• Journal of Advanced Marine Engineering and Technology
• /
• 제18권1호
• /
• pp.81-91
• /
• 1994

Combustion noise involved with chemical heat release and turbulent process in turbopropulsion systems, gasturbine, industrial furnaces and internal engines is indeed noisy. The experimental study reported in this paper is made to identify a dominant combustion noise in jet flames. Gaseous propane and kerosene fuel have been used with air as the oxidizer in a different jet combustion systems. Combustion and aerodynamic noise are studied through far field sound pressure measurements in an anechoic chamber. And also mean temperature and velocities and turbulent intensities of both isothermal and reacting flow fields were measured. It is shown that axial mean velocity of reacting flow fields is higher about 1 to 3m/sec than that of cold flow in a gaseous combustor. As the gaseous fuel flow rate increases, the acoustic power increases. But the sound pressure level for the spray flame decreases with increasing equivalence ratio. The influence of temperature in the combustion fields due to chemical heat release has been observed to be a dominant noise source in the spray flame. The spectra of combustion noise in gaseous propane and kerosene jet flame show a predominantly low frequency and a broadband nature as compared with the noise characteristics in an isothermal air jet.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2008년도 제39차 학술발표회
• /
• pp.109-110
• /
• 2008

본 연구에서는 신축성이 우수한 친수형 무공 PET필름을 사용해서, 소취성, 보온성 및 투습방수성이 우수한 신발용 소재를 개발하였다. 이상의 목적을 달성하기 위해서 최적 소재의 선정, PET필름의 특성평가, 최적 라미네이팅 공정조건 확립, 첨가제 선정 및 가공조건 확립 등에 대해서 실험고찰을 하였으며, 얻어진 주요 결과는 다음과 같다. (1) 신발의 갑피용 및 안창용 최적소재로서 경편직물을 선정하였으며, PET필름의 최적 요구특성은 내수성 9460mmH2O, 투습성 10,000g/m2/24hrs, 인장강도42kgf/cm2, 신도249% 였다. (2) Hot-melt 라미네이팅 공정에서의 투습방수성을 좌우하는 Dot roll No, Coating gap의 최적조건은 CP75(Engraved dot roll no), -0.2mm(Coating Unit gap) 였다. (3) EVA base polymer 및 기타 조제의 최적 배합비를 확립하고 이를 바탕으로 compound를 제조하여 Press로 molding하여 안창용 Sponge를 얻었다. (4) 안창 sponge 위에 점착된 knit 소재의 소취효과는 우수하였으며, 갑피용 투습방수 경편직물의 보온성도$15{\sim}20%$로 우수하였다.

• 콘크리트학회지
• /
• 제6권3호
• /
• pp.162-172
• /
• 1994

본 연구에서는 2번에 분리타설된 교량 슬래브의 휨 및 전단거동 특성에 대한 실험연구를 수행하였다. 분리타설된 슬래브의 거동은 구콘크리트의 표면상태, 다우웰 철근량 및 접착층의 부착강도에 의해 큰 영향을 받게 되므로, 본 연구에서는 이와 같은 변수를 변화시켜 실험을 수행하였다. 본 연구결과 초기균열이 발생할때까지는 콘크리트의 표면상태 및 다우웰 철근량에 따라 구조거동에 큰 차이를 보이지 않으나, 극한하중상태에 도달하면 구콘크리트의 표면상태가 양호하고 아크릴수지 처리와 다우웰 철근이 많을수록 분리타설된 슬래브는 일체로 거동하는 것으로 나타났다. 따라서, 본 연구결과는 앞으로 교량에서 2층으로 분리타설하는 철근콘크리트 슬래브의 설계를 위한 유용한 자료와 토대를 제시하고 있다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.243-246
• /
• 2003

