• Journal of the Korean Wood Science and Technology
• /
• v.16 no.2
• /
• pp.1-41
• /
• 1988

For the purpose of utilizing the sawdust having poor combining properties as board raw material and resulting in dimensional instability of board, polypropylene chip (abbreviated below as PP chip) or oriented PP thread was combined with sawdust particle from white meranti(Shorea sp.). The PP chip was prepared from PP thread in length of 0.25, 0.5, 1.0 and 1.5 cm for conventional blending application. Thereafter, the PP chip cut as above was combined with the sawdust particle by 3, 6, 9, 12 and 15% on the weight basis of board. Oriented PP threads were aligned with spacing of 0.5, 1.0 and 1.5cm along transverse direction of board. The physical and mechanical properties on one, two and three layer boards manufactured with the above combining conditions were investigated. The conclusions obtained at this study were summarized as follows: 1. In thickness swelling, all one layer boards combined with PP chips showed lower values than control sawdustboard, and gradually clear decreasing tendendy with the increase of PP chip composition. Two layer board showed higher swelling value than one layer board, but the majority of boards lower values than control sawdustboard. All three layer boards showed lower swelling values than control sawdustboard. 2. In the PP chip and oriented thread combining board, the swelling values of boards combining 0.5cm spacing oriented thread with 1.0 or 1.5cm long PP chip in 12 and 15% by board weight were much lower than the lowest of one or three layer. 3. In specific gravity of 0.51, modulus of rupture of one layer board combined with 3% PP chip showed higher value than control sawdustboard. However, moduli of rupture of the boards with every PP chip composition did not exceed 80kgf/cm2, the low limit value of type 100 board, Korean Industrial Standard KS F 3104 Particleboards. Moduli of rupture of 6%, 1.5cm-long and 3% PP chip combined boards in specific gravity of 0.63 as well as PP chip combined board in specific gravity of 0.72 exceeded 80kgf/$cm^2$ on KS F 3104. Two layer boards combined with every PI' chip composition showed lower values than control sawdustboard and one layer board. Three layer boards combined with.1.5cm long PP chip in 3, 6 and 9% combination level showed higher values than control sawdustboard, and exceeded 80kgf/$cm^2$ on KS F 3104. 4. In modulus of rupture of PP thread oriented sawdustboard, 0.5cm spacing oriented board showed the highest value, and 1.0 and 1.5cm spacing oriented boards lower values than the 0.5cm. However, all PP thread oriented sawdustboards showed higher values than control saw-dustboard. 5. Moduli of rupture in the majority of PP chip and oriented thread combining boards were higher than 80kgf/$cm^2$ on KS F 3104. Moduli of rupture in the boards combining longer PP chip with narrower 0.5cm spacing oriented thread showed high values. In accordance with the spacing increase of oriented thread, moduli of rupture in the PP chip and oriented thread combining boards showed increasing tendency compared with oriented sawdustboard. 6. Moduli of elasticity in one, two and three layer boards were lower than those of control sawdustboard, however, moduli of elasticity of oriented sawdustboards with 0.5, 1.0 and 1.5cm spacing increased 20, 18 and 10% compared with control sawdustboard, respectively. 7. Moduli of elasticity in the majority of PP chip and oriented thread combining boards in 0.5, 1.0 and 1.5cm oriented spacing showed much higher values than control sawdustboard. On the whole, moduli of elasticity in the oriented boards combined with 9% or less combination level and 0.5cm or more length of PP chip showed higher values than oriented sawdustboard. The increasing effect on modulus of elasticity was shown by the PP chip composition in oriented board with narrow spacing. 8. Internal bond strengths of all one layer PP chip combined boards showed lower values than control sawdust board, however, the PP chip combined boards in specific gravity of 0.63 and 0.72 exceeded 1.5kgf/$cm^2$, the low limit value of type 100 board and 3kgf/$cm^2$, type 200 board on KS F 3104, respectively. And also most of all two, three layer-and oriented boards exceeded 3kgf/$cm^2$ on KS F. 9. In general, screw holding strength of one layer board combined with PP chip showed lower value than control sawdustboard, however, that of two or three layer board combined with PP chip did no decreased tendency, and even screw holding strength with the increase of PP chip composition. In the PP chip and oriented PP thread combining boards, most of the boards showed higher values than control sawdustboard in 9% or less PP chip composition.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.2
• /
• pp.46-55
• /
• 2008

This study assesses the formaldehyde and TVOC emissions from bio-composites with attached fancy veneer manufactured using wood flour and polypropylene (PP) measured using the Field and Laboratory Emission Cell (FLEC) method and 20 L small chamber method. To determine and compare the effects of the adhesive, samples were prepared with different manufacturing methods. In the FLEC result, the formaldehyde emission level of the bio-composites with attached veneer by hot-press was the lowest than pure bio-composite and bio-composite attached veneer using adhesive. The TVOC emission levels are similar to the formaldehyde emission. The TVOC emission level is very low in all of the samples except fancy veneer that is attached with bio-composites using adhesive. The TVOC emission varies depending on how attaching fancy veneer. The results of the 20 L small chamber method were very similar to those obtained with the FLEC, but the correlation was not perfect. However, the FLEC method requires a shorter time than the 20 L small chamber method to measure the formaldehyde and TVOC emissions. The internal bonding strength exceeded the minimum value of $0.4N/mm^2$ specified by the KS standard. All of the bio-composites with attached veneer satisfied the KS standard.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.39-44
• /
• 2016

