• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2114-2117
• /
• 2014

Joint pain is generally a common disorder not only for the old aged people but also for the immunocompromised patients. The present proposed study reveals the presence of inflammatory diseases in joint generally diagnosed by removing synovial fluid and changes in the volume and composition are examined for the presence of WBC and crystals. This study implement a non-invasive approach to identify the changes in joint fluid by measuring the changes in electrical property of the synovial tissue under the influence of electrical current signal with frequency range between 100 kHz to 300 kHz. The response of tissue for the current signal was measured in terms of potential drop across the tissue. The hardware system design consists of input and output sections. The input section which applies current signal to upper limb joint region is made of ICL8038 function generator IC with amplifier and voltage to current converter. The output section picks voltage variation using metal surface electrode, amplifier, ADC, PIC microcontroller and LCD interface. 100 patient inclusive of normal and disease affected patients where examined for upper limb synovial fluid variation and inflammatory diseases were identified.

• 전기전자학회논문지
• /
• 제23권3호
• /
• pp.1068-1076
• /
• 2019

오늘날 우리가 사용하고 있는 대부분의 전자제품에는 마이크로 컨트롤러가 내장되어 있으며, 이를 내장한 미니컴퓨터를 임베디드 시스템이라고 한다. 이러한 소규모 환경에서는 마이크로 컨트롤러에 응답성이 매우 중요한데 본 논문에서는 마이크로 컨트롤러에 기본적인 입출력 제어, 타이머/카운터 인터럽트 동작원리 및 이해에 대한 내용과 더불어 마이크로 컨트롤러 내의 플래시메모리에 각 프로그램 실행 루틴인 메인 루틴 및 인터럽트 서비스루틴에 대한 특징 및 프로그램 실행 순서를 컨트롤하여 처리율과 레이턴시를 개선하는 프로그램 로직을 제안하고 있다. 본 논문에서의 하드웨어 시뮬레이션은 아트멜사와 마이크로칩사에서 출시한 ATmega128과 PIC16F877A 마이크로 컨트롤러를 이용하여 검증이 실시되었다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권10호
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.468-471
• /
• 2005

The Air Quality Sensor(AQS), located near the fresh air inlet, serves to reduce the amount of pollution entering the vehicle cabin through the HVAC(heating, ventilating, and air conditioning) system by sending a signal to close the fresh air inlet door/ventilation flap when the vehicle enters a high pollution area. One chip sensor module which include above two sensing elements, humidity sensor and bad odor sensor was developed for AQS (air quality sensor) in automobile. With this sensor module, PIC microcontroller was designed with back propagation neural network to reduce detecting error when the motor vehicles pass through the dense fog area. The signal from neural network was modified to control the inlet of automobile and display the result or alarm the situation. One chip microcontroller, Atmega128L (ATmega Ltd., USA) was used. For the control and display. And our developed system can intelligently detect the bad odor when the motor vehicles pass through the polluted air zone such as cattle farm.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권4호
• /
• pp.231-237
• /
• 2006

This paper proposes an effective drive of high intensity discharge (HID) lamp ballast for cars. All control functions of the proposed ballast are implemented using a low-cost single chip microcontroller, PIC16C73 to optimize the total system size and to minimize cost through minimization of total component number. The proposed ballast generates high open-circuit voltage to ignite the lamp and is controlled to supply effectively the power required to shorten warm-up period after the breakdown. The DC-DC converter of the DC-AC converter part of the ballast utilizes the flyback converter topology that can minimize component number. Also, because to more minimize the ballast size, the transformer size must be minimized, for this, PWM (Pulse Width Modulation) pulses are generated with high frequency using the PWM module of the microcontroller. An analysis for this is explained, briefly. As if the operation of the lamp and ballast arrives at steady-state, then the ballast must AC-control the lamp, for this, the microcontroller utilizes the other PWM module. And the part related to the igniter is explained, briefly. It is shown through experimental results that the controller of the proposed ballast has good performance for the HID lamp for cars.

• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.413-430
• /
• 2019

This paper presents an optimum hybrid SVPWM technique for three-level voltage source inverters (VSIs). The proposed hybrid SVPWM technique aims to minimize total harmonic distortion (THD). A new parameter is introduced to incorporate the heterogeneous nature of switching sequences of SVPWM technique. The proposed hybrid SVPWM technique is implemented on a low-cost PIC microcontroller (PIC18F452) and verified experimentally with a 2 KVA three-phase three-level insulated gate bipolar transistor-based VSI. Optimum switching sequence results in the three-level inverter configuration are demonstrated. The proposed hybrid SVPWM technique improves the THD performance by 17.3% compared with the best available three-level SVPWM technique.

• 한국산학기술학회논문지
• /
• 제4권2호
• /
• pp.63-70
• /
• 2003

본 논문에서는 반도체 제조장비의 핵심 부품 중에 하나인 질량유량제어기(MFC, Mass Flow Controller)클 설계하고 구현하였다 Microchip社의 마이크로콘트롤러(Microcontroller) PIC 16F876을 사용하여 개발된 MFC는 여러가지 문제점을 가진 아날로그(Analog) 방식의 MFC와 고가의 DSP(Digital Signal Processor) 및 고분해능의 AD변환기(Analog to Digital Convertor)를 사용하는 디지털 MFC의 장점을 혼합한 하이브리드형(Hybrid-Type)이다. 본 논문에서 개발된 MFC는 크게 센서부(Sensor Unit), 제어부(Control Unit), 구동기부(Actuator Unit)로 구성되었으며, 성능향상을 위한 자동보정(Automatic Calibration) 알고리즘과 표준테이블(Reference Table) 방식을 사용하였다.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1244-1255
• /
• 2017

The space vector pulse width modulation (SVPWM) technique is a popular PWM method for medium voltage drive applications. Conventional SVPWM (CSVPWM) and bus clamped SVPWM (BCSVPWM) are the most common SVPWM techniques. This paper evaluates the performance of various advanced BCSVPWM strategies in terms of their harmonic distortion and switching loss based on a uniform frame work. A uniform frame work, pulse number captures the performance parameter variations of different SVPWM strategies for various number of samples with heterogeneous pulse numbers. This work compares different advanced BCSVPWM techniques based on the modulation index and location of the clamping position (zero vector changing angle ) of a phase in a line cycle. The frame work provides a fixed fundamental frequency of 50Hz. The different BCSVPWM switching strategies are implemented and compared experimentally on a 415V, 2.2kW, 50Hz, 3-phase induction motor drive which is fed from an IGBT based 2 KVA voltage source inverter (VSI) with a DC bus voltage of 400 V. A low cost PIC microcontroller (PIC18F452) is used as the controller platform.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.568-570
• /
• 2004

This paper presents a study of a position finding system using PSD Sensor and Pan/Tilt. The position of PSD(Position Sensitive Detector) sensor is calculated by the degree of pan-tilt and the difference in height between pan-tilt and PSD. For that, the DSP which control pan-tilt is used for precise operation. The PIC microcontroller process PSD sensor data that indicate light incident position. A user using computer can acquire the conditions of pan-tilt and PSD and issue an order.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 제14회 신호처리 합동 학술대회 논문집
• /
• pp.849-852
• /
• 2001

본 눈문에서는 뒤틀림, 응력, 압력[1], 토크, 가속도 등의 물리적인 동적 현상을 측정하여 수집된 데이터를 처리하기 위한 신호처리(Signal Processins) 기능이 결합되어 넓은 용도로 활용할 수 있는 센서 신호 수집 시스템을 구현하였다. 구현된 시스템은 data acquisition board 의 하드웨어와 소프트웨어로 나누어 볼 수 있다. 하드웨어의 구성은 아날로그부, 디지털부, 그리고 시스템 인터페이스 처리부로 되어 있다. 아날로그부에서는 센서신호를 받아서, PGA (Programmable Gain Amplifier)[2]와 Op-Amp를 사용하여 signal conditioning 처리하여 8차 Lowpass Filter 로 보낸다. Filtering 된 신호는 ADC (Analog to Digital Converter) 가 내장되어 있는 PIC(3) microcontroller로 보내져 AD변환과 디지털 신호 처리를 한다. 처리된 신호는 RS232 인터페이스를 통해 호스트 컴퓨터로 보내 사용자가 분석할 수 있도록 한다. 또한 LCD display 실시간으로 확인, 분석할 수 있으며 동시에analog output에서 센서신호의 특징을 분석 할 수 있도록 한다.