• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.235-240
• /
• 1998

The inlet pressure build-up at the leading edge of bearings and its effects on the static performances are investigated theoretically. The performance analyses of air-lubricated tilting pad bearings are carried out considering the inlet pressure which is obtained by means of momentum conservation method. The results show that inlet pressure is above atmosphere pressure in front of leading edge of tilting pad bearing and there is a significant influence of the inlet pressure on the performance of bearings.

• Tribology and Lubricants
• /
• v.17 no.2
• /
• pp.116-123
• /
• 2001

A theoretical analysis has been undertaken to show the influence of bearing geometry on the steady state characteristics of air lubricated spherical tilting pad bearings. The geometry variations considered are the number of pads, the eccentricity ratio, the direction of load, and the preloading. Dynamic characteristic equations are derived with pad assembly method.

• Tribology and Lubricants
• /
• v.31 no.6
• /
• pp.294-301
• /
• 2015

In this paper, we predict the rotordynamic force coefficients of tilting pad journal bearings (TPJBs) with rocker-back pivots, and we compare the predictions to recently published predictions and test data. The present TPJB model considers the rocker-back pivot stiffness calculated based on the Hertzian contact-stress theory, which is nonlinear with the application of a force . For the five-pad TPJB in load-between-pad and load-on-pad configurations, the predictions show the pressure- and film-thickness distributions, the deflection and stiffness of the individual pivots, and bearing stiffness and damping coefficients. The minimum film thickness and peak pressure occur at the bottom pad on which the applied load is directed. Because of the preload, the pres- sure is positive even at the upper pad in the opposite direction to the applied load. The pivot deflection and stiff- ness are maximum at the bottom pad that receives the heaviest pressure load. The predicted stiffness coefficients increase as the static load and rotor speed increase, while the damping coefficients decrease as the rotor speed increases, but increase as the static load increases. In general, the predicted stiffness coefficients agree well with the test data. The predicted damping coefficients overestimate the test data, particularly for large static loads. In general, the current predictive model considering the pivot stiffness improves the accuracy of the rotordynamic performance compared to previously reported models.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.362-365
• /
• 2005

Currently Chemical Mechanical Planarization (CMP) has become an essential step in the overall semiconductor wafer fabrication technology. Especially the CMP pad conditioner, one of the diamond tools, is required to have strong diamond retention. Strong cohesion between diamond grits and metal matrix prevents macro scratch on the wafer. If diamond retention is weak, the diamond will be pulled out of metal matrix. The pulled diamond grits are causative of macro scratch on wafer during CMP process. Firstly, some results will be reported of cohesion between diamond grits and metal matrix on the diamond tools prepared by three different manufacturing methods. A measuring instrument with sharp cemented carbide connected with a push-pull gauge was manufactured to measure the cohesion between diamond grits and metal matrix. The retention force of brazed diamond tool was stronger than the others. The retention force was also increased in proportion to the contact area of diamond grits and metal matrix. The brazed diamond tool has a strong chemical combination of the interlayer composed of chrome in metal matrix and carbon which enhance the interfacial cohesion strength between diamond grits and metal matrix. Secondly, we measured real-time data of the coefficient of friction and the pad wear rate by using CMP tester (CETR, CP-4). CMP pad conditioner samples were manufactured by brazed, electro-plated and sintered methods. The coefficient of friction and the pad wear rate were shown differently according to the arranged diamond patterns. Consequently, the coefficient of friction is increased according as the space between diamonds is increased or the concentration of diamonds is decreased. The pad wear rate is increased according as the degree of diamond protrusion is increased.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2D
• /
• pp.299-309
• /
• 2006

Railway noise and vibration has been recognized as major problems with the speed-up of rolling stock. As a kind of solution to these problems, the decrease of stiffness of track pad have been tried. However, in this case, overturning of rail due to lateral force should be considered because it can have effect on the safety of running train. Therefore, above two things - decrease of stiffness of track pad and overturning of rail due to lateral force - should be considered simultaneously for the appropriate determination of spring coefficient of track pad. With this viewpoint, minimum spring coefficient of track pad is estimated through the comparison between the theoretical relationship about the overturning of rail and 3-dimensional FE analysis result. Two kinds of Lateral force and wheel load are used as input loads. Extracted values from the conventional estimation formula and the Shinkansen design loads are used. It is found that the overturning of rail changes corresponding to the change of the stiffness of track pad and the ratio of lateral force to wheel load. Moreover, it is found that the analysis model can have influence on the results. Through these procedure, minimum spring coefficient of track pad is estimated.

• Tribology and Lubricants
• /
• v.12 no.1
• /
• pp.29-35
• /
• 1996

The static and dynamic stability analysis of air-lubriceted tilting pad journal bearing which considers tilting effect of each pad and preload but neglects pad inertia were performed. And these characteristic analysis were performed with elasticity effect too. A direct numerical method is used in calculating the static characteristics such as load carrying capacity, firction force and perturbation method is used for calculation of dynamic characteristics. The stability analysis was performed with the variation of bearing number, eccentricity ratio and attitude angle considering pad elasticity effect.

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.2 s.15
• /
• pp.43-49
• /
• 2002

In this paper, the steady-state performances analysis of a tilting pad gas bearing(TPGB) we analyzed by using finite element method for compressible Reynolds' equation. TPGB is used in a high-expansion-ratio expander running at a speed of 230,000 rpm. In order to solve the nonlinear finite element equations, the Newton-Raphson method is applied. The variations of the loading capacity, friction force and tilting angle of a single pad v.s. eccentricity direction of eccentricity and bearing number are investigated. The condition for the equilibrium of a pad, which is important for safe working of the bearing, is stated. The performances of the three pad bearing such as loading capacity, friction moment are predicted.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1628-1636
• /
• 2008

Construction of concrete slab track is trending to increase gradually in national and international for reduction in track maintenance cost and secure of ride comfort. But elastic pad becomes superannuated due to repeated train operation. After all, it brings change of pad stiffness and it could directly act on track and bridge as load transmission and impact force. In this study, we carried out laboratory test changing pad stiffness after making a model of 15m bridge and laying concrete slab track. Also, we carried out static and dynamic behaviors test(stress, natural frequency, damping ratio, vibrational acceleration, deflection) of bridge and track and experimentally analyzed them by change of elastic pad stiffness on rail fastener.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.622-625
• /
• 2004

The CMP monitoring system was newly developed by the aid of friction force measurement, resulting from installation of piezoelectric quartz sensor on R&D polisher. The correlation between friction and CMP results was investigated in terms of tribological aspects by using the monitoring system. Various friction signals were monitored and analyzed by the change of experimental conditions such as pressure, velocity, pad and slurry. First of all, the lubrication regimes were classified with Sommerfeld Number through measuring coefficient of friction in ILD CMP. And then, the removal mechanism of abrasives could be understood through the correlation with removal rate and coefficient of friction. Especially, the amount of material removal per unit sliding distance is directly proportional to the friction force. The uniformity of CMP performances was also deteriorated as coefficient of friction increased.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.463-468
• /
• 2002

This study investigates the variations of shear force, displacement, and fracture surface with the shear speed and the number of reflows. The experimental data of shear tests indicate that the shear force increases as increasing the number of reflows and the shear speed due to the formation of a kind of intermetallic compound, Ni$_3$Sn$_4$, on Au/Ni/Cu pad, and the work-hardening. However, general trends show that the shear force decreases due to increasing the thickness of the intermetallic compound over 4x reflow. It is observed that the intermetallic compound which is formed between solder and pad increases according to increasing the number of reflows, and the growth rate of the intermetallic compound at central region on the interface is faster than one at edge part. The general tendencies of shear force and displacement with different shear speeds are almost identical as an increase of the number of reflows.