• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.20-25
• /
• 1997

In this study, piezoelectric actuator samples were fabricated using 0.375PMN-0.37OPT-0.255PZ system ceramics with Barium substitution and the strain properties of them were investigated. Dielectric constant of the specimens increased with the increase of Ba content up to 5mol% and decreased with futher addition of Ba. The largest piezoelectric coefficient and electromechanical coupling coefficient were observed at the sintering temperature of 1250'C and Barium content of 5mol%. The characteristics of strain hysteresis was found largely with varing the sintering temperature on the single round type, and the strain is proportional to piezoelectric coefficient.

• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.21-26
• /
• 1988

The piezoelectric properties and temperatureproperties of resonant frequency of the pseudoquaternary soild solution 0.075 Pb(Sb$\frac{1}{2}$Nb$\frac{1}{2}$)O3-0.025 Pb(Mn1/3Nb2/3)O3-xPbTiO3-(0.9-x) PbZrO3 were investigated. The composition range examined are 0.32 x 0.57. Specimens were prepared by the conventional mixed oxide technique, calcined at 850$^{\circ}C$ for 1 hour and sintered at 1270$^{\circ}C$ for 2 hours under PbO atmosphere. From the results of XRD, dielectric and piezoelectric properties, it is supposed that the MPB composition between tetragonal and rhombohedral ferroelectric perovskite exists in 0.42$^{\circ}C$ was considered at the nearby MPB.

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.392-399
• /
• 1997

In this study, the effect of the sintering temperature on the dielectric and piezoelectric properties of 0.5 wt% $MnO_{2}$-doped $0.125Pb(Mg_{1/2}Nb_{2/3})O_{3}-0.435PbTiO_{3}-0.44PbZrO_{3}$ ceramics were investigated aiming at ultrasonic motor applications. From experimental result, it was found that the optimal sintering temperature condition was at $1270^{\circ}C$. The sample sintered at $1270^{\circ}C$ had density of $7.72\;g/cm^{3}$, dielectric constant of 570, dielectric loss of 0.82%, remanent polarization of $19.18{\mu}C/cm^{2}$, coercive field of 9.63 kV/cm, electromechanical coupling factor of radial mode of 55.1%, mechanical quality factor of 886. Temperature and frequency dependence of dielectric constant and dielectric loss of the sintered sample at $1270^{\circ}C$ was also investigated.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.156-156
• /
• 2000

The piezoelectric properties and the doping effect for $0.95Pb(Zr_xTi_{l-x})O_3+0.O5Pb(Mn_{1/3}Nb_{2/3})O_3$compositions were studied. Also, the heat generation and the change of electromechanical characteristics, the important problem in practical usage, were investigated under high electric field driving. As a experiment results under low electric field, the value of $k_p$ and ${\varepsilon}_{33}^T$ were maximized, but $Q_m$ was minimized $(k_p=0.57, Q_m=1550)$ in the composition of x=0.51. In order to increase the values of $Q_m$, $Nb_2O_5$ was used as a dopant. As the result of that, the grain size was suppressed and the uniformity of grain was improved. Also, the values of $k_p$ decreased, and the values of $Q_m$ increased with doping concentration of $Nb_2O_5$ . As a experiment results under high electric field driving, when vibration velocity was ower than 0.6[m/s], the temperature increase was 20[℃], and the change ratio of mechanical quality factor was less than 10[%]. So, its electromechanical characteristics was very stable. Conclusively, piezoelectric ceramic composition investigated at this paper is suitable for application to high power piezoelectric devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.661-664
• /
• 1999

The piezoelectric properties and the doping effect of Nb$_2$O$_{5}$ for 0.95 PbZr$_{x}$ Ti$_{1-x}$ -O$_3$+0.05 Pb(Mnsub 1/3/Nb$_{2}$3/)O$_3$ compositions have been investigated. In the composition of 0.95PbZr$_{0.51}$Ti$_{0.49}$O$_3$+0.05Pb(Mn$_{1}$3/Nb/syb 2/3/)O$_3$ the values of k$_{p}$ and $\varepsilon$$_{33}$ $^{T}$ are maximized, but Q$_{m}$ was minimized (k$_{p}$ =0.57, Q$_{m}$ =1550). The grain size was suppressed and the uniformity of grain was improves with doping concentration of Nb$_2$O$_{5}$ far 0.95PbZr$_{0.51}$Ti$_{0.49}$O$_3$+0.05Pb(Mn$_{1}$3/Nb/syb 2/3/)O$_3$. sample. The values of k$_{p}$ first decreased slightly when a small amount of Nb$^{5+}$ is doped and then decreased when the Nb$^{5+}$ concentration is further increased. The Q$_{m}$ . OR the Other hand. increased monotonously with doping concentration of Nb$_2$O$_{5}$ .{5}$ . .

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.669-672
• /
• 1999

In this paper, we studied the properties of small-size disk-type ultrasonic motor using travelling wave for the application to the precise control robotic joint motor and fabricated it. The diameter of the ultrasonic motor fabricated was 13mm. Also, the piezoelectric vibrator was constructed by piezoelectric ceramic and elastic material. The piezoelectric ceramic was composed to PZ-PT-PMN which was shown the high electromechanical stability under high vibration level and stainless steel was used as the elastic material in which configuration was disk-type. To conform the capability of application to robotic motor, we measured the change of rotational speed according to applied voltage and applied frequency. As the results, the small-size disk-type ultrasonic motor was able to fabricate, and the revolution speed was 350 (rpm) when input voltage was 55 (Vrms) and applied frequency 160.4 IkHz] under pre-load.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.594-597
• /
• 2003

In the present study, the piezoelectricity and polarization of multilayer ceramic actuator, being designed to stack PMN-PZ-PT ceramic layers and Ag-Pd electrode layers alternatively, were investigated under a consideration of geometric factor, the volume ratio of the ceramic to the electrode layers. The actuators were fabricated by tape casting of 0.2Pb(Mg1/3Nb2/3)O3-0.38PbZrO3-0.42PbTiO3 followed by lamination and burnout & co-firing processes. The actuators of 10 10 0.62 nm3 in size were formed in a way that 60 200 m thick ceramics were stacked alternatively with 5 m thick electrode layer. Increases in polarization and electric field-induced displacement with thickness of the ceramic layer were attributed to change of 90o/180o domain ratio, which was affected by interlayer internal stress. The piezoelectricity and actuation behaviors were found to depend upon the volume ratio (or thickness ratio) of ceramic to electrode layers.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1720-1722
• /
• 1999

In this paper, we studied the properties of small-size disk-type ultrasonic motor using travelling wave for the application to the precise control robotic joint motor and fabricated it. The diameter of the ultrasonic motor fabricated was 13mm. Also, the piezoelectric vibrator was constructed by piezoelectric ceramic and elastic material. The piezoelectric ceramic was composed to PZ-PT-PMN which was shown the high electromechanical stability under high vibration level and stainless steel was used as the elastic material in which configuration was disk-type. To conform the capability of application to robotic motor, we measured the change of rotational speed according to applied voltage and applied frequency. As the results, the small-size disk-type ultrasonic motor was able to fabricate, and the revolution speed was 350 [rpm] when input voltage was 55 [Vrms] and applied frequency 160.4 [kHz] under pre-load.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.282-284
• /
• 1997

Ultrasonic motors using piezoelectric ceramics and brass metal endcaps were fabricated, which is operated by single - phase high frequency. The structure of the ultrasonic motors has the wind-mill type. The stator part consists of a piezoelectric disk and two metal endcaps slotted wind-mill type. According to the piezoceramic disk vibrates as a radial mode, two metal endcaps provide both longitudinal and torsional displacements simultaneously. Because the metal endcaps have a nonsymmetric structure. the principle of the ultrasonic motor is not well understood. The dimension of the ultrasonic motor is diameter in 12.7 mm and thickness in 2.0 mm, and especially the PMN-PT-PZ piezoelectric disk was used. The maximum revolution speed 700 rpm and the maximum torque 0.22 mN.m were obtained. The ultrasonic motor for rotation was Supplied only single phase AC.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.163-168
• /
• 2003

In the present study, the piezoelectricity and polarization of multilayer ceramic actuator, being designed to stack PMN-PZ-PT ceramic layers and Ag-Pd electrode layers alternatively, were investigated under a consideration of geometric factor, the volume ratio of the ceramic to the electrode layers. The actuators were fabricated by tape casting of $0.2Pb(Mg_{1/3}Nb_{2/3)O_3-0.38PbZrO_3-0,42PbTiO_3$ followed by lamination and burnout & co-firing processes. The actuators of $10\times10\times0.6~2\textrm{mm}^3$ in size were formed in a way that $60 ~ 200\mu\textrm{m}$ thick were stacked alternatively with $5\mu\textrm{m}$ thick electrode layer. Increases in polarization and electric field-induced displacement with thickness of the ceramic layer were attributed to change of $90^{\circ}$/$180^{\circ}$ domain ratio, which was affected by interlayer internal stress. The piezoelectricity and actuation behaviors were found to depend upon the volume ratio (or thickness ratio) of ceramic to electrode layers.