• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.6
• /
• pp.526-531
• /
• 2012

This paper, we describe the vector control of surface mounted PMSM (Permanent Magnet Synchronous Motor) using the fuzzy controller which is suggested algorithm. In these days, when vehicle is operated or not, whether the road is covered or not, the sensitivity of the steering column is not stable. To make up for it, the PI gain of a steering column controller is adjusted by experience. It becomes the price because it need a lot of sensor. Also it is difficult to implement robust control because we need a lot of parameters for variable road conditions which are the off road, the on road, a low battery voltage, a high battery voltage, a vehicle speed. In this paper, we propose fuzzy controller using the suggested algorithm which suitable for steering system. We test the fuzzy controller with the various condition. We get the good performance of fuzzy controller even if it is nonlinear system. We check a robust the fuzzy controller using the suggested algorithm.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.12
• /
• pp.1976-1980
• /
• 2006

We have calculated the reaction probability and the reaction cross-section of the $N(^4S)+O_2(X^3\sum_{g}^{-})\;\rightarrow\;NO(X^2\Pi)+O(^3P)$ reaction by the quasiclassical trajectory method with the 6th-order explicit symplectic algorithm, based on a new ground potential energy surface. The advantage of the 6th-order explicit symplectic algorithm, conserving both the total energy and the total angular momentum of the reaction system during the numerical integration of canonical equations, has firstly analyzed in this work, which make the calculation of the reaction probability more reliable. The variation of the reaction probability with the impact parameter and the influence of the relative translational energy on the reaction cross-section of the reaction have been discussed in detail. And the fact is found by the comparison that the reaction probability and the reaction cross-section of the reaction estimated in this work are more reasonable than the theoretical ones determined by Gilibert et al.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.58-64
• /
• 2016

This study presents a design method for a single-loop voltage controller that is suitable for an arbitrary waveform generator (AWG). The voltage control algorithm of AWG should ensure high dynamic performance and should attain sufficient robustness to disturbances such as inverter nonlinearity, sensor noise, and load current. By analyzing the power circuit of AWG, control limitation and control target are presented to improve the dynamic performance of AWG. The proposed voltage control algorithm is composed of a single-loop output voltage control, an inverter current feedback term to improve transient response, and a load current feedforward term to prevent voltage distortion. The guideline for setting control gain is presented based on output filter parameters and digital time delay. The performance of the proposed algorithm is proven by experimental results through comparison with the conventional algorithm.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.685-688
• /
• 2003

In this paper, a performance comparison between two blind signal estimation algorithms in a LTI channel is considered. The two algorithms, Iterative Least-Squares with Projection (ILSP) and a modified ILSP, are based on the finite-alphabet property of input symbols. This case typically arises in a multiple access system with a sensor array antenna at the receiving end. We start with the formulation of a maximum-likelihood (ML) estimation problem under an additive white Gaussian noise assumption. A blind ML estimator is derived with its iterative algorithm for calculation. Then we narrow down the consideration of this problem to QPSK case so that a modified algorithm is proposed for $\pi$/4-QPSK case. The modified version is compared with the original ILSP algorithm in terms of the rate of the convergence to global minima. A computer simulation shows that the modified algorithm gives a better performance. This result implies that the performance of the blind separation algorithms may be greatly improved by adopting a smart coding scheme with rich structure.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.27-33
• /
• 1997

In this paper, instantaneous controller of a single-phase PWM converter is realized using DSP. The stable PI gain of the input current and the DC link voltage control system is designed. The DC link voltage control system can be designed in continuous-time domain. But as for the input current control system, the descretizing effect cannot be ignored so it must be designed in descrete-time domain considering the calculation time. The capacitance estimating algorithm which can be acquired through the ripple voltage is proposed. By this algorithm the DC link capacitance can be estimated even under the transient state. Experimental results show the input power factor of 99.1% and the voltage variation rate of $\pm$5% according to the load variation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.199-202
• /
• 2002

Moire topography method is a well-known non-contacting 3-D measurement method. Recently, the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. 3-D measurement using digital projection moire topography is very attractive because of its high measuring speed and high sensitivity. In this paper, using different N-bucket algorithm method of digital projection moire topography is tested to measuring object with the 2$\pi$-ambiguity problem. Experimental results prove that the proposed scheme is capable of finding measurement errors that decreased more by using the flour-three step algorithm method than the same step in the phase shifting of different pitchs.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1231-1234
• /
• 1992

In this paper a self-tuning control algorithm has been utilized to control speed of a rolling mill DC drive system. Inner current control loop is composed of predictive current controller and the outer speed control loop is composed of the self-tuning PI or IP controller. Computer simulation results reveal that the adaptive control algorithm using self-tuning control is capable of following the typical set point variations required for a rolling mill in conjunction with load torque variations on the shaft of the drive.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.384-394
• /
• 2002

In this paper, a new control strategy is proposed to improve the quality of the welding products. The conventional nonlinear power control system of spot welders is linearized using nonlinear feedback linearization technique based on differential geometry theory. An evolution strategy(ES) geometry is used to find optimal gain of PI controllers. It tries to find out the optimal control parameters by imitating the natural evolution. Some Simulation and experimental results show that the proposed variable power control system using ES algorithm has better dynamic performances than the conventional one.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.30-32
• /
• 2005

Mobility of an indoor wheeled robot is affected by adhesion force that is related to various floor conditions. When the adhesion force between driving wheels and floor decreases suddenly, the robot begins slip. In order to overcome this slip problem, optimal slip velocity must be decided for stable movement of wheeled robot. First of all, this paper shows that conventional PI control can not be applied to a wheeled robot of the light weight. Secondly, proposed fuzzy logic is applied to the Takagi-Sugeno model for the configuration of fuzzy sets. For the design of Takagi-Sugeno model and fuzzy rule, proposed algorithm uses FCM(Fuzzy c-mean clustering method) algorithm. The proposed fuzzy logic controller(FLC) is pretty useful with prevention of the slip phenomena for the controller performance in the re-adhesion control strategy.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.232-238
• /
• 2015

A sensorless control algorithm of brushless DC (BLDC) motors with a model current based on 120 degree conduction mode is proposed in this paper. The rotor speed and position can be estimated using the current model of BLDC motor, which is a modified version of the conventional current model of permanent magnet synchronous motor. The rotor speed and position can be obtained using the difference of the actual current and the model current. The position error caused by the parameter errors of the model current is compensated using a PI controller and the feedback loop of the real current. The validity of the proposed sensorless control algorithm is verified through simulation.