• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.76.4-76
• /
• 2002

$\textbullet$ Contents 1 Introduction $\textbullet$ Contents 2 Model of Two-inertia System $\textbullet$ Contents 3 Concept of CDM $\textbullet$ Contents 4 Controller Design $\textbullet$ Contents 5 Experimental Results $\textbullet$ Contents 6 Conclusions

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.175-178
• /
• 2002

In a conventional speed sensorless Stator Flux Oriented(SFO) induction machine drive system, the estimated speed is delayed in transients by the use of a low pass filter(LPF). To prevent extreme overshoot caused by this delay, PI controller gains should be small, which consequently is greatly affected by disturbance torque. In this paper, by taking advantage of disturbance torque observer and feedforward control, robust speed controller is designed for speed sensorless SFO system. The proposed method is verified by the simulation results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.1
• /
• pp.49-55
• /
• 2019

This study proposes a robust control of a fin position servo system using the H-infinity loop-shaping method. The fin position control system has a proportional (P) position controller and a proportional-integral (PI) controller. In this work, the position control loop requires a wide bandwidth. No current control loop exists due to the compact design of the system. Hence, the controller parameters are difficult to determine using the traditional cascade design method. The $H_{\infty}$ controller design method is used to design the controller's gain to achieve good performance and robustness. First, the transfer function of the system, which can be divided into tunable and fixed parts, is derived. The tunable part includes the position P controller and speed PI controller. The fixed part includes the rest of the system. Second, the optimized controller parameters are calculated using Matlab $H_{\infty}$ controller design program. Finally, the system with optimized controller is tested by simulation and experiment. The control performance is satisfactory, and the $H_{\infty}$ controller design method is proven to be valid.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.6
• /
• pp.9-13
• /
• 2009

In the three axis control of Low Earth Orbit (LEO) satellite by using reaction wheel and gyro, a reaction wheel produces the control torque by the wheel speed or momentum, and a gyro carries out measuring of the attitude angle and the attitude angular velocity. In this paper, the dynamic modelling of LEO is consisted of the one from the rotational motion of the satellite with basic rigid body model and a flexible model, in addition to the reaction wheel model. A robust controller $(H_\infty)$ is designed to stabilize the rigid body and the flexible body of satellite, which can be perturbed due to disturbance, etc. The result obtained by $H_\infty$ controller is compared with that of the PI (Proportional and Integration) controller, which has been traditionally using for the stabilizing LEO satellite.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.9
• /
• pp.813-821
• /
• 2000

In this paper, we developed modeling of tension and speed dynamics for a two-drum winder in a three span continuous web transport system which had not been previously. Dynamic modeling of the time-varying nonlinear system was derived by considering the effect of the radii and mass moment of inertia in the unwinder and the two-drum winder through winding up the web. After linearizing it, we designed with a variable-gain a PID controller for tension control and a PI controller for speed. Simulation is carried out with the variation of radii and moment of inertia at high speed for the proposed tension control system with the two-drum winder and the variavle-gain a PID controller. Results show good performance of tension control during the speed change speed at a start-up and stop.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.761-768
• /
• 2017

This paper deals with the performance analysis of three phase induction motor considering its stator side faults and operating thermal limits. The speed control of induction motor using three phase boost converter operated by a MOSFET switch and a PI controller is demonstrated and presented in this article. IGBTs switches are used for inverter drive mechanism. The experimental result of speed control of induction motor using voltage control technique clearly shows better accuracy than conventional methods of speed control. A three phase 1HP 415V 0.78 kW 4 Pole induction motor is designed using motor solver software. Based on the parameters used in the software thermal analysis of induction motor is done and torque variation with conductor area, efficiency, output curve, losses in different parts of motor has been obtained. Also different types of faults namely under voltage, over voltage, stator imbalanced voltage, turn to turn, locked rotor bar, wrong alignment of rotor bar with respect to stator are studied and fault analysis is performed. Hence comparison is made based upon the results obtained before and after faults.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2006

This paper proposes a full fuzzy-logic-based vector control for a permanent-magnet synchronous motor (PMSM). The high-performance of the proposed fuzzy logic control (FLC)-based PMSM drive are investigated and compared with the conventional proportional-integral (PI) controller at different conditions, such as step change in command speed and load and etc. In the experimental and simulation the FLC is employed in the speed and current controller. The experimental results show to be a suitable replacement of the conventional PI controller for the high-performance drive system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.88-94
• /
• 2003

The DC motor has the strong characteristics in the speed response, the system parameter variations and the external influence and is used as the speed controller with its good starting torque in the distributing industry. However development of the Microprocessor which is for high speed switching program can make better control system. This paper introduce to design of the high-effective DC motor controller that is using Software Bang-Bang Program of Fuzzy algorithm and to verity a PI controller and a Fuzzy controller.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.820-823
• /
• 2003

In this paper, we describe a design procedure for cascade controller for induction motor drives based on Genetic Algorithms(GAs). Most electric drives have two separate controllers for current and speed control, which are in general designed in two consecutive steps(firstly the current controller and then the speed controller). We search simultaneously for the couple of discrete anti-windup controllers achieving the optimal compromise of weighted cost and performance indices related to both current and speed responses.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.1024-1031
• /
• 2013

This paper addresses linear quadratic regulation (LQR) for variable speed variable pitch wind turbines. Because of the inherent nonlinearity of wind turbines, a set of operating conditions is identified and then a LQR controller is designed for each of the operating points. The feedback controller gains are then interpolated linearly to get a control law for the entire operating region. In addition, the aerodynamic torque and effective wind speed are estimated online to get the gain-scheduling variable for implementing the controller. The potential of this method is verified through simulation with the help of MATLAB/Simulink and GH Bladed. The performance and mechanical load when using LQR are also compared with those obtained when using a PI controller.