• Macromolecular Research
• /
• v.13 no.6
• /
• pp.529-532
• /
• 2005

A novel amphiphilic, symmetric rod-coil, triblock copolymer (denoted as PHEMA-b-PF-b-PHEMA) of poly(9,9-didodecylfluorene-2,7-diyl) (PF) and poly(hydroxyl ethyl methacrylate) (PHEMA) was synthesized. A $\pi$-conjugated poly(9,9-didodecylfluorene-2,7-diyl) (PF) was used as a rodlike midblock segment and connected with hydrophilic end blocks of poly(hydroxyl ethyl methacrylate) (PHEMA) by using an ATRP technique. The chemical structure of PHEMA-b-PF-b-PHEMA was confirmed by $^{1}H$-NMR and GPC, and its PL properties were investigated in selected solvents. Due to the dissimilarities in molecular conformation and solubility between PHEMA and PF blocks, both block segments were segregated to display a phase-separated morphology on a Si wafer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.159-162
• /
• 1998

The new type polymer electrolyte composed of polyacrylonitrile(PAN) baed polymer electrolyte contain LiClO$_4$-EC/PC and LiPF$\sub$6/-EC/PC were developed for the weightless and long or life time of lithium polymer battery system with using polyaniline electrode. The gel type electrolytes were prepared by PAN at different lithium salts in the glove box. We prepared for polymer electrolyte with knife casting method. The minimum thickness of PAN gel electrolyte for the slim type is about <400∼500$\mu\textrm{m}$. These gel electrolytes showed good compatibility with lithium electrode. The test cell of Li/polymer electrolyte/Lithium cobalt oxide solid state cell which was prepared by different lithium salt was researched by electrochemical technique. Resistance of polymer electrolyte which consist of LiClO$_4$ is more less than that of LiPF$\sub$6/ and cycle life is more longer than that of LiPF$\sub$6/.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.1945-1950
• /
• 2007

Two fluorene-based conjugated copolymers containing hexyl-thiophene derivatives, PF-1T and PF-4T, were synthesized via the palladium-catalyzed Suzuki coupling reaction. The number-average molecular weights (Mn) of PF-1T and PF-4T were found to be 19,100 and 13,200, respectively. These polymers were soluble in common organic solvents such as chloroform, chlorobenzene, toluene, etc. The UV-vis absorption maximum peaks of PF-1T and PF-4T in the film state were found to be 410 nm and 431 nm, respectively. Electrochemical characterization revealed that these polymers have low highest occupied molecular orbital (HOMO) levels, indicating good resistance against oxidative doping. Thin film transistor devices were fabricated using the top contact geometry. PF-1T showed much better thin-film transistor performance than PF-4T. A thin film of PF- 1T gave a saturation mobility of 0.001-0.003 cm2 V?1 s?1, an on/off ratio of 1.0 × 105, and a small threshold voltage of ?8.3 V. To support TFT performance, we carried out DSC, AFM, and XRD measurements.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.2 no.1
• /
• pp.15-22
• /
• 2015

Poly(ethylene glycol) end-capped with pentafluorophenyl group(s) in ABA (FP-PEG-FP) and AB (mPEG-FP) types were prepared. Even though they were similar in composition, the lower critical solution temperature (LCST) of FP-PEG-FP was observed at $23^{\circ}C$, whereas that of mPEG-FP was observed at $65^{\circ}C$. To understand the large difference in solution behaviour of the two polymers, UV-VIS spectroscopy, microcalorimetry, 1H-NMR spectroscopy, and dynamic light scattering were used. FP-PEG-FP has two hydrophobic pentafluorophenyl groups at the ends of hydrophilic PEG (1000 Daltons), whereas mPEG-PF has a highly dynamic PEG (550 Daltons) block that are anchored to a hydrophobic pentafluorophenyl group. PF-PEG-PF not only has a smaller conformational degree of freedom than mPEG-PF but also can form extensive intermolecular aggregates, therefore, PF-PEG-PF exhibits a significantly lower LCST than mPEG-PF. This paper suggests that topological control is very important in designing a temperature-sensitive polymer.

• Macromolecular Research
• /
• v.16 no.3
• /
• pp.247-252
• /
• 2008

Lithium gel electrolytes based on a mixed polymer matrix consisting of poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) and cyanoresin type M (CRM) were prepared using an in situ blending process. The CRM used in this study was a copolymer of cyanoethyl pullulan and cyanoethyl poly(vinyl alcohol) (PVA) with a mole ratio of 1:1. The mixed plasticizer was ethylene carbonate (EC) and propylene carbonate (PC) with a volume ratio of 1:1. In this study, the presence of PVDF in the electrolytes helps to form a dimensionally stable film over a broad composition range, and decreases the viscosity. In addition, it provides better rheological properties that are suitable for the extrusion of thin films. However, the presence of HFP has a positive effect on generating an amorphous domain in a crystalline PVDF structure. The ionic conductivity of the polymer electrolytes was investigated in the range 298-333 K. The introduction of CRM into the PVDF-HFP/$LiPF_6$, complex produced a PVDF-HFP/CRM/$LiPF_6$ complex with a higher ionic conductivity and improved thermal stability and dynamic mechanical properties than a simple PVDF-HFP/$LiPF_6$, complex.