This study was to investigate the characteristics of combustion toxic gases of pinus rigida specimens treated with chemical additives such as pyrophosphoric acid (PP)/ammonuium ion ($NH_4{^+}$), methylenepiperazinomethyl-bis-phosphonic acid (PIPEABP) and $PIPEABP/NH_4{^+}$. Each pinus rigida plates was painted in three times with 15 wt% of each chemical additives in the aqueous solution. After drying these specimens at room temperature, the production of combustion gases and smoke was examined by the cone calorimeter (ISO 5660-1). As a result, the peak mass loss rate time (PMLR time) treated with chemicals was delayed upto 10.5~47.4% compared to that of using untreated specimen. In addition, the peak production of carbon monoxide ($CO\;_{peak}$) of 32.1~71.4% and total smoke release rate (TSRR) of 15.6~43.6% for test pieces treated with the chemical additive were higher than that of using the virgin plate. In particular, for the specimens treated with the chemical additive, the rate of smoke release (RSR) 29.4~41.5% was obtained higher than that of untreated plate except the specimen treated with $PP/4NH_4{^+}$. It can thus be concluded that the treatment using the chemical additive could partially increase the combustion-retardation properties of the species when compared to those of the virgin plate.

• Korean Journal of Environment and Ecology
• /
• v.21 no.2
• /
• pp.168-175
• /
• 2007

For maximum utility of trails, there is a need for better knowledge of characteristics of trail use and its users. The purpose of this study is to find out users' attitudes toward trail structures in Eorimok exploring route in Hallasan National Park managerial purposes. A questionnaire survey was conducted to 138 people on the way back home from their visit to the site from July to August, 2007. The geological conditions of 7 types of pedestrian trail structures were rated relatively high both in quantity and quality. The responses were noticeably positive about the natural materials used in wood deck and PP rope railings from the point of three aspects: harmony with nature, visitor convenience and resources conservation. It seems necessary to replace steel structures with native materials because such unnatural materials used in a natural setting are subject to visitor's resistance.

• Journal of Conservation Science
• /
• v.16 s.16
• /
• pp.110-118
• /
• 2004

In order to evaluate two-step treatment of PEG-freeze drying for highly-degraded waterlogged ash woods (Fraxinus PP.; ca. 5,700 BP), which were excavated from peat lands in western Korea, dimension stability was examined during 45 months after complete treatment. The samples pre-treated with PEG in water solution showed better dimensional stabilities than the ones with PEG in t-butanol(TBA) solution. It suggests that TBA reduced the flexibility of wood cells and overflying by TBA induced micro-checks during freeze drying. Micro-checks results in fragile wood structures and consequently, large shrinkage by moisture absorbances of high PEG contents during exposure in humid condition. The results suggest that PEG in water-solution treatment is better than PEG in t-butanol as pretreament for freeze drying of highly-degraded waterlogged ash woods.

• Journal of Fisheries and Marine Sciences Education
• /
• v.14 no.1
• /
• pp.43-56
• /
• 2002

(1) This study was carried out to obtain seasonal fluctuations of marine debris in 5 beaches near the Southern Coast of Korea during May, 1999 - April, 2000. The results are as follows: 1. The density of marine debris was remarkably highest at Namhae beach among 5 beaches. The major part of debris in the beach was styrofoam, with the density of 348.5${ea/km}^2$. But, it was Songjung where the largest amount of resin pellets existed. 2. The composition of styrofoam consisted of 51% of the marine debris, wood& papers was 11%, resin pellets & plastics were 8% and others were 16%. 3. Seasonal fluctuations irregularly change in each beach, but the amount of resin pellets were found to be large only in September. It is estimated that resin pellets are beached upon the coastal beaches by the strong warm currents(Tushima currents) during the summer season. 4. Debris fabrication materials that were found had most of parts made up of PE 71.2%, PP 21.2% and EVA 7.7% through these surveys. 5. In the polluted state, the medium one among the 3 specifications(o1d, medium and new state) occupied 88.5% or so.

• Advances in materials Research
• /
• v.12 no.2
• /
• pp.119-131
• /
• 2023

The development of sustainable composites materials, from recycled polymeric materials and waste from the wood industry and stone processing, allows reducing the volume of these by-products, minimizing impacts on health and the environment. Nowadays, Polypropylene (PP) is the most recycled polymer in industry, while the furniture industry has increasingly used timber felled from sustainable forest plantations as a eucalypt. The powder tailing from the ornamental stone extraction and processing industry is commonly disposed of in the environment without previous treatment. Thus, the technological option for the development of composite materials presents itself as a sustainable alternative for processing and manufacturing industries, enabling the development of new materials with special technical features. The results showed that powder granite particles may be incorporated into the polypropylene matrix associated with short eucalyptus fibres forming green hybrid composites with potential application in structural engineering, such as transport and civil construction industries.