평균 입도가 $100{\mu}m$인 $Fe_{36}Co_{62}Ge_2$ 합금 분말과 $10wt\%$의 페놀계 고분자 바인더, 그리고 평균 입도가 $1.36{\mu}m$인 WC 분말을 SPEX Mixer/Mill에 넣고 8시간동안 혼합한 후 $150^{\circ}C$에서 Warm press를 이용하여 0.9 ton 의 압력으로 2시간 동안 유지하였다. VSM을 사용하여 자기적 특성을 조사한 결과 WC의 첨가량이 증가할수록 포화자화값(Ms)는 $174\~128\;emu/g$로 감소하였다. 또한 스트레인게이지를 이용하여 자기변형을 측정하였다. WC의 분포를 알아보기 위해 전자현미경으로 복합체의 단면을 관찰하였다. WC의 함량이 $10\~30wt\%$로 증가할수록 밀도와 영률(Young's Modulus) 값이 각각 $5.15\~6.27\;g/cc,\;43.5\~93.6\;GPa$ 로 증가하였다. 특히 영률은 WC를 $30wt\%$로 첨가하였을 때의 값이 첨가하지 않았을 때보다 2배 이상 증가하였다. 그러나 비자성상의 첨가로 희석효과가 나타났으며 길이 방향으로의 자기변형값$(\lambda_{ll})$과 $d_{33}$의 경우 각각 $18\%$와 $20\%$ 정도가 감소되었다. 이러한 기계적 특성의 향상은 길이 10mm의 자기변형 복합체의 공진 주파수를 71 kHz 증가시키게 되며, 따라서 초음파 진동소자용으로서의 상업적 활용범위를 증가 가능성을 제시하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.231-235
• /
• 2000

Precision progressive die have used for above ten thousand pieces of lot size production part. In the field of design and making tool for press working, the progressive die for sheet metal (SPC, thickness : 2mm) is a specific division. In order to prevent the defects, the optimum design of the U-bending production part, strip layout, die design, die making and tryout etc. are necessary. They require analysis of many kinds of important factors, i.e. theory and practice of metal pres working and its phenomena, die structure, machining condition for die making, die materials, heat treatment of die component, know-how and so on. In this study, we designed and constructed a progressive die of multi-stage and performed try out. Out of these processes the die development could be taken for advance. Especially the result of tryout and its analysis become the characteristics of this paper (part 1 and part 2) that nothing might be ever seen before such as this type of research method on all the processes. In the part 2 of this study we treated die making and tryout mostly.

• 한국항해학회지
• /
• 제18권3호
• /
• pp.19-30
• /
• 1994

By use of the recent tropical cyclones' data in the Northwest Pacific Ocean, the occurrence frequency and region of typhoon as well as the features of the monthly mean track were analyzed. As the result of this study, (1) mean occurrence frequency of typhoon per year is 27.5, and 68% of total typhoons were formed in July to October and shown the highest frequency in August. (2) The ave-rage duration of typhoons is 8.5 days, and super typhoon which maximum sustained surface wind speeds is more than 130 knots occurs most frequently in October and November. (3) The highest frequency ap-pears around the Caroline, Mariana and Marshall Islands, and in wintertime, typhoon occurs in lower lati-tude comparing with those in summertime. (4) The typhoon track depends upon the distribution of pres-sure system and steering current in neighbouring areas. The mean track of typhoon can be classified into three types such as westward-moving type, northward-moving type and abnormally moving type. The west-ward-moving typhoons make landfall on the southern China by way of the South China Sea in June and July, on mid-part of China in August and September, and on Indo-china Peninsula in October and Novem-ber. The northward-moving typhoons approximately move on north~northwestward track to $20~30^{\circ}N$ from the occurrence region, then recurve to the East Sea through Korean Peninsula and Kyushu Island in June and July, to the Noth Pacific Ocean along the Japanese Islands in August and September and to the North Pacific Ocean through the seas far south off the Japan in October and November.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1062-1067
• /
• 2003

