• 대한기계학회논문집B
• /
• 제36권9호
• /
• pp.885-894
• /
• 2012

마이크로채널 메탄 수증기 개질 반응기의 열 및 물질 전달 특성을 이해하기 위한 수치해석 연구를 수행하였다. Rh-촉매의 메탄 수증기 개질 반응과 Pt-촉매의 메탄 연소 반응을 함께 모델링하였다. 화학 반응의 반응 속도를 해석 모델에 적용하였다. 접촉시간, 평행류 대향류 등 유동 패턴, 채널 크기 등이 개질 성능과 온도 분포에 미치는 영향을 관찰하였다. 평행류와 대향류는 서로 반대되는 온도 분포를 갖게 되고, 그로 인해 서로 다른 반응 속도와 화학종 몰분율을 나타낸다. 접촉시간이 짧아지고 채널 크기가 증가할수록 촉매층과 혼합물 유동 사이의 물질 전달이 제한되어 개질 성능은 감소하게 된다.

• 한국인터넷방송통신학회논문지
• /
• 제12권4호
• /
• pp.111-118
• /
• 2012

다양한 방송사와 서로 다른 CP(Contents Provider)가 분산되어 있는 Data Center서버에서 VOD 서비스를 하고자 할 때, 서로 다른 CP 플랫폼들이 고화질 HD, 3DTV 비디오 등의 영상파일을 교환하기 위해 고성능 네트워크를 통하여 빠르게 전송할 수 있는 망을 빠르게 구성해야 한다. 본 논문은 Public망의 QoS와 보안성을 보완하는 선택적인 암호화 방안을 이용하여, 고속의 안전한 VPN(Virtual Privatr Network)을 생성하고 콘텐츠를 고속으로 대용량 영상파일을 전송하는 프로토콜을 제안한다. End to End의 Device가 대용량의 영상파일을 Parallel 전송으로 가용한 자원을 최대한 사용하면서 안전한 콘텐츠 전송이 가능한 고성능의 VPN을 구성하는 모델을 제안한다.

• 조명전기설비학회논문지
• /
• 제22권5호
• /
• pp.31-40
• /
• 2008

최근 FPD 산업에서 물류이송장비의 전원장치로 비접촉 전원장치에 관한 연구가 활발히 진행되고 있다. 양산 라인에 적용되고 있는 물류장비의 비접촉 전원장치는 주로 직선구간을 왕복하고, 이송대차가 한 대인 경우에 적용하고 있다. 그러나 곡선 구간과 이송대차가 다수인 경우의 물류이송장비에는 적합하지 않다. 따라서 본 논문은 직 곡선 구간이 혼용되어진 구조이고, 이송대차가 한 대 이상으로 구동되는 물류이송장비의 비접촉 전원장치 시작품에 적용하였고, 적용된 비접촉 전원장치의 회로 구조는 풀 브릿지 구조를 갖는 직 병렬 공진 DC/DC 컨버터 회로로 하여 회로해석, 제어방법, 특성평가, 실험을 통한 적용 가능성에 대한 연구를 행하였다. 또한 비접촉 전원장치의 전체 제어는 1차측 전원공급장치에 일정한 공진전류를 제어하기 위해 듀티 제어를 사용하였고, 2차측 전원공급장치의 출력전압을 일정하게 유지하기 위해 다수의 이송대차가 자체 제어를 하도록 구성하였다. 실제 2대의 이송대차를 제작하여 직 곡선 구간을 구성하고, 물류이송장비를 운용하여 양호한 특성으로 적용 가능함을 알 수 있었다.

• 한국항행학회논문지
• /
• 제27권1호
• /
• pp.63-70
• /
• 2023

본 연구는 선박 추진 축계의 무선 센서 시스템(WSS) 응용을 위한 용량성 무선 전력 전송(C-WPT) 시스템을 제시한다. 커플링 커패시터 양쪽의 단일 Q 팩터 및 회로에서 무효 전력제거를 위해 양면 LCLC 컨버터 및 변압기 토폴로지가샤프트에서 WSS용 회전식 C-WPT 시스템을 구동하도록 설계되었습니다. 170pF의 용량을 갖는 병렬 연결된 평행판 회전 커패시터가 설회전축의 C-WPT 시스템용으로 설계 및 구현된다. 실험 결과 C-WPT 시스템은 3mm 거리 및 1 MHz 작동 주파수에서 7.8 W 출력 전력으로 66.67 %의 전송 효율을 달성했다. 따라서 제작된 C-WPT 시스템은 회전축의 WSS에 전원을 공급할 수 있음을 증명하였다.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.165-173
• /
• 1997

The present study investigates heat/mass transfer for flow through perforated plates for application to combustor wall and turbine blade film cooling. The experiments are conducted for hole length to diameter ratios of 0.68 to 1.5, for hole pitch-to-diameter ratios of 1.5 and 3.0, for gap distance between two parallel perforated plates of 1 to 3 hole diameters, and for Reynolds numbers of 60 to 13, 700. Local heat/mass transfer coefficients near and inside the cooling holes are obtained using a naphthalene sublimation technique. Detailed knowledge of the local transfer coefficients is essential to analyze thermal stress in turbine components. The results indicate that the heat/mass transfer coefficients inside the hole surface vary significantly due to flow separation and reattachment. The transfer coefficient near the reattachment point is about four and half times that for a fully developed circular tube flow. The heat/mass transfer coefficient on the leeward surface has the same order as that on the windward surface because of a strong recirculation flow between neighboring jets from the array of holes. For flow through two perforated plate layers, the transfer coefficients on the target surface (windward surface of the second wall) affected by the gap spacing are approximately three to four times higher than that with a single layer.

