• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.67-67
• /
• 2000

In this paper, a hybrid type fuzzy controller is proposed to maintain molten steel level stable and reliable manner in high speed continuous casting regardless of various disturbances such as casting speed change, tundish weight variation, 치ogging/undoning of SEN(Submerged Entry Nozzle), periodic bulgings, etc. To accomplish this purpose, hardware filter and software filer are carefully designed to eliminate high frequency noise and to smooth input signals from harsh environments. In order to minimize the molten steel level variations from various disturbances the controller uses hybrid type control term: fuzzy logic term, proportional term, differential term and nonlinear feedback compensation tenn. The proposed controller is applied tn commercial mini-mill plant and shows considerable improvement in minimizing the molten steel variation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 제7회 압연 심포지엄
• /
• pp.111-114
• /
• 2009

Production of rolled steel has been growing partly supported by the advancement of rolls and rolling mills. Aiming at the further improvement in roll performance, various new techniques such as centrifugal casting, double poured casting cast steel, special build-up making, etc. have been introduced in the field of roll manufacture in these several years. The present paper describes the development of horizontal cast rolls(sleeve and indefinite chilled roll) made by Hyundai Steel and the results of mill tests. The developed roils are contributing the improvement of final products.

• 한국주조공학회지
• /
• 제20권1호
• /
• pp.3-12
• /
• 2000

The lead content of drinking water has been restricted to less than 15 ppb by Environmental Protection Agency (EPA) in USA. This has led to extensive research and development work at the Materials Technology Laboratory (MTL) of CANMET, a Canadian Government research laboratory, on the development of low-lead and lead-free copper alloys for plumbing applications. Attentionhas also been focused on the environmentally friendly and energy efficient permanent mold casting process to minimize the disposal of foundry sand contaminated by lead due to the use of leaded alloys in the non-ferrous foundries. A new series of alloys called SeBiLOY contaning Bi and Se been introduced to replace lead in the leaded alloys. This paper addresses some important casting characteristics such as fluidity, hot tear resistance, mechanical properties and microstructure of lead-free alloys such as SeBiLOY III and low-lead alloys such as silicon brass, silicon bronze and yellow brass in gravity permanent mold casting.

• 한국안전학회지
• /
• 제26권4호
• /
• pp.27-33
• /
• 2011

Forensic Engineering is the area covering the investigation of products, structures that fail to perform or do not function as intended, causing personal injury or damage to property. To investigate explosion accident of the centrifugal casting machine in terms of the forensic engineering, in this paper, the computing simulation using ADINA FSI has performed to investigate that the effect of the Check-Pin fracture by the flow phenomena and molten metal weight and the mechanical properties test of the accident Check-Pin has performed using the instrumented indentation technique. Through these studies, the safety accident that may occur in centrifugal casting machine can be minimized by performing specialized and systematic investigation of the accident cause in terms of the forensic engineering.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.203-210
• /
• 2006

This paper focuses on the development of RT technology suitable for manufacturing a small quantity of metal prototype of a precise part from an RP master. Dimensional accuracy and surface roughness are evaluated from Thermojet part of a 3D printer, and effective post-processing method is introduced. Investment casting is done using a prototype built from 3D printer as a wax pattern. Ceramic shell investment casting technique is developed to build a prototype with materials mostly wanted. Also, experimental result shows this research is very useful in manufacturing of a small quantity of functional part or a test part of a specific material.

• 한국주조공학회지
• /
• 제32권2호
• /
• pp.65-74
• /
• 2012

In this paper, we present the results of our studies on optimal die design towards development of a vacuum die casting process to fabricate fuel cell bipolar plate with micro-channel array. Cavity and overflow shape is designed by computational filling analysis of MAGMA soft. Optimal die design consists of seven overflows at the end of cavity and three overflows at each side wall of cavity. The molten metal that passed the gate and reached the side wall flowed into the side overflow, no turbulent flow occurred, and the filling behavior and velocity distribution were uniform. In addition, partially solidified molten metal passing through the channel was perfectly eliminated by overflow without back-flow. When vacuum pressure, injection speed of low and high region was 300 mbar, 0.3 m/s and 2.5 m/s respectively with Silafont 36 die casting alloy, sound sample without casting defects was obtained. The experimental results are nearly consistent with simulation results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.138-143
• /
• 1998