In this study, corrosion fatigue characteristics of CF8M and CF8A steel were investigated on the simulated PWR condition(Temp.:$316^{\circ}C$, Pres.: 15:MPa). To make the simulated PWR condition. the special test machine consisted of INSTRON, Autoclave, LOOP and Measurement system was developed. As ${\Delta}K$ is ranged from 11 to $20MPa{\sqrt{m}}$, Crack growth rate of PWR condition is faster than air condition. Above $20MPa{\sqrt{m}}$, the crack growth rate of PWR and air condition is similar. Corrosion fatigue characteristics regardless of the ferrite contents($10{\sim}25wt.%$) is not different. After the test, the fracture surface of specimens was examined. It was difficult to verify the fracture modes such as striation, intergranular crack and cleavage and so on. As the ferrite content of CF8M is increased, the more particles covered fracture surface were peeled.

• 대한의용생체공학회:의공학회지
• /
• 제13권2호
• /
• pp.155-164
• /
• 1992

Attachment and growth of mouse flbroblast cells on block copolypeptides were studied in the pres once or absence of serum proteins. Cells are rapidly attached to she polymer surface within 30 min regardless of substrate in the presence of serum. The number of flbroblast cells attached on the poly mer surface coated by collagen was larger than thats on the bare surface. Attachment of cells Is as a whole suppressed to a low level by the addltion of sodium azide in the absence of serum. Thls suE gests that the active attachment of cells requires the biological metabolism taking place on polymer substrates. In the presence of serum protein, flbroblast cells are more rapidly grown on the bolck co polymer consisting of poly(T-benzyl L-glutamate) (PBLG) and polyoxypropylene(POP) than on other block copolymers. These results were in agreement wish the data obatlned by an Inverted ml croscope.

• 한국수산과학회지
• /
• 제23권3호
• /
• pp.215-224
• /
• 1990

포화상태인 물질의 역학적, 수리학적 거동을 연구할 수 있는 유한요소법적 수치해석모델을 개발하여 부산 남항 인근해역의 미고결 퇴적물의 거동을 분석하였다. 하중재하에 의한 상부세립 퇴적물의 역학적 변형은 공극수의 확산에 따른 공극수압의 수리학적 변화에 크게 영향을 받는 것으로 나타났다. 하중이 일정지역에 편재되어 있을 경우 포아송효과 및 과잉공극수압의 영향에 의해 하중을 직접 받지 않는 표층부분이 융기되며, 하중경계지역에서 멀어질수록 점근적으로 증가한다. 세립점토층에 비해 높은 투수성을 갖는 하부 모래층은 공극수확산의 통로역할을 하여 과잉공극수압의 소멸을 촉진시키며, 결과적으로 상부점토층 변형의 시간적 변화에도 영향을 끼친다.

• Elastomers and Composites
• /
• 제33권1호
• /
• pp.37-43
• /
• 1998

The permeation of gas through polymer membrane at temperatures above its glass transition, generally occurs by a solution-diffusion mechanism. This mechanism is performed by the affinity difference between polymeric materials and gas molecules, and various technologies, such as copolymerization, impregnation and so on, have been researched to improve the affinity of polymeric material for the gases. In this study, permeability and selectivity for some gases were obtained from steady-state rates of gas permeation through silicone rubber membrane which is prepared by supercritical fluid extraction method. The permeability was measured by the volumetric method proposed by Barrer. Permeability was increased generally with temperature and permeation pressure. Silicone rubber membrane shows a higher permeability to $CO_2$ than to $O_2$, $N_2$. This results probably reflect the relatively high solubility of CO_2 in silicone rubber membrane, which is due to the affinity of $CO_2$ molecules. Since separation powers of $CO_2/N_2$, $CO_2/O_2$ were more than 200, and 100, respectively, it is able to separate $CO_2$ from the air, and the optimum temperature and pres-sure was 328.15 K, 60 cmHg respectively. In future, it is possible that the silicone rubber membrane can be used for separation or concentration of $CO_2$ through experiment for mixed gas separation.