으며, 6례 (28.5%)가 진성 대동맥류였다. 만성 해리성 대동맥류 환자중 고혈압과 연관된 동맥경화증이 6례(28.5%)에서 관찰되었으며, Martian증후군이 5례 (2).8%)의 환자에서 확인되 었고, 2례 (9.5%)는 임신이 원 인으로 판단되 었다. 대동맥류의 크기는 6~12cm까지 다양했고, Crawford 분류에 따라 분류하면, Type I 이 7례 (33.3%), Type II가 8례 (38.1%)였고, Type R과 Type W가 각각 3례 (14.3%)씩 있었다. 한 예를 제외한 모든 환자에서 질환이 있는 부위의 대동맥을 인조혈관으로 치환하는 수술을 시행하였고, 한 예 에서만 가성동맥류로 인한 질환으로 진단되어 동맥벽의 열상\ulcorner위를 일차봉합하였다. 대동맥 교차차단시 근위부의 고혈압 및 그로인한 뇌척수액압 증가를 막고, 원위부의 허혈상태의 교정 및 척수허혈을 방지하고, 혈역학적 조절을 용이하게 하기위하여 우회술을 시행하였는데 21명의 환자 중, 12례(57.1%)에서는 대퇴동맥과 대퇴정맥, 또는 대퇴동맥과 폐동맥에 캐늘라를 상관하여 부분적 체 외순환을 시행하였고, 4례 (19.0%)에서는 Biopump를 좌심실심이와 대퇴동맥에 상관하여 우회술을 시행하였으며, 체와순환술과 일시적 완전순환정지를 이용한 예가 2례 (9.5%), Gott씨 도관을 이용한 단락술을 실시한 예가 1례 (4.7%) 있었으며, 우회술물 시행하지 않고 단순 대동맥 교차차단만으로 수술을 시행한 경우도 2례 (9.5%) 있었다. 수술후 발생한 합병증으로는 5례 (23.8%)에서 일측 성대신경 손상으로 인한 애성이 발생하였고, 창상감염이 4례(19.0%), 하반신 마비가 2례 (9.5%), 유미흉이 1례 (4.7%)에서 발생하였다. 병원사망율은 9.5%로 2례 있었고, 만기 사망례는 없었다. 결론적으로, 중요합병 증 발생율과 사망율이 비교적 낮았고, 외래 추적조사 결과 퇴원환자 모두 양호한 건강상태를 유지 하고 있었기에, 흉복부 대동맥류의 丙珦岵\ulcorner치료는 이제 더이상 고위첨도의 수술이 아니라고 여겨지며, 수술의 적응증이 되는 환자에게는 조기에 수술을 권유하는 것이 좋으리라 판단된다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2001년도 추계학술강연 및 발표대회
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• 한국재료학회지
• /
• 제13권6호
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.