• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.156-161
• /
• 1998

The purpose of this paper is to determine circuit parameters in the inverter part of the electronic dimming ballast for fluorescent lamps, that is adequate to use with the prevailing dimming controller IC. Firstly, the operating frequency characteristics are investigated by varying circuit parameters of electronic ballasts and are matched with the output characteristics of dimming ballast controller. Secondly, circuit parameter values are determined by using PSpice simulation and operating frequency characteristics. Finally its validity is verified from the electrical and light output characteristics on the prototype of the electronic dimming ballast.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.166-169
• /
• 1998

This paper represent about design of the controller for battery of fence with traffic controller for battery of fence with traffic auxiliary system for power supply using solar cell. Simulation is represents V-I and power characteristic by Pspice. This system is successfully operating with high clearness lights.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1212-1214
• /
• 2000

A new soft-switching PFC-Inverter for Induction Motor's operation with single phase or three phase medium size is proposed. In order to improve the power factor and the efficiency, in this paper, the ZVT topology in the conventional PFC-Inverter is adopted. So, the operation mode of the proposed ZVT PFC-inverter is analyzed and the optimum circuit is designed. At last, the PSPICE simulation and experiment results are presented in order to verify the validity of the proposed circuit.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1306-1308
• /
• 2000

A new ZVT PFC for using 3[KW] power amplifier is proposed. Generally, the single phase diode rectifier has been widely used in the SMPS of the conventional power amplifier. But this rectifier has occurred some problems which are the input power factor and current harmonics. To solve the above problems, in this paper, two topology is adopted. The one is the boost type PFC for improving the input power factor. The other is the ZVT resonant circuit for reducing the switching loss and stress. In this paper, the proposed topology is analyze designed to built the ZVT PFC for using 3[KW] power amplifier. In order to verify the circuit va finally, the PSPICE simulation and experiment results are presented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.2
• /
• pp.147-154
• /
• 1990

A 4:1 Time Division Multiplexer(MUX) had been designed in using GaAs Source Coupled FET Logic(SCFL), Designed Multiplexer uses a time division frequency divider and two stage of singnal combining 2:1 multiplexer. The performance of the multiplexer is verified by PSPICE simulation. Designed circuit operates up to 12.5Gbit/s with a power dissipation of 192mW. These performance are more advanced than other reported multiplexer in the speed and power dissipation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.8
• /
• pp.517-524
• /
• 2004

In this paper, a novel zero-voltage-switching(ZVS) resonant DC-DC converter is proposed. It is composed of two symmetrical active-clamped circuits, the converter can be achieve ZVS in each switches. Also, active clamp capacitor ratios($\alpha$) of proposed circuit can be reduce a peak stress of switching voltage for each main switch. Simulation results using Pspice 9.2 ver and $C^{++}$ characteristic analysis show a provement for the validity of theoretical analysis. The analysis of the proposed Current-Fed Push Pull type DC-DC converter is generally described by using normalized parameter, and achieved an evaluated characteristic values which is needed to design a circuit. We confirm a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1154-1156
• /
• 2003

본 논문은 IPM의 구동부, 과열, 과전류, 단락 및 제어부의 부족전압 제어하는 IC의 설계중 Over-Temperature protection기능에 대한 것으로서 기존의 온도센서나 과열검출 Tr을 사용하지 않고, 온도에 따른 MOSFET의 Rds(on)변화를 검출하여 과열을 방지하는 Direct Over Temperature protection기능을 PSpice를 이용하여 modelling하고 simulation 한 결과에 대해서 기술하였다.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.101-104
• /
• 2001

This paper represent about design of the controller for battery of a PE drum for power supply using PV Module. Simulation is represents V-I and power characteristic by Mathematica & Pspice 6.0 & Qnet 2.1. Finally, we composed of road surface-signpost system. This system is successfully operating with high clearness lights.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.694-697
• /
• 2001

A optimal soft switching technique for A/DC full bridge converter is proposed. variable soft switching single stage AC/DC full bridge converter with unit power factor are presented in this paper. Using soft switching, we can reduce a switching losses. As a result, achieving good power factor and achieving a good efficiency. We search a optimal soft switching technique in this paper and to verify the theoretical analysis of the presented AC/DC full bridge converter, a design example is given with its Pspice and Psim simulation and experimental results.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.237-240
• /
• 2006

In this paper, a new design using a simulation method was proposed. And to estimate its validity, various electronic and optical data were measured after making a 150[W] electronic ballast for high pressure sodium lamps. Using PSpice 9.1, the best solutions of various parameters such as the resonant frequency, the lamp output voltage, and the current of the electronic ballast were obtained. The power factor of the system was 99.8[%], the crest factor 1.44, the THD 4.99[%], and the weight 0.5[kg]. These are very good characteristics compared with a conventional HPS Lamp ballast.