• Journal of the Korean Chemical Society
• /
• v.42 no.6
• /
• pp.664-671
• /
• 1998

Poly pyrrole polymer(ppy) has an excellent electrical conductivity and can be easily polymerized on anode to give various morophology according to doped anion on electroactive sites. To improve the properties of brittleness, ageing and hydrophobisity, poly furan polymer(pfu) having a high initiation potential was anodically implanted in this porous ppy film matrix to get the Pt/ppy/pfu(x)type of polymer composite electrode. Cyclic voltammetry and electrochemical impedance methods were used to these electrode, where $PF_6^-,\; BF_4^-$, and $ClO_4^-$ ions were employed as dopants. The composition of the pfu(x) at the electrode was changed from 0 to 1.10, but the range was useful only at 0.1 to 0.2 as the redox electrode. The polymer composite electrode doped with $PF_6^-$ was better in charge transfer resistance by a factor of 40 times and in double layer capacitance by a factor of 20 times than others. The charge transfer in the polymer film of the electrode was influenced on frequency change and equivalent circuit of this electrode had Warburg impedance including mass transfer.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.288-291
• /
• 2005

Resol type phenol-formaldehyde (PF) resin was synthesized by addition reaction of formaldehyde (F) and phenol (P). And the PF resin was synthesized by condensation reaction in which water was removed. In this work, we studied the influence of experimental parameters in the addition reaction, such as F/P mole ratio, amount of catalyst, reaction temperature, reaction time, and so on. Also, we studied the influence of molecular weight and viscosity of PE resin as a function of condensation time. As a result, in addition reaction, the reaction time decreased remarkably as the catalyst concentration increased, and the time decreased with increasing reaction temperature at a constant catalyst concentration. Also, in condensation reaction, the viscosity of resol type PF resin increased from 1500 to 9000 cps as a function of condensation time; molecular weight showed from 500 to 1100 g/mol.

• Journal of Life Science
• /
• v.26 no.6
• /
• pp.633-639
• /
• 2016

Biomaterials including polymer, metal, ceramic, and composite have been widely applied for medical uses as medical fibers, artificial blood vessels, artificial joints, implants, soft tissue, and plastic surgery materials owing to their physicochemical properties. However, the biocompatibility and toxicity for film- and plate-form biomaterials is difficult to measure in mammalian cells because there is no appropriate incubation system. To solve these problems, we developed a novel mammalian cell culture system consisting of a silicone ring, top panel, and bottom panel and we applied two polymer films (PF) and one metal plate (MP). This system was based on the principal of sandwiching a test sample between the top panel and the bottom panel. Following the assembly of the culture system, SK-MEL-2 cells were seeded onto Styela Clava Tunic (SCT)-PF, NaHCO₃-added SCT (SCTN)-PF, and magnesium MP (MMP) and incubated at 37℃ for 24 hr and 48 hr. An MTT assay revealed that cell viability was maintained at a normal level in the SCT-PF culture group at 24 or 48 hr, although it rapidly decreased in the SCTN-PF culture group at 48 hr. Furthermore, the cell viability in the MMP culture group was very similar to that of the control group after incubation for 24 hr and 48 hr. Together, these results suggest the sandwich-type mammalian culture system developed here has the potential for the evaluation of the biocompatibility and toxicity of cells against PF- and MP-form biomaterials.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.252-252
• /
• 2006

Utilizing the existence of the induction period in photo-polymerization, we propose a new injection method of photo-polymerizable, thermocrosslinking hydrogels made of di-acrylated Pluronic F127 (DA-PF127). This method can solve the problem of fast dissolution of thermal gelation as a scaffold and the disadvantages of the existing injection method that photo-polymerize di-acrylated Pluronic polymer after injection using optical fiber. Injectable gelation of DA-PF127 by the proposed method was demonstrated both in vitro and in vivo. The enhanced stability by this novel photo-polymerization strategy was confirmed by the more sustained release of loaded protein as well as the prolonged degradation time of the hydrogels.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.4
• /
• pp.339-346
• /
• 2007

The influence of adding urea to phenol-formaldehyde (PF) resins as a co-polymer component were investigated aiming at synthesizing useful phenol-urea-formaldehyde resins. Urea was added at 10% by total resin weight. Several methods for the addition of urea to the PF resins during synthesizing resins to see the co-polymerization occurs between urea and PF resins. The urea was added at the beginning, at three different middle stages, and at the end of PF resin synthesis. The copolymerized methylene bridges between phenol and urea molecules were not observed by $^{13}C-NMR;$ no signal around 50ppm. The curing of urea-modified PF resins, evaluated by dynamic mechanical analysis(DMA), showed some differences among the resins. DMA gel times ranged from 2.75 min to 3.25 min and the resins made with earlier urea additions showed slightly shorter gel times. The longest cure time and gelation time was observed for the resin PFU. Catalyst effects on the DMA cure time values of resins were not significant with different amounts of catalyst or different types of catalyst for all resins tested. Gel times of urea-modified PF resins shortened the most by triacetin catalyst.