• Journal of Fisheries and Marine Sciences Education
• /
• v.12 no.2
• /
• pp.152-163
• /
• 2000

Floating resin pellets including plastics were surveyed from 7 coastal beaches near Young-il Bay during summer and winter season on 1998 ~ 2000 year. Plastic fabrication materials in the survey were founded with 6 items using the following; resin pellets, plastic debris, styrofoams, cigar filters, wood pieces and charcoals. The results deduced in the areas are as follows: 1. The seasonal variability of the all debris is revealed that summer season were remarkably larger than those of winter. This is deduced it is attributed to meteorological effects, e.g, the seasonal wind strength, current vectors and resorts of crowded people for beach enjoy. And the distribution of plastic debris is Pohang Songdo $12.9ea/m^2$, Pohang Bookbu $8.8ea/m^2$, Togoo $4.9ea/m^2$, Chilpo $3.2ea/m^2$, Hwajin $1.4ea/m^2$, Wolpo and Guryongpo $0.8ea/m^2$ respectively. 2. Compared with each beaches, Songdo beach, northern part beach of Pohang city and Togoo beach have higher densities than those of the others. Especially, the highest densities of all debris were discovered in the Songdo beach of Pohang city. 3. The change of density over the whole year was similarly distributed in quantities and fabrication materials. 4. These surveys were founded that the most parts of plastic debris materials were made up with PE and PP.

• Journal of Korean Society of Forest Science
• /
• v.83 no.4
• /
• pp.512-520
• /
• 1994

To enhance the utilization of Larch(Larix leptolepis Gorden) wood, the sawdusts were tested as cultivating media for Lentinus edodes(Mori 290) by varying the composition of the media. The economic efficiency for producing mushrooms from larch sawdusts was evaluated. The results are as follows. 1. Larch sawdust was as much efficient as oak sawdust in the growth of the mycelia and production of good quality of oak mushrooms. 2. The mushrooms were able to be harvested starting six months after beginning the cultivation. No differences were found among the qualities of the mushrooms produced by various treatments. 3. The contents of lignin(28.6-28.7%) in the fresh sawdust of larchwood are higher than those in the residues of the used media(18.2%). But lignin content of 1% NaOH extracts(30.4-34.4%) in fresh sawdust of larch was lower than those in the residues(68.0%). 4. The production of mushroom was relatively high to be 29.7-31.5%(760-780g.)/2.5kg pack) of mushroom weight. The net profit estimated was 1,475Won per pack.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2000.11a
• /
• pp.207-208
• /
• 2000

Since trichloroethylene (TCE), dichloroethylene (DCE), and vinyl chloride (VC) arise from anaerobic degradation of tetrachloroethylene (PCE) and TCE, there is interest in creating aerobic remediation systems that avoid the highly toxic VC and cis-DCE which predonominate in anaerobic degradation. However, it seemed TCE could not be degraded aerobically without an inducing compound (which also competitively inhibits TCE degradation). It has been shown that TCE induces expression of both the toluene dioxygenase of p. putida F1 as well as toluene-p-monooxygenase of P.mendocina KRI. We investigated here the ability of PCE, TCE, and chlorinated phenols to induce toluene-o-xylene monooxygenase (ToMO) from P.stutzeri OX1. ToMO has a relaxed regio-specificity since it hydroxylates toluene in the ortho, meta, and para positions; it also has a broad substrate range as it oxidizes o-xylene, m-xylene, p-xylene, toluene, benzene, ethylbenzene, styrene, and naphthalene; chlorinated compounds including TCE, 1, 1-DCE, cis-DCE, trans-DCE, VC, and chloroform : as well as mixtures of chlorinated aliphatics (Pseudomonas 1999 Maui Meeting). ToMO is a multicomponent enzyme with greatest similarity to the aromatic monooxygenases of Burkholderia pickettii PKO1 and P.mendocina KR1. Using P.sturzeri OX1, it was found that PCE induces P.mendocina KR1 Using P.situtzeri OX1, it was found that PCE induces ToMO activity measured as naphthalene oxygenase activity 2.5-fold, TCE induces 2.3-fold, and toluene induces 3.0 fold. With the mutant P.stutzeri M1 which does not express ToMO, it was also found there was no naphthalene oxygenate activity induced by PCE and TCE; hence, PCE and TCE induce the tow path. Using P.putida PaW340(pPP4062, pFP3028) which has the tow promoter fused to the reporter catechol-2, 3-dioxygenase and the regulator gene touR, it was determined that the tow promoter was induced 5.7-, 7.1-, and 5.2-fold for 2-, 3-, 4-chlorophenol, respectively (cf. 8.9-fold induction with o-cresol) : however, TCE and PCE did not directly induce the tou path. Gas chromatography and chloride ion analysis also showed that TCE induced ToMO expression in P.stutzeri OX1 and was degraded and mineralized. This is the first report of significant PCE induction of any enzyme as well as the first report of chlorinated compound induction of the tou operon. The results indicate TCE and chlorinated phenols can be degraded by P.stutzeri OX1 without a separate inducer of the tou pathway and without competitive inhibition.