• 대한기계학회논문집B
• /
• 제26권1호
• /
• pp.150-158
• /
• 2002

Local heat/mass transfer and friction loss in a square duct roughened with various types of continuous and discrete rib turbulators are investigated. The combined effects of the gap flows of the discrete ribs and the secondary flows are examined for the purpose of the reduction of thermally weak regions and the promotion of the uniformity of heat/mass transfer distributions as well as the ;augmentation of average heat/mass transfer. The rib-to-rib pitch to the rib height ratio (p/e) of 8 and the rib angles of 90° and 60° are selected with e/D$\_$h/=0.08. The vortical structure of the secondary flows induced by the parallel angled arrays are quite distinct from that induced by the cross angled arrays. This distinction influences on heat/mass transfer and friction loss in all the tested cases. The gap flows of the discrete ribs reduce the strength of the secondary flows but promote local turbulence and flow mixing. Consequently, the angled discrete ribs with the small gaps provide a more uniform heat/mass transfer distribution sustaining high average heat/mass transfer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2211-2216
• /
• 2007

Liquefied gas vaporizer means machine to vaporize the liquefied gas as liquid nitrogen($LN_2$), liquefied natural gas(LNG), liquid oxygen($LO_2$) etc. In the air type vaporizer, the frozen dew is also created by temperature drop (below 273 K) on vaporizer surface. This problem increases as the time progresses and humidity increases. In addition, the frozen dew gradually becomes frost deposit consequently, heat transfer through vaporizer decreases because frost deposit form adiabatic sheet. Because of this reason, recent vaporizer system is installed as parallel type, this vaporizer system needs more expensive installation costs and more space. This paper was investigated on the heat transfer characteristics of liquefied gas vaporizer with super low temperature and this paper was carried out the numerical about air heating vaporizer with super low temperature. The numerical analysis on the heat transfer was studied on the effect of geometric parameters of the vaporizer, which are length 1000 mm of 4fin75le type vaporizer. 4fin75le means number of fin is 4 and height of fin is 75 mm.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 추계학술대회 논문집
• /
• pp.101-109
• /
• 2010

This paper reports active control of clamped beams using acceleration feedback controllers (AF). The equations of motion of clamped beam under force and moment pairs were derived and the equations of AF controllers were formulated. The effect of the parameters - gain and damping ratio - of the AF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the AF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies. The increase of the damping ratio of the AF controller leads to decrease the magnitude of the open loop transfer function and modifies its phase characteristics to be more stable. Three AF controllers connected in parallel were then proposed. Each AF controller is tuned at the $2^{nd}$, $3^{rd}$ and $4^{th}$ modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 3 modes can be obtained.

• 대한기계학회논문집A
• /
• 제28권6호
• /
• pp.774-782
• /
• 2004

This article presents a numerical and experimental investigation for the single-phase forced laminar convective heat transfer through arrays of micro-channels in micro heat exchangers to be used for cooling power-intensive semiconductor packages, especially the stacked multi-chip modules. In the numerical analysis, a parametric study was carried out for the parameters affecting the efficiency of heat transfer in the flow of coolants through parallel rectangular micro-channels. In the experimental study, the cooling performance of the micro heat exchanger was tested on prototypes of stacked multi-chip modules with difference channel dimensions. The simulation results and the experiment data were acceptably accordant within a wide range of design variations, suggesting the numerical procedure as a useful method for designing the cooling mechanism in stacked multi-chip packages and similar electronic applications.

• 전력전자학회논문지
• /
• 제19권5호
• /
• pp.470-474
• /
• 2014

This study proposes an improved synchronization control scheme for a low-cost 400Hz power supply for a no-break power transfer system. In the case of aircraft applications, the 400Hz power supply called ground power units is accepted and used as the external electrical power system during stopovers on ground. A momentary break in the supply occurs when shifting from one power source to another. To allow shifting without a break in the supply, the two power sources are momentarily connected in parallel. The proposed synchronization control is achieved by connecting an existing synchronization bus to the voltage zero-crossing signal of a generator power with discrete logic ICs and analog circuits. Therefore, unlike expensive controllers, such as DSP and CAN, the proposed control scheme is rather simple and may decrease operational cost. The practical feasibility of the proposed control scheme is proven by experimental results.