• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.714-722
• /
• 2018

This paper presents a wide-range speed control scheme of brushless DC (BLDC) motors based on a hall sensor with separated low- and normal-speed controllers. However, the use of the hall sensor signal is insufficient to detect motor speed in the low-speed region because of low sensor resolution and time delay. In the proposed method, a micro-stepping current control method according to the torque angle variation is presented. In this mode, the motor current frequency and rotating angle are determined by the reference speed without the actual speed fed by the hall sensor. The detected torque angle is used to adjust the current value in a limited band to control the current value in accordance with the load. The torque angle is detected exactly at the changing point of the hall sensor signal. The rotor can follow the rotating flux with the variable torque angle. In a normal speed range, the conventional vector control scheme is used to control the motor current with a PI speed controller using the hall sensor. The torque characteristics are analyzed on the basis of the back EMF and current shape. To adopt the vector control scheme, the continuous rotor position is estimated by the measured speed and hall sensor position. At the mode changing point between low and normal speed range, the proper initial current command and reference rotor position are calculated. The calculated current command can reduce the torque ripple during transient mode. The proposed method is simple but effective in extending the speed control range of a conventional BLDC motor with hall sensor without the need for a high-resolution encoder. The effectiveness of the proposed method is verified by various experiments on a practical BLDC motor.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.5
• /
• pp.602-608
• /
• 2011

In this study, a method of designing a neurointerface using neural network (NN) is proposed for controlling nonholonomic mobile robots. According to the concept of virtual master-slave robots, in particular, a partially stable inverse dynamic model of the master robot is acquired online through the NN by applying a feedback-error learning method, in which the feedback controller is assumed to be based on a PD compensator for such a nonholonomic robot. The NN for the online feedback-error learning can composed that the input layer consists of six units for the inputs $x_i$, i=1~6, the hidden layer consists of two hidden units for hidden outputs $o_j$, j=1~2, and the output layer consists of two units for the outputs ${\tau}_k$, k=1~2. A tracking control problem is demonstrated by some simulations for a nonholonomic mobile robot with two-independent driving wheels. The initial q value was set to [0, 5, ${\pi}$].

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1015-1020
• /
• 2011

Nanoimprint lithography has been actively investigated. This method can replicate a nanopatterned master stamp onto a thin polymer film on a silicon substrate and so on. In this study, a square-shaped hollow piezoelectric actuator is presented, which is newly developed. This actuator is used for driving a nanoscale stamp in nanoimprint lithography instead of a conventional electric motor. The fabricated prototype actuator has 95 layers and side lengths of 23 mm and 18 mm for the outer and inner squares, respectively. By adopting a novel process instead of the conventional forming process for fabricating a one-layer actuator, the one-layer is composed of four rectangular segments produced by sawing a ceramic film with a thickness of 0.3 mm. The basic characteristics on displacement and generation force of the fabricated prototype actuator are experimentally investigated. Furthermore, the displacement characteristics obtained by using a PI controller are tested and discussed.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.107-117
• /
• 2005

A distributed hardware-in-the-loop simulation (HILS) platform is developed for designing an automotive engine control system. The HILS equipment consists of a widely used PC and commercial-off-the-shelf (COTS) I/O boards instead of a powerful computing system and custom-made I/O boards. The distributed structure of the HILS system supplements the lack of computing power. These features make the HILS equipment more cost-effective and flexible. The HILS uses an automatic code generation extension, REAL-TIME WORKSHOP$^{ (RTW$^{) of MATLAB$^{ tool-chain and RT-LAB$^{, which enables distributed simulation as well as the detection and generation of digital event between simulation time steps. The mean value engine model, which is used in control design phase, is imported into this HILS. The engine model is supplemented with some I/O subsystems and I/O boards to interface actual input and output signals in real-time. The I/O subsystems are designed to imitate real sensor signals with high fidelity as well as to convert the raw data of the I/O boards to the appropriate forms for proper interfaces. A lot of attention is paid to the generation of a precise crank/ earn signal which has the problem of quantization in a conventional fixed time step simulation. The detection of injection! command signal which occurs between simulation time steps are also successfully compensated. In order to prove the feasibility of the proposed environment, a simple PI controller for an air-to-fuel ratio (AFR) control is used. The proposed HILS environment and I/O systems are shown to be an efficient tool to develop various control functions and to validate the software and hardware of the engine control system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.65-73
• /
• 2007

This paper presents an on-line correction method of current measurement errors for a pure-integration-based flux estimation down to 1-Hz stator frequency. An observer-based approach is taken as one possible solution of eliminating the dc offset and the negative sequence component of unbalanced gains in the synchronous coordinate. At the same time, the positive sequence component estimation is performed by creating an error signal between a motor model reference and an estimated q-axis rotor flux established by a permanent magnet (PM) in the synchronous coordinate. The compensator utilizes a PI controller that controls the error signal to zero. The proposed technique further contains a residual error compensator to completely eliminate miscellaneous disturbances in the estimated flux. The developed algorithm has been implemented on a 1.1-kW permanent magnet synchronous motor (PMSM) drive to confirm the effectiveness of the proposed scheme.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.5
• /
• pp.401-408
• /
• 2012

A simple on-line elimination strategy of the dead time and inverter nonlinearity using the current slope information is presented for a PWM inverter-fed IPMSM (Interior Permanent Magnet Synchronous Motor) drive. In a PWM inverter-fed IPMSM drive, a dead time is inserted to prevent a breakdown of switching device. This distorts the inverter output voltage, resulting in a current distortion and torque ripple. In addition to the dead time, inverter nonlinearity exists in switching devices of the PWM inverter, which is generally dependent on operating conditions such as the temperature, DC link voltage, and current. The proposed scheme is based on the fact that the d-axis current ripple is mainly caused by the dead time and inverter nonlinearity. To eliminate such an influence, the current slope information is determined. The obtained current slope information is processed by the PI controller to estimate the disturbance caused by the dead time and inverter nonlinearity. The overall system is implemented using DSP TMS320F28335 and the validity of the proposed algorithm is verified through the simulation and experiments. Without requiring any additional hardware, the proposed scheme can effectively eliminate the dead time and inverter nonlinearity even in the presence of the parameter uncertainty.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.333-338
• /
• 2019

Satellite communication is not used by many people like mobile communication, but it is a necessary technology for public service and communication services, such as providing the Internet in military, disaster, remote education and medical services, island areas, and infrastructure vulnerable areas. However, most communication modems have problems with two-way communication with server as IP addresses are assigned to floating IP that change every time they communicate with the network. In this paper, we used the Raspberry Pi as the controller of the terminal device to communicate the network through the satellite modem and the PPP protocol, and to solve the problem of the modem with the floating IP, we used the text message function of the satellite modem. Through this process, two-way data links using the Thuraya geostationary orbit satellite were implemented.