The continuous casting process has been adopted increasingly in recent years to save both energy and labor. It has experienced a rapid development in the production of semi-finished steel products, replacing the conventional route of ingot casting plus rolling. To achieve this good merit, however, more studies about a heat transfer mechanism between roll and slab are needed. So this paper shows the results of the deformation behavior of steel cast slabs, which are about the solidification and heat transfer. This study is used to prevent internal cracks of a slab in a bending and unbending zone. The value of moving strand shell bulging between two supporting rollers under ferrostatic pressure and slab-self weight has been computed in terms of creep and elastic-plasticity. The high strand distributions in solidified shell undergoes a series of bulging are calculated with boundary condition a very closed to continuous steel cast slabs productions.

• 한국주조공학회지
• /
• 제4권4호
• /
• pp.5-13
• /
• 1984

This paper is presented for showing the effect of cooling rate on dendrite arm spacing, correlated with the chilling power of molding materials (conventional plaster, foamed plaster, silica sand) and section thickness, and also showing relationship between dendrite arm spacing and mechanical properties for an aluminum - 8.6 percent silicon - 3.6 percent copper alloy. Local solidification time $(t_f)$ and secondary dendrite arm spacing (d) could be varied widely in accordance with the molding materials and casting thickness, and the following relationship is obtained: $d=9.4t_f\;^{0.31}$ A good correlation between dendrite arm spacing and mechanical properties such as ultimate tensile strength, yield strength, hardness was found, that is, mechanical properties decreased in a linear manner with increase in log of secondary dendrite arm spacing. Ultimate tensile strength in conventional plaster mold casting decreased by 15 percent comparing with the sand casting, where as in foamed plaster mold casting, it decreased by 30 percent comparing with the sand casting. From those results, it has been verified that DAS might be the most representative parameter for predicting mechanical properties varing with the different cooling condition.

• 수산해양기술연구
• /
• 제17권2호
• /
• pp.85-91
• /
• 1981

평판 강괴를 연속적으로 주조할 경우에 초기주조 상태에서 Mold 내부의 Support bar 및 용강자중, 주조속도, 용강두께, 이를 지지하는 제어 Roller, 유압기구, 구동 Motor, 그리고 주조조직의 응고 등이 용강의 인발력을 유도하는 Pinch Roller와의 사이에서 동력학적 부평형을 일으켜 Slip 현상을 초래하므로 본 논문에서는 이상의 제요인들을 근거로 Slip 현상을 규명하는 식을 유도하고 강괴의 주조속도, 비중량, 두께의 변화에 대한 Slip Force 거동을 규명하였다. 그 결과 1. 본 논문의 해석식에 의하여 평판강괴 연속주조용 Pinch Roller의 적정압을 설계할 수 있다. 2. 비중량은 순수히 자중만 증가시키는 요인이며 Slip Force는 주조속도변화에 대해서 포물선적으로 증가한다. 3. 주조두께 및 비중량의 변화에 대한 Slip Force는 이에 비례하여 증가하나 특히 두께의 값이 소폭보다 대폭에서 그 변화 값이 크게 나타났다.

• 대한의용생체공학회:의공학회지
• /
• 제26권1호
• /
• pp.23-30
• /
• 2005

3D virtual endoscopy has been used as an alternative non-invasive procedure for visualization of hollow organs. However, due to computational complexity, this is a time-consuming procedure. In this paper, we propose a fast volume rendering algorithm based on perspective ray casting for virtual endoscopy. As a pre-processing step, the algorithm divides a volume into hierarchical blocks and classifies them into opaque or transparent blocks. Then, in the first step, we perform ray casting only for sub-sampled pixels on the image plane, and determine their pixel values and depth information. In the next step, by reducing the sub-sampling factor by half, we repeat ray casting for newly added pixels, and their pixel values and depth information are determined. Here, the previously obtained depth information is utilized to reduce the processing time. This step is recursively performed until a full-size rendering image is acquired. Experiments conducted on a PC show that the proposed algorithm can reduce the rendering time by 70- 80% for bronchus and colon endoscopy, compared with the brute-force ray casting scheme. Using the proposed algorithm, interactive volume rendering becomes more realizable in a PC environment without any specific hardware.