• 한국자기학회지
• /
• 제12권2호
• /
• pp.51-56
• /
• 2002

마그네트론 스퍼터링을 이용하여 퍼멀로이 박막의 제조시 요구되는 자기이방성 조절을 위하여 필요한 조건을 NdFeB자석과 3-D전산모사를 이용하여 평가하였으며, 또한 같은 조건에서 제조된 박막의 특성을 조사하였다. 타겟과 기판과의 거리가 5cm인 경우 타겟 자석과 자기이방성 조절을 위하여 장입된 영구자석의 상호 작용에 의하여 기판에 평행한 자속을 얻기 위한 조건이 전산모사 결과 영구자석간의 거리 변화에 매우 민감하였으며, 최적의 조건의 두 영구자석의 간격이 70mm에서 가장 균질한 자속을 대면적에서 얻을 수 있음이 확인되었다. 투입전력 450 W에서 기판에 장착시킨 NdFeB 자석간 거리(48, 60, 70, 80, 85mm) 를 변화시킨 결과 포화자화 값은 10~12 kG, 보자력은 0.2~1 Oe, 비저항은 20 $\mu$$\Omega$cm의 값을 갖는 퍼멀로이가 제조되었으며, 자기적 이방성은 전산모사의 결과와 일치하였다. 그 결과 자석간의 간격이 70mm에서 제조된 두께 1 $\mu$m 퍼말로이의 유효투자율이 10 MHz에서 2500을 유지하는 결과를 얻었다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.5-10
• /
• 2007

We prepared four different $MgB_2$ films on $Al_2O_3$ by hybrid physical chemical vapor deposition method with thicknesses ranging from $0.65\;{\mu}m$ to $1.2\;{\mu}m$. X-ray diffraction patterns confirm that all the $MgB_2$ films are c-axis oriented perpendicular to $Al_2O_3$ substrates. The superconducting onset temperature of $MgB_2$ films were between 39.39K and 40.72K. The residual resistivity ratio of the $MgB_2$ films was in the range between 3.13 and 37.3. We measured the angle dependence of critical current density ($J_c$) and resistivity, and determined the upper critical field ($H_{c2}$) from the temperature dependence of the resistivity curves. The anisotropy ratios defined as the ratio of the $H_{c2}$ parallel to the ab-plane to that perpendicular to the ab-plane were in the range of 2.13 to 4.5 and were increased as the temperature was decreased. Some samples showed increase of $J_c$ and decrease of resistivity when a magnetic field in applied parallel to the c-axis. We interpret this angle dependence in terms of enhanced flux pinning due to columnar growth of $MgB_2$ along the c-axis.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.84-89
• /
• 2014

This paper presents an analytical prediction and experimental verification of the electromagnetic performance of a parallel magnetized surface-mounted permanent magnet (SPM) motor having a fractional number of slots per pole combination. On the basis of a two-dimensional (2-D) polar coordinate system and a magnetic vector potential, analytical solutions for flux density produced by the permanent magnets (PMs) and stator windings are derived. Then, analytical solutions for back-electromotive force (emf) and electromagnetic torque are derived from these field solutions. The analytical results are thoroughly validated with 2-D nonlinear finite element (FE) analysis results. Finally, the experimental back-emf and electromagnetic torque measurements are presented to test the validity of the analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.6-9
• /
• 2000

InSb hall effect of multilayerd structures were investigated. According to variation of magnetic field measured hall coefficient, Hall mobility, carrier density and hall voltage. For the measurement of electrical properties of hall device, evaperated InSb thin film fabricated with series and parallel multilayers. We found that the XRD analysis of InSb thin film showed good properties at $200^{\circ}C$, 60 minutes. Resistance of ohmic contact increased linearly due to increasing current. Some of device fabrication technique and analysis of Hall effect were discussed.

• Smart Structures and Systems
• /
• 제6권2호
• /
• pp.101-113
• /
• 2010

This paper presents the results of a series of experiments conducted to model a magnetorheological damper operated in shear mode. The prototype MR damper consists of two parallel steel plates; a paddle covered with an MR fluid coated foam is placed between the plates. The force is generated when the paddle is in motion and the MR fluid is reached by the magnetic field of the coil in one end of the device. Two approaches were considered in this experiment: a parametric approach based on the Bingham, Bouc-Wen and Hyperbolic Tangent models and a non parametric approach based on a Neural Network model. The accuracy to reproduce the MR damper behavior is compared as well as some aspects related to performance are discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.582-585
• /
• 2001

InSb temperature dependent hall effect of multilayerd structures were investigated. According to variation of magnetic field measured hall coefficient, Hall mobility, carrier density and hall voltage. For the measurement of electrical properties of hall device, evaperated InSb thin film fabricated with series and parallel multilayers. We found that the XRD analysis of InSb thin film showed good properties at 200$^{\circ}C$, 60 minutes. Resistance of ohmic contact increased linearly due to increasing current. Some of device fabrication technique and analysis of Hall effect were discussed.

• Progress in Superconductivity
• /
• 제6권1호
• /
• pp.32-36
• /
• 2004

To investigate the influence of strip width and inter-strip separation on the ac loss, arrays of parallel strips with different widths and separations were prepared. Studies on the hysteresis-loss characteristics of multifilamentary YBCO films were performed. The local magnetic field due to magnetization currents is measured by a scanning Hall probe microscope. Based on these results a conceptual design for a low loss YBCO coated conductor is suggested.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.451-454
• /
• 1989

A DC thermal plasma generation system for both LPPS and APPS was designed and its characteristics was analysed. Discharge experiments for 60 conical and cylindrical type anode nozzle were conducted and the results were compaerd each other. The flow dependence and the electrode gap dependence were precisely explained and especially voltage jump phenomena under the existance of the parallel magnetic field was studid.

• Journal of Mechanical Science and Technology
• /
• 제19권11호
• /
• pp.2053-2060
• /
• 2005

The unsteady Couette flow of an electrically conducting, V1SCOUS, incompressible fluid bounded by two parallel non-conducting porous plates is studied with heat transfer taking the Hall effect into consideration. An external uniform magnetic field and a uniform suction and injection are applied perpendicular to the plates while the fluid motion is subjected to an exponential decaying pressure gradient. The two plates are kept at different but constant temperatures while the Joule and viscous dissipations are included in the energy equation. The effect of the ion slip and the uniform suction and injection on both the velocity and temperature distributions is examined.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.332-334
• /
• 2008

The matrix-type superconducting fault current limiter (SFCL) using YBCO thin film consists of the trigger and current-limiting parts. We fabricated the matrix-type SFCL with the integrated current limiting modules. we carried out the experiment of matrix-type SFCL with the integrated current limiting modules connected in series or parallel. We saw current characteristics due to ratio of change the shunt resistance and turns. We confirmed that the difference of critical current between superconducting units was decreased by increment of current flowing into the reactor which applied the magnetic field into the superconducting units..