• Explosives and Blasting
• /
• v.33 no.2
• /
• pp.15-24
• /
• 2015

In general, blast vibrations could make underground cavern unstable by causing relative movements between the surrounding rock blocks that are divided by discontinuities such as joints and faults around the cavern. In the study, a blast guideline was established to obtain the stability of a large-scale cavern for underground crusher room in an open pit limestone mine in Korea. The guideline was suggested in the form of a standard calculation method of the maximum charge per delay for a safe blast. The allowable level of peak particle velocity for the cavern was determined based on the result of a numerical analysis using FLAC2D. The ground vibration data required for the study was obtained from field measurements.

• Journal of Surface Science and Engineering
• /
• v.39 no.1
• /
• pp.25-34
• /
• 2006

Al-Mg alloy, an open rack vaporizer(ORV) material was reported to be corroded in seawater environments though the ORV material was coupled to thermally sprayed Al-Zn alloy functioning a sacrificial anode. In addition, the corrosion behavior based on the calculated corrosion potential did not match the observed corrosion behavior. Hence, the goal of this study is to get better understanding on Al or Al-Mg alloy coupled to Al-Zn alloy and to provide the calculated corrosion potential representing the corrosion behavior of the ORV material by immersion test, electrochemical tests, and calculation of corrosion and galvanic potential. The corrosion potentials of Al and Al alloys also depended on alloying element as well as surface defects. The corrosion potentials of Al and Al-Mg alloy were changed with time. In the meantime, the corrosion potentials of Al-Zn alloys were not. The corrosion rates of Al-Zn alloys were exponentially increased with zinc contents. The phenomena were explained with the stability of passive film proved by passive current density depending on pH and confirmed by the model proposed by McCafferty. Dissimilar material crevice corrosion (DMCC) test shows that higher content of zinc caused Al-Mg alloy corroded more rapidly, which was due to the fact that higher corrosion rate of Al-Zn makes [$H^+$] and [$Cl^-$] more concentrated within pit solution to corrode Al-Mg alloy. Considering electrochemical reactions within pit as well as bulk in the calculation gives better prediction on the corrosion behavior of Al and Al-Mg alloy as well as the capability of Al-Zn alloy for corrosion protection.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.12
• /
• pp.211-217
• /
• 2020

This study is to find out the effectiveness by adult CPR method of a single rescuer. For patients with acute cardiac arrest, CPR is the only first aid, and chest compression is the most important of these techniques. The subjects of this study were freshman, 120 subjects who did not learn CPR, and for data analysis, the SPSS 22.0 Version was used. The accuracy of chest compression site selection was significantly higher in the upper part of the two fingers in the pit of the stomach(p<.001), and the ease was also high(p<.001). In the case of the general public, they select the chest compression area easily and quickly, it turns out that it is easier to designate the landmark toward the pit of the stomach. In the future, through various job groups, research to select the chest compression site is needed, and additional studies should be conducted to confirm the maintenance and accuracy during chest compression.

• PNF and Movement
• /
• v.21 no.2
• /
• pp.231-241
• /
• 2023

Purpose: Weakness of the vastus medialis oblique muscle (VMO), or the imbalance between VMO and vastus lateralis muscle (VL) activity, is one of the most important factors in knee joint problems. Rigid taping techniques, such as patellar inhibition taping and VL inhibition taping, are frequently used in clinical practice to treat knee joint problems. The purpose of this study was to compare the acute effect of three different types of taping (patellar inhibition taping (PIT), distal VL inhibition taping (DVLIT), and proximal VL inhibition taping (PVLIT)) on electromyography (EMG) activity of VMO, VL, and VMO:VL ratio during walking. Methods: Thirty-eight normal healthy subjects (38 males; mean age = 31.00 years) voluntarily participated in this study. EMG was applied to investigate muscle activation during walking. Repeated measures of ANOVA and one-way ANOVA compared the three different conditions (PIT, DVLIT, and PVLIT) for each variable. Results: VMO and VL activation were significantly increased after PTIT application, and VMO and VL activation were significantly decreased after DVLIT and PVLIT application. The VMO:VL ratio increased after the three types of taping application, but there were no significant differences among the three types of taping. Conclusion: Based on the results of this study, PTIT is more effective than DVLIT and PVLIT in increasing the muscle activation of the VMO and VL during walking. Also, DVLIT is more effective for increasing the VMO:VL ratio and has beneficial effects on the imbalance between VMO and VL activity.

• Geomechanics and Engineering
• /
• v.30 no.6
• /
• pp.489-502
• /
• 2022

In this study, a Gaussian process regression (GPR) model as well as six GPR-based metaheuristic optimization models, including GPR-PSO, GPR-GWO, GPR-MVO, GPR-MFO, GPR-SCA, and GPR-SSO, were developed to predict fly-rock distance in the blasting operation of open pit mines. These models included GPR-SCA, GPR-SSO, GPR-MVO, and GPR. In the models that were obtained from the Soungun copper mine in Iran, a total of 300 datasets were used. These datasets included six input parameters and one output parameter (fly-rock). In order to conduct the assessment of the prediction outcomes, many statistical evaluation indices were used. In the end, it was determined that the performance prediction of the ML models to predict the fly-rock from high to low is GPR-PSO, GPR-GWO, GPR-MVO, GPR-MFO, GPR-SCA, GPR-SSO, and GPR with ranking scores of 66, 60, 54, 46, 43, 38, and 30 (for 5-fold method), respectively. These scores correspond in conclusion, the GPR-PSO model generated the most accurate findings, hence it was suggested that this model be used to forecast the fly-rock. In addition, the mutual information test, also known as MIT, was used in order to investigate the influence that each input parameter had on the fly-rock. In the end, it was determined that the stemming (T) parameter was the most effective of all the parameters on the fly-rock.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.130-133
• /
• 2001

A multifilamentary Bi-2223 HTS tape for superconducting power applications was studied through the fabrication of 250-meter long tapes by the PIT(powder in tube) process. To fabricate continuous long wire, a drawing machine, a two-drum bull block and a rolled tape winding machine were developed. Especially, 250-meter long tapes were heat treated in the shape of pancake coil to reduce the heat affect zone and to achieve the high critical current. Engineering critical current density was improved through both the enhancements of critical current density by control of thermal process and the increase of filling factor by using thin Ag alloy sheath tubes less than 1.5 mm in thickness. We have made successfully 250-meter long 37 filamentary tapes with high filling factor up to 31 % employing the modified drawing and rolling technique. The critical current of 250-meter long tapes with pancake coil type was measured by transport method at self-field up to 250 gauss of center field. The measured values, based on the transport critical current at self-field, $I_{c}$ -B characteristics and magnetic field analysis, are 34 A of I$_{c}$ and 4.0 $kA/\textrm{cm}^2$ of $J_{e}$ at 250 m, 77 K, and 0 T. We also have achieved the 56 A of I$_{c}$ and 7.0 $0 kA/\textrm{cm}^2$ of$ J_{e}$ in short tapes at 77K, self-field, and 1$mutextrm{V}$/cm.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.214-220
• /
• 2003

Pipe jacking is a name for a method to excavate a tunnel by pushing pipe into the ground from an especial pit. Size of tunnels in this method is different from under 900mm (microtunneling) to more than 3,000mm. Method of excavation is also different from hand digging to use of any kind of tunnel boring machines such as slurry and earth pressure balance (EPB) machines. Slurry pipe jacking was firmly established as a special method for the nondisruptive construction of the underground tunnels in urban area. During the pipe jacking and microtunneling process, the jacking load is an important parameter, controlling the pipe wall thickness, need to and location of intermediate jacking station, selection of jacking frame and lubrication requirements. The main component of the jacking load is due to frictional resistance. In this paper the skin friction between pipe surface and surrounding condition also lubricant quality based on a few fundamental tests, were considered. During this study unconfined compressive strength test, dynamic friction measurement test and direct shear box test were raised for one of the largest diameter slurry pipe jacking project in Fujisawa city in Japan. It could be concluded that in slurry pipe jacking, prediction of frictional forces are mainly dependent on successful lubrication, its quality and lubricant strength parameters. Conclusions from this study can be used for the same experiences.

• Korean Journal of Materials Research
• /
• v.3 no.4
• /
• pp.403-409
• /
• 1993

In this paper, an $NH_3$, added during dry oxidation and annealing m Si( 111) is clarified effect ive to suppress or remove defects. Annealing effects in $N_2$ and $NH_3/N_2$ ambient are estimated with dry $O_2$ and $NH_4$ oxidation($NH_3$ added in dry $O_2$ oxidation) method. C;em'rated defects in dry $O_2$ oxidation are lengthened according to oxidation time. but any defects in $NH_3$ oxidation are not found. Dry oxidation, after $NH_3$ oxidation as an initial oxidation. lias the defect -removing effect at the interface of Si -$SiO_2$. After dry or $NH_3$. oxidation. the annealmg 7.5% $NH_3/N_2$ ambient brings out gettering effect of OSF. The annealing in 7.5% $NH_3/N_2$ ambient for NI L oxidation method decreaSE,s $NH_3$ length of OSF about 20 % compared with dry oxidation method. Tlw feature of OSF is pit type, the gettering is directed to (011) plane for (111) plane. and OSFs are etched following to 110) directIon.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.6
• /
• pp.536-543
• /
• 2023

Speaker diarization, which labels for "who spoken when?" in speech with multiple speakers, has been studied on a deep neural network-based end-to-end method for labeling on speech overlap and optimization of speaker diarization models. Most deep neural network-based end-to-end speaker diarization systems perform multi-label classification problem that predicts the labels of all speakers spoken in each frame of speech. However, the performance of the multi-label-based model varies greatly depending on what the threshold is set to. In this paper, it is studied a speaker diarization system using single-label classification so that speaker diarization can be performed without thresholds. The proposed model estimate labels from the output of the model by converting speaker labels into a single label. To consider speaker label permutations in the training, the proposed model is used a combination of Permutation Invariant Training (PIT) loss and cross-entropy loss. In addition, how to add the residual connection structures to model is studied for effective learning of speaker diarization models with deep structures. The experiment used the Librispech database to generate and use simulated noise data for two speakers. When compared with the proposed method and baseline model using the Diarization Error Rate (DER) performance the proposed method can be labeling without threshold, and it has improved performance by about 20.7 %.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.481-484
• /
• 1999

The undoped-InSe and Sn-doped InSe single crystals were grown by vertical Bridgman method and their properties were invesigated. These crystals were obtained by lowering the quartz ampoule for growth in the furnace and growth rate at optimum condition is 0.4mm/hr. The orientations and the crystallinites of these crystals were identified by X-ray diffraction(XRD), double crystal rocking curve(DCRC) and etch-pit density(EPD) measurements. From the Raman spectrum at room temperature, TO, LO modes together with their overtones and combinations were observed. Optical properties were investigated by photoluminescence at 12K and direct band gap of these crystals obtained from optical absorption spectrum. Compared with undoped-lnSe, electrical properties of Sn-doped InSe were increased and the electrical conductivity type were n-type. But electrical properties along growth direction of crystals and radial direction of wafer showed nearly uniform distribution.