• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.212-218
• /
• 2007

This paper presents a implementation of speed sensorless vector control of induction motor using MATLAB/SIMULINK and dSPACE DS1104. Proposed flux estimation algorithm, which utilize the combination of the voltage model based on stator equivalent model and the current model based on rotor equivalent model, enables stable estimation of rotor flux. Proposed rotor speed estimation algorithm utilizes the estimated flux. And the estimated rotor speed is used to speed control of induction motor. Overall system consists of speed controller, current controller, and flux controller using the most general PI controller. Speed sensorless vector control algorithm is implemented as block diagrams using MATLAB/SIMULINK. And realtime control is performed by dSPACE DS1104 control board and Real-Time-Interface(RTI).

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.145-147
• /
• 2007

This paper presents an implementation of vector control for SMPMSM using model based controller design in MATLAB/SIMULINK. The model based controller design enables fast development of control system for motor by designing controllers and performing simulation on the GUI (Graphic User Interface) platform, converting program code directly into real-time programs, and then performing tests for the responses from controllers. The controller is designed as PI controller for speed and decoupling PI controller for current. And PWM used space vector modulation method using offset voltage and system stability is also secured by close magnitude overmodulation method, maintaining dynamics of load when it overmodulation. The validity of vector control implemented is verified through simulations and experiments.

• Journal of Industrial Technology
• /
• v.22 no.B
• /
• pp.185-190
• /
• 2002

This paper describes a design of an induction motor control system using a 2 degree-of-freedom PI controller to compensate the effects of disturbance without degrading tracking performance. On the basis of vector control principle, the control system is simulated by using the ACSL and implemented on a DSP system(TMS320C31). In designing the 2 DOF controller, we can tune the performance of either the tracking or disturbance rejection independently without affecting the other. With the experimental results, the 2 DOF controller has shown a better performance in command tracking and disturbance rejection than a conventional PI controller.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1383-1391
• /
• 2008

This paper presents an implementation of vector control for SPMSM using model based controller design in MATLAB/SIMULINK. The model based controller design enables fast development of control system for motor by designing controllers and performing simulation on the GUI (Graphic User Interface) platform, converting program code directly into real-time programs, and then performing tests for the responses from controllers. The controllers designed in this paper are PI speed controller and decoupling PI current controller. Also space vector modulation method using offset voltage is used in PWM scheme. And system stability is also secured by close magnitude overmodulation method, maintaining dynamics of load when overmodulation occurs. The validity of vector control implemented is verified through simulations and experiments.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.3
• /
• pp.295-300
• /
• 2018

Conventionally, a PI control algorithm has been widely used as a speed control algorithm for BLDC motor. The PI control algorithm has a disadvantage in that is slow to reach the steady state due to the slow speed and torque response with various speed changes. Therefore, in this paper, PWM fuzzy logic control algorithm which can reach the steady state quickly by improving the response speed although there is a little overshoot is proposed. PWM reduces response speed and fuzzy logic control algorithm minimizes overshoot. The proposed PWM fuzzy logic control algorithm consists of DC chopper, PWM duty cycle regulator, and fuzzy logic controller. The performance and validity of the proposed algorithm is verified by simulation with Simulink of Matlab 2018a.

• Journal of Power Electronics
• /
• v.11 no.4
• /
• pp.393-400
• /
• 2011

The main objective of this paper is to control the speed of Nonlinear Hybrid Electric Vehicle (HEV) by controlling the throttle position. Various control techniques such as well known Proportional-Integral-Derivative (PID) controller in conjunction with state feedback controller (SFC) such as Pole Placement Technique (PPT), Observer Based Controller (OBC) and Linear Quadratic Regulator (LQR) Controller are designed. Some Intelligent control techniques e.g. fuzzy logic PD, Fuzzy logic PI along with Adaptive Controller such as Self Organizing Controller (SOC) is also designed. The design objective in this research paper is to provide smooth throttle movement, zero steady-state speed error, and to maintain a Selected Vehicle (SV) speed. A comparative study is carried out in order to identify the superiority of optimal control technique so as to get improved fuel economy, reduced pollution, improved driving safety and reduced manufacturing costs.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.207-214
• /
• 2009

This paper presents a modem approach for speed control of a PMSM using the Particle Swarm Optimization (PSO) algorithm to optimize the parameters of the PI-Controller. The overall system simulated under various operating conditions and an experimental setup is prepared. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. Comparison between different controllers is achieved, using a PI controller which is tuned by two methods, firstly manually and secondly using the PSO technique. The system is tested under variable operating conditions. Implementation of the experimental setup is done. The simulation results show good dynamic response with fast recovery time and good agreement with experimental controller.

• Journal of Wind Energy
• /
• v.4 no.2
• /
• pp.17-24
• /
• 2013

Idealized PID-controlled rotor-speed error for blade pitch control of wind turbines responds as a second-order system with natural frequency and damping ratio for closed-loop system. RISO National Laboratory has recommended specific natural frequency(=0.6 rad/s) and damping ratio(=0.7) for 2 MW wind turbine. The baseline controller for 5 MW wind turbine of NREL(National Renewable Energy Laboratory) is designed based on the same values of RISO recommendation. This study investigates the effect of the natural frequency and damping ratio of the controller for NREL 5 MW wind turbine. It is confirmed that RISO recommendation shall be tuned for each wind turbine.

• Journal of Power Electronics
• /
• v.5 no.2
• /
• pp.129-141
• /
• 2005

A high-performance robust hybrid speed controller for a permanent-magnet synchronous motor (PMSM) drive with an on-line trained neural-network model-following controller (NNMFC) is proposed. The robust hybrid controller is a two-degrees-of-freedom (2DOF) integral plus proportional & rate feedback (I-PD) with neural-network model-following (NNMF) speed controller (2DOF I-PD NNMFC). The robust controller combines the merits of the 2DOF I-PD controller and the NNMF controller to regulate the speed of a PMSM drive. First, a systematic mathematical procedure is derived to calculate the parameters of the synchronous d-q axes PI current controllers and the 2DOF I-PD speed controller according to the required specifications for the PMSM drive system. Then, the resulting closed loop transfer function of the PMSM drive system including the current control loop is used as the reference model. In addition to the 200F I-PD controller, a neural-network model-following controller whose weights are trained on-line is designed to realize high dynamic performance in disturbance rejection and tracking characteristics. According to the model-following error between the outputs of the reference model and the PMSM drive system, the NNMFC generates an adaptive control signal which is added to the 2DOF I-PD speed controller output to attain robust model-following characteristics under different operating conditions regardless of parameter variations and load disturbances. A computer simulation is developed to demonstrate the effectiveness of the proposed 200F I-PD NNMF controller. The results confirm that the proposed 2DOF I-PO NNMF speed controller produces rapid, robust performance and accurate response to the reference model regardless of load disturbances or PMSM parameter variations.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.30-37
• /
• 2004

This thesis develops a fuzzy-PID control algorithm for control the filament winding tension. It is developed by applying classical PID control technique to a fuzzy logic controller. It is composed of a fuzzy-PI controller and a fuzzy-D controller. The fuzzy-PI controller uses error and integrated error as inputs, and the fuzzy-D controller uses derivative of error as input. The fuzzy-PI controller uses Takagi-Sugeno fuzzy inference system, and the fuzzy-D controller uses Mamdani fuzzy inference system. The fuzzy rule base for the fuzzy-PI controller is designed using 19 rules, and the fuzzy rule base for the fuzzy-D controller is designed using 5 rules. A test-bed is set-up for verifying the effectiveness of the developing control algorithm in control the filament winding tension. It is composed of a mandrel, a carriage, a force sensor, a driving roller, nip rollers, a creel, and a real-time control system. Nip rollers apply a vertical force to a filament, and the driving roller drives it. The real-time control system is developed by using MATLAB/xPC Target. First, experiments for showing the inherent problems of an open-loop control scheme in a filament winding are performed. Then, experiments for showing the robustness of the developing fuzzy-PID control algorithm are performed under various working conditions occurring in a filament winding such as mandrel rotating speed change, carriage traversing, spool radius change, and reference input change.