• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.168-172
• /
• 1988

In order to prevent the PbO vaporization during calcination and to produce the powder of good sinterability, a coprecipitation method for preparing homogeneous Lead-Zirconate-Titanate (PZT) powder from aqueous salt solution is described. In this method, the PZT-ceramics show low calcining and sintering temperature, and they have good sintering and electronic properties.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.523-526
• /
• 2014

PZT($Pb(Zr_{0.53}Ti_{0.47})O_3$)/PVDF(poly vinylidene fluoride) nanofibers were prepared based on DMF (dimethylformamide) and acetone solvent by electrospinning. The optimum concentration of a PZT and PVDF composite solution for the formation of nanofibers was found by SEM (scanning electron microscopy) observations. XRD (X-ray diffraction) measurements indicated that the characteristics of PZT and PVDF coexisted. The effects of the PZT concentration on the tensile strength were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.331-332
• /
• 2006

Ag-ceramic composite materials were investigated as internal electrodes for multilayer ceramic actuators (MLCA). Ag-ceramic pastes were prepared by adding PZT-based ceramic powders to a Ag patse in a range of 0 to 50 wt.%. PZT/Ag-PZT multilayered laminates were fabricated by tape casting and fired at low temperatures below $950^{\circ}C$. The addition of ceramic into the Ag electrode resulted in a decrease in the thermal expansion mismatch between the electrode and the ceramic sheet. The maximum strain of PZT/Ag-PZT multilayered actuators were $9{\times}10^{-4}$ under an electric field of 2.5MV/m. In conclusion, Ag-PZT composite materials are efficient for low cost piezoelectric MLCAs.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.588-590
• /
• 1989

Charge sensitivity and its frequency response characteristics were measured in poled and aged lead zirconate titanate(PZT) ceramics prepared by sintering. Aged PZT has lower charge sensitivity and lower mounted resonance frequency than just poled PZT.

• Journal of Sensor Science and Technology
• /
• v.22 no.6
• /
• pp.400-403
• /
• 2013

The piezoelectric composite film of ferroelectric PZT ceramic ($PbZr_xTi_{1-x}O_3$) and polymer (PDMS, Polydimethylsiloxane) was prepared to improve the flexibility of piezoelectric material. The bar coating method was applied to fabricate flexible nanocomposite film with large surface area by low cost process. In the case of using metal electrode on the composite film, although there is no problem by bending process, the electrode is usually broken away from the film by stretching process. However, the well-attached, flexible CNT electrode on PZT/PDMS film improved flexibility, especially stretchability. PZT particles was usually settled down into polymer matrix due to gravity of the weighty particle, so to improve the dispersion of PZT powder in polymer matrix, small amount of additives (CNT powder, Carbon nanotube powder) was physically mixed with the matrix. By stretching the film, an output voltage of PZT(70 wt%)/PDMS with CNT (0.5 wt%) was measured.

• KSBB Journal
• /
• v.13 no.5
• /
• pp.477-482
• /
• 1998

A biosensor with PZT piezoelectric ceramic crystal was developed for the detection of formaldehyde gas. Poled PZT piezoelectric ceramic disk was made from ZrO2, TiO2 and Nb2O5, together with the addition of PbO and polyvinyl alcohol, through various processes of mixing, calcination drying, crushing, forming, sintering, polishing, ion coating and poling. Oscillator circuit of sensor was made of operational amplifier(AD811AN). Formaldehyde dehydrogenase was immobilized onto a piezoelectic ceramic crystal, together with the cofactors, reduced glutathione and nicotinamide adenine dinucleotide. The effect of flow rate on the sensitivity was determined by varing the flow rate of carrier gas from 24.7mL/min to 111.7mL/min through detector cell. The results indicated that as the flow rate was increased, the recovery rate was increased. And a significant increase in the sensitivity was observed in enhanced flow rate of carrier gas. Frequency difference(ΔF) of immobilized PZT piezoelectic disk increased proportionally to the concentration gas and reproduced to repeated exposures of formaldehyde gas(28ppm, Δ68Hz).

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.385-392
• /
• 2003

Sol-gel preparation technique using a chemical reaction of metal alkoxides has been widely used for the fabrication of various materials including ceramics. However, its mechanism has been studied till now because a number of chemical ways are possible from various alkoxides and additives. In this study, the mechanism of hydrolysis, condensation, and polymerization of alkoxides were investigated from the fabrication of lead-zirconate-titanate (PbZr$\_$x/Ti$\_$l-x/O$_3$; PZT) thin film that is used as various micro-actuator, transducer, and sensor because of its high electro-mechanical coupling factors and thermal stability. Furthermore, the fabrication process and characteristics of self-patternable PZT film using photosensitive stabilizer were studied in order to resolve the problem of physical damage and properties degradation during dry etching for device fabrication. Using an optimum condition to prepare the self-patternable PZT film, more than 5000 ${\AA}$ thick self-patternable PZT film could be fabricated by three times coating. The PZT film showed 28.4 ${\mu}$c/cm$^2$ of remnant polarization (Pr) and 37.0 kV/cm of coercive field (E$\_$c/).

• Journal of the Korean Ceramic Society
• /
• v.36 no.12
• /
• pp.1316-1321
• /
• 1999

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.6
• /
• pp.541-549
• /
• 2007

This work describes an investigation into the feasibility of using an acoustic emission (AE) technique to evaluate the integrity of a composite actuator with a PZT ceramic under electromechanical cyclic loading. AE characteristics have been analyzed in terms of the behavior of the AE count rate and signal waveform in association with the performance degradation of the composite actuator during the cyclic tests. The results showed that the fatigue cracking of the composite actuator with a PZT ceramic occurred only in the PZT ceramic layer, and that the performance degradation caused by the fatigue damage varied immensely depending on the existence of a protecting composite bottom layer. We confirmed the correlations between the fatigue damage mechanisms and AE signal types for the actuators that exhibited multiple modes of fatigue damage; transgranular micro damage, intergranular fatigue cracking, and breakdown by a short circuiting were related to a burst type signal showing a shortly rising and slowly decaying waveform with a comparably low voltage, a continuous type signal showing a gradual rising and slowly decaying waveform with a very high voltage and a burst and continuous type signal with a high voltage, respectively. Results from the present work showed that the evolution of fatigue damage in the composite actuator with a PZT ceramic can be nondestructively identified via in situ AE monitoring and microscopic observations.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.700-707
• /
• 2009

This paper described finite element analysis (FEA) for fabrication processes of PZT perform using ceramic injection molding (CIM). The viscosity and the PVT characteristics of the manufactured PZT feedstock were measured. The filling patterns, pressure and temperature distributions of the preform were analyzed with TIMON 3D packages during CIM process. The geometrical variables such as gate type, location, and base thickness of the preform were considered. Also the fabrication conditions of the preform were optimized during the entire CIM process. Based on the simulated results, the various good perform was easily fabricated with the CIM process.