• Journal of Radiation Protection and Research
• /
• v.1 no.1
• /
• pp.15-21
• /
• 1976

The present investigation was intended to study the state of Pm-147 in solution and its adsorbed state on membrane filters by varying the concentrations of Pm-147 solution and its pH. Also, the study on the coprecipitation of Pm-147 with $Fe(OH)_3$ was carried out by varying, amounts of $Fe(OH)_3$ and pH of the solution. The carrier-free Pm-147 exists in an ionic state of $Pm^{3+}$ in solution, and is adsorbed on membrane filter in filtration process. The adsorbed state of Pm-147 on the membrane filter shows various ionic state at a constant ionic strength of 0.1M NaCl, that is, $Pm^{3+}$ state exists until pH value of 5.0, then gradually $Pm(OH)^{2+}$ state appears between pH value of 5.0 to 6.0, and the state of $Pm(OH)_2^+$ and $Pm(OH)_3$ would be expected at the higher pH value of 6.0. Coprecipitation of Pm-147 on $Fe(OH)_3$ is an adsorption penomenon in an ionic state of $Pm^{3+}$ in acidic condition. At higher pH and larger amount of Fe carrier, the adsorbed state of Pm-147 shows $Pm(OH)^{2+}$ and $Pm(OH)_2^+$ state. As a results of the present studies, it is seen that the characteristic of carrier free radioisotopes is not due to the radioactivity, but due to the adsorption of ultramicroquantity of radioisopes. Therefore, the knowledge on the ultramicroquantity of radioisotopes could help for the solution of decontamination in handing and chemical procedure with radioisotopes.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.527-534
• /
• 2006

Modern passenger cars with diesel engines are equipped with DOC(diesel oxidation catalyst) for the purpose of reducing HC and CO in the exhaust stream. Cold start exhaust emissions pose troubles here as on gasoline engine vehicles. As a result, some of the diesel passenger cars roll off todays the assembly lines with WCC(warm-up catalytic converter). Oxidation characteristics of the particulates in WCC is analyzed in this study by EEPS(engine exhaust particulate size spectrometer). The maximum number of PM is found to come out of WCC in sizes near 10nm when an HSDI diesel engine is operated under the conditions of high speed and medium to heavy load. When the temperature of the WCC exceeds $300^{\circ}C$, the number of PM smaller than 30 nm in diameter sharply increases upon passing through the WCC. Total mass of emitted PM gets reduced downstream of the WCC under low speed and light load conditions due to adsorption of PM onto the catalyst. Under conditions of high speed and medium to heavy load, the relatively large PM shrink or break into fine particles during oxidation process within the WCC, which results in more mass fraction of fine particles downstream of the WCC.

• Smart Structures and Systems
• /
• v.22 no.2
• /
• pp.151-159
• /
• 2018

Maintenance activities are regarded as a key part of the repairable deteriorating system because they maintain the equipment in good condition. In practice, many maintenance policies are used in engineering fields to reduce unexpected failures and slow down the deterioration of the system. However, in traditional maintenance policies, maintenance activities have often been assumed to be performed at the same time interval, which may result in higher operational costs and more system failures. Thus, this study presents two non-periodic preventive maintenance (PM) policies for repairable deteriorating systems, employing the failure rate of the system as a conditional variable. In the proposed PM models, the failure rate of the system was restored via the failure rate reduction factors after imperfect PM activities. Operational costs were also considered, which increased along with the operating time of the system and the frequency of PM activities to reflect the deterioration process of the system. A numerical example was provided to illustrate the proposed PM policy. The results showed that PM activities performed at a low failure rate threshold slowed down the degradation of the system and thus extended the system lifetime. Moreover, when the operational cost was considered in the proposed maintenance scheme, the system replacement was more cost-effective than frequent PM activities in the severely degraded system.

• The Korean Journal of Health Service Management
• /
• v.11 no.4
• /
• pp.53-65
• /
• 2017

Objectives : The purpose of this study was to explore and describe the factors related to clinical nurses' organizational socialization, process and to find out the strategic information for successful organizational socialization. Methods : Data were collected with a structured questionnaires from 300 clinical nurses. The data were analyzed with SPSS/WIN 21.0. Results : First, the average score for the organizational socialization($2.95{\pm}0.37$), organization climate($3.28{\pm}0.43$), autonomy($3.23{\pm}0.43$), role stress($3.21{\pm}0.56$), professional self-concept($3.19{\pm}0.46$), organization value internalization($3.11{\pm}0.59$), and perceptional justice($2.91{\pm}0.50$). Second, influencing factor of organizational socialization of the participant were organizational climate, role stress, professional self-concept, Job esteem, Living arrangement type, collaboration between medical professionals in hospital, the other hospital work experience, role model or Mentor, total hospital career, perceived health status, spouse, perceptional justice, Adjusted $R^2=.702$. Conclusions : These results suggest that organizational socialization of clinical nurses could be enhanced by organizational climate. Thus creating a positive organizational climate are mandated for clinical nurses to have constructive organizational socialization.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.2
• /
• pp.114-118
• /
• 2001

In manufacturing process of Changran-Jeotgal, agitation with 10 rpm for 10 min/4 hrs of Changran-Jeotgal without released extract was carried out during the fermented process at $0\pm2^{\circ}C$ to shorten the fermentation period and uniform product quality, This step was called Improved process, while the step with release extract and standing fermentation was Conventional process. During 60 days of fermentation period, chemical, microbiological changes and sensory evaluation were examined, Brix, VBN and $NH_2-N$ were 27.4, $54.3\;mg\%\;and\;87.9 mg\%$ on 30th day in Improved process, respectively, but they were 27.1, $57.8\;mg\%\;and\;96.6\;mg\%$ on 50th day in Conventional process. The pH value was decreased from 7.0 to $\6.3\~6.5$ in both of them, The viable cell counts in Improved process was increased from $6.6\times10^3CFU/g\;to\;2.6\times10^6CFU/g$ during 30 days, in Conventional process, slowly increased from $5.8\times10^3CFU/g\;to\;1.9\times10^6CFU/g$ during 50 days. Sensory evaluation showed that products on 30th day in Improved process and products on 50th day in Conventional process were best favorable. From above results, we found that the fermentation with agitation shortened the fermentation period by 20 days compare to standing fermentation.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.5
• /
• pp.601-614
• /
• 2013

The commercial charcoal kiln was projected the largest source of biomass burning sector in Korea. Commercial charcoal kiln was operated to emit air pollutants into the air without any air pollution prevention equipment. The object of this field survey was to understand characteristics of air pollutants concentration and emission factors and to provide preliminary data for effective processor from oak charcoal manufacturing process. As result of field survey, TSP, $PM_{10}$ and $PM_{2.5}$ concentration from charcoal kiln were 400~37,000 $mg/m^3$. These values were over the 100 $mg/m^3$ in TSP, this value was effluent quality standard of Clean Air Conservation Act. The average concentration of CO, $SO_2$ and TVOC were 2~5%. 0~110 ppm and 820~10,000 ppm respectively. The emission factors were 42.4 g-PM/kg-oak in TSP, 40.3 g-PM/kg-oak in $PM_{10}$, 38.2 g-PM/kg-oak in $PM_{2.5}$, 182.5 g-CO/kg-oak, 1.0 g-NO/kg-oak, $SO_2$ 0.2 g-$SO_2/kg$-oak and 104.4 g-TVOC/kg-oak. The part of commercial charcoal kiln had air pollution prevention equipment but it was difficult to work properly. Much wood tar excreted in exhaust emissions from oak charcoal manufacturing process. This wood tar was cause of many troubles sticking in the air pollutant prevention equipment. For handling particulate matters and gaseous air pollutants from oak charcoal manufacturing process in biomass burning, air pollutant prevention equipment design and management needs preprocessor for removal wood tar.

• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.8-15
• /
• 2002

Tetrahedral amorphous carbon(ta-C) films were deposited by the filtered vacuum arc(FVA) process. The FVA process has many advantages such as high ionization ratio and the ion energy, which is suitable for dense amorphous carbon film deposition. However, the energy of the carbon ion cannot be readily controlled by manipulating the arc source parameters. In order to control the film properties in wide range, we investigated the dependence of the film properties on the substrate bias voltage. The mechanical properties and the density of the film exhibit the maximum values at about -100 V of the bias voltage. The maximum values of hardness and density were respectively 54$\pm$3 GPa and 3.6$\pm$0.4 g/㎤, which are 3 to 5 times higher than those of the films deposited by RF PACVD or ion beam process. The details of the atomic bond structure were analysed by Raman and NEXAFS spectroscopy. The change in the film properties for various bias voltages could be understood in the view of the $sp^2$ and $sp^3$ bond fraction in the deposited films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.229-236
• /
• 1998

Ferroelectric $Sr_xBi_yTa_2O_{9+\alpha}$/(0.7$\leqSr\leq1.0,\; 2.0\leqBi\leq2.6)$ solutions were prepared by MOD (Metalorganic Deposition) process. These solutions were made into thin films with thickness ranging from 1500~2000${\AA}$ by spin coating. The phase transformation of the SBT thin films by variation of annealing temperature and annealing time were observed using high temperature XRD and SEM. The crystallization and grain growth of SBT thin film were accomplished at $800^{\circ}C$ for 30 minutes after deposition of Pt top electrode by sputtering to prevent electrical breakdown. Ferroelectric properties of the SBT thin films were measured in the range of $\pm$3V\; and\; \pm5V$. The specimen with composition ratio of Sr/Bi/Ta (0.8/2.4/2.0) has the excellent ferroelectric properties ; $2P_r = 10.5,\; 13.2\muC/cm^2 \;at\; \pm3V\; and\; \pm5V$ respectively. Observing the post annealed Pt/SBT/Pt interface by SEM, it was found that Pt electrode sputtered on to the SBT thin film penetrated into the hollow on the SBT thin film, thus decreasing the effective insulation thickness. The effective insulation thickness recovered by post annealing, and this was confirmed by leakage current density measurement.

• Physical Therapy Korea
• /
• v.17 no.2
• /
• pp.25-32
• /
• 2010

The purpose of this study was to investigate the most effective and comprehensible method for the assessment of resting scapular position (RSP) and pain level (PL) in unilateral shoulder pain (USP). Fifty volunteers with USP were involved in the study. Resting scapular assessments of the patients' pain sides (PS) and non-pain sides (NPS) were evaluated. The assessment tools for RSP are: 1) sternal notch (SN) to coracoid process (CP) distance 2) 3rd thoracic spinous process (T3S) to posterolateral angle of acromion (PLA) distance 3) scapular index 4) 8th thoracic spinous process (T8S) to inferior angle of scapular (IAS) distance 5) supine measurement of pectoralis minor (PM) distance 6) standing PM distance 7) PM index (PMI) and 8) PM pain. The paired t-test was used to compare PS and NPS in RSP. Pearson correlation analysis was used to confer a relationship between the PL and RSP. The results of this study indicated that: 1) all the variables between the PS and NPS for RSP were statistically significant(p<.05) and 2) the PMI showed the strongest relationship in the correlation analysis between RSP and PL(p<.05, r=.37). Therefore, it can be concluded that there is a relationship between PMI and PL and it is suggested that an assessment tool using PMI to diagnose shoulder pain would be clinically effective.

• Journal of Ginseng Research
• /
• v.28 no.1
• /
• pp.18-26
• /
• 2004

The effect of Panax ginseng administration in muscle inflammatory process induced after eccentric exercise, that causes myofibrillar disruption, was studied. Changes in lipid peroxidation, inflammation, glycogen levels in muscle and release of myocellular proteins to blood were measured. The analyses were performed immediately after eccentric exercise and over week since this period are necessary for the muscle damage-repair cycle. The ginseng extract (100 mg kg$^{-1}$ ) was orally administered to rats for three months, before the eccentric exercise performance. The results showed the protective role of ginseng against skeletal muscle damage. This effect could be associated with their membrane stabilising capacity since creatine kinase (CK) activity was significantly decreased 96 h post-exercise from 523$\pm$70 to 381$\pm$53 and 120 h post-exercise from 443$\pm$85 to 327$\pm$75 in treated animals. $\beta$-glucuronidase activity, as indicator of inflammation, showed a significant reduction of about 15-25% in soleus, vastus and triceps in these post-exercise times. The lipid peroxidation, measured by malondyaldehyde levels, was significantly decreased in the 24 h post-exercise period in soleus and vastus intermedius muscles and on the recovery period. Finally ginseng administration reduced significantly the decrease of the glycogen levels immediately after exercise and when the regenerative process took place (72-168 h post exercise). Collectively, the results have showed that ginseng did not inhibit the vital inflammatory response process associated with the muscle damage-repair cycle but presumably ameliorate